Lock Mechanisms - Rage University
Contents
1. key operated lock mechanism HN OF FF WD N e GE EN eg kleene ek ele eel a mol control split Schlage Primus anti wrenching pin strike interchangeable core 54 oN ee O Ee q mm mi rk m Locking It Up Answers Examination 55 THOMSON EDUCATION DIRECT 925 Oak Street Scranton Pennsylvania 18515 0001 Lock Mechanisms When you feel confident that you have mastered the material in this study unit complete the following examination Then submit only your answers to the school for grading using one of the examination answer options described in your Test Materials envelope Send your answers for this examination as soon as you complete it Do not wait until another examination is ready Questions 1 20 Select the one best answer to each question 1 A plug follower is used in the disassembly of A a combination padlock C all locks made in the United States B all disk tumbler locks 2 A lock mechanism containing more than two sets of top and bottom pins would be called a C combination lock B wafer tumbler mechanism D lock plug 56 Examination 3 Which of the following lock mechanisms is commonly used in General Motors automobiles A Warded lock C Padlock B Lever tumbler lock 4 What is a case ward A A warded padlock B A special cut in a bit key D A lock used on a Suitcase or briefcase 5 A cam lock is a type of A high security pin tumbler lock C le2. High Security Strikes One of the most popular methods of forcing entry to a home is kicking in the door Unless the door is unusually thick or strong the wood of the door will usually splinter around the lock and allow the burglar to get in To prevent this a high security strike has extra long screws that add strength to the door frame making it very difficult to kick in a door FIGURE 38 A high security strike has extra long screws that add strength to the door frame SCREWS 34 Lock Mechanisms Interchangeable Cores FIGURE 39 An Interchangeable Core Interchangeable or removable cores are specially designed lock cylinders that can be removed from a door lockset without disassembling the lock or door knob An interchangeable core is shown in Figure 39 They can easily be removed and rekeyed using a special key called a control key To remove the core the control key is inserted and turned and the core is then withdrawn RETAINER PLATE N HOLE PLUGS ___ ob a ano WZ PLUG SLEEVE Most of these locks are used in commercial installations The advantage of the interchangeable core is that if for example an employee loses a key to a store the locksmith can simply re move the core rekey it and replace it With another type of lock the locksmith might have to remove the entire lock from the door to replace or rekey it which is much more time consuming and costly Key Operated Padl
3. s very simple to look inside the lock bypass the wards with a pick and release the locking mechanism to disengage the latch or bolt and open the door The simplest method of picking a warded lock is to use a pick key Several pick keys for warded locks are illustrated in Figure 9 A pick key is a spe cially ground and cut piece of flat steel that will fit into the keyway of a lock A small curved projection is left near the tip of the key pick The remain der of the key pick is quite nar row A pick key will open all but a few warded lock types As you can see by the variety of ward cuts on these pick keys it s a simple matter to select a pick key and turn it gently in the lock If you feel an internal ward interfering with the pick key you simply stop and try another pick key However despite the relative lack of security in warded locks note that there are cir cumstances when the simplic ity of the warded lock is an Lock Mechanisms advantage For example warded padlocks are a good choice for use in wet sandy or dusty environments where a more complex lock would rust or jam easily Cleaning Lubrication and Repair of Warded Locks Often a warded lock will stop working or will work only with difficulty Note that while it s usually easier and cheaper to replace a warded lock than repair it a customer may want an old lock repaired anyway This is especially true in very old homes where the owner may w
4. be able to remove the lock using bolt cutters Otherwise it will be necessary to drill a small hole in the back of the lock to try to see the combination Drill a small Ycinch hole in the back of the padlock case By looking inside the mecha nism you can see the position at which all the wheels are aligned Figure 45 shows where to drill the hole which you can patch with liquid solder or liquid cement when Lock Mechanisms 43 you re finished The exact position of the hole might vary de pending on the type and brand of lock Combination Entry Locks FIGURE 46 A Pushbutton Combination Lock The pushbutton combination lock in Figure 46 is a popular type of combination entry lock used in both home and commercial applications These locks are especially common in hotels or other facilities where many strangers come and go at will In stead of having to supply each person with a key a three number combination is supplied The combination can be changed quickly and easily to maintain security If desired a security shield can be mounted around the lock face to screen it from curious eyes An additional advantage of the pushbutton combi nation entry lock is that it s easy to in stall In a wooden door two drilled holes are all that is required For metal doors a surface mounted strike is provided eliminat ing the need to mortise the jamb Now that you understand the basic operation of
5. combination As the dial is turned the wheels inside are aligned Each time a correct number from the combination is dialed another wheel clicks into place When all the numbers have been dialed the wheels will be completely aligned free ing the lock to open To see how this works in more detail let s say we want to open a padlock with the combination 18 5 15 First spin the dial a couple of times to clear it and then align the zero un der the arrow at the top of the dial Next we d turn the dial clockwise two full turns and continue to turn until number 18 is aligned under the arrow The first wheel inside the mechanism is now set Next move the dial counterclockwise one full turn and stop at number 5 The first and second wheel are now aligned Finally turn the dial clockwise until number 15 is aligned under the arrow All three wheels should now be aligned inside the mechanism and the shackle should be free to open In some models the shackle will pop up out of the case impelled by a spring in others you must pull down on the case to release the shackle Lock Mechanisms FIGURE 43 This figure shows how the gates on the wheels must align in order to free the locking mechanism 41 If you look at a back view of the combination lock you can see how the lock releases the shackle Figure 43 displays this back view of the lock Notice how the wheel has a gate cut into it When the proper combination is diale
6. 9 In a disk tumbler lock the rectangular cuts in the disks are always in the same position 10 Disk tumbler locks are seldom used today Check your answers with those on page 53 20 Lock Mechanisms The Pin Tumbler Mechanism FIGURE 21 Exterior View of a Pin Tumbler Cylinder and Plug The pin tumbler lock is the most secure and widely used lock today This type of lock is very popular in home entry locks padlocks and other types of locking devices A pin tumbler mechanism is contained within a device called a cylinder Pin tumbler cylinders can be installed in a variety of products in a door knob in a door surface or in a car igni tion While each of these locks functions differently from the outside the pin tumbler cylinder itself always works the same way Pin tumbler lock mechanisms are always operated with cylinder keys Construction A pin tumbler cylinder contains the following parts the plug the keyway the top pins the bottom pins and the springs Let s start our discussion by examining these parts Figure 21 shows an exterior view of a pin tumbler cylin der and a plug The cylinder is the rounded shell that surrounds and holds the plug which is the central assembly of the mechanism The plug is a small tube that contains the bottom pins Figure 22 Note the five holes that were drilled along the length of the plug each contain ing a bottom pin Many pin tumbler mechanisms
7. anchor embedded in the door resisting attempts to wrench the cylinder loose 5 A high security has extra long screws that add strength to a door frame making it very difficult to kick in a door 6 A an is a specially designed lock cylinder that can be removed from a door lockset without disassembling the lock or door knob Check your answers with those on page 53 en Lock Mechanisms 39 COMBINATION LOCK MECHANISMS Introduction Operation Let s stray away from key operated locks for a short time and look at a lock that needs no key This type of lock is called the combination lock mechanism Combination lock mechanisms are used in many types of padlocks door entry systems safes and vaults Although combination locks differ in construction from one make and model to another they all operate on the same basic principles Combination locks have a practically unlimited number of applications from school lockers to trailer hitches to safes They re particularly advantageous over key operated locks in situations where several people lab workers industrial inspectors high school teachers need access to the same equipment at random times In a manufacturing plant for example six or eight workers may need to use tools or sup plies that are too valuable to be left out in the open Rather than provide each person with a key which could be lost or stolen requiring immediate rekeying or lock replacement each can be
8. compressed With the key located in the plug turn the plug slowly while pulling outward The plug should slide from the shell Once the plug is removed you can begin removing the disks The disks may lift right out or they may need to be pinched to allow removal depending on the type of lock As each disk is removed from the lock place it in order in a pin tray or other small container To reassemble the lock reload the disks into the plug Then insert the plug into the shell applying only as much pressure as is necessary for the end of the plug to engage the retainer clip Disassembling a Side Bar Wafer Lock Since most side bar wafer locks are found in cars you ll need to remove it from the vehicle before you can disassemble the lock itself In gen eral ignition and trunk locks are removed by driving out a retaining pin to release the lock shell In a door lock a special retaining clip may be used to hold the lock shell We ll dis cuss the exact details on removing locks from automobiles in a later study unit If you want more information now you can consult any automotive service manual To disassemble this type of lock you will have to remove the spring and disk retainer cover Pry upwards on the cover with 18 Lock Mechanisms a small screwdriver and it will come free of the shell Note Very often this cover will be bent or distorted upon removal and require replacement after you have moved the discs These c
9. con tain five pins but there are six and even seven pin arrangements The keyway is the opening in the plug that allows a key to be inserted Lock Mechanisms FIGURE 22 Plug and Bottom Pins FIGURE 23 Here is an interior view of a typical pin tumbler lock 21 Now look at Figure 23 which shows an interior view of a pin tum bler cylinder The visible components of the pin tumbler lock are the plug and the cylinder This view also shows the internal components the bottom pins the top pins and the springs BOTTOM PINS KEYWAY Note the placement of the plug inside the cylinder Inside the cylinder directly above the five holes in the plug are five more drilled holes each containing a top pin Above each top pin is a small metal spring The spring retainer exerts pressure on the springs and the top pins to keep them inside the cylin der The top pins in turn press down on the bottom pins Ok PIN TUMBLER CYLINDER OT AUP RUA Notice that when there is no key in the plug the top pins rest halfway between the plug and the cylinder preventing the plug from rotating inside the cylinder The plug is locked into place 22 FIGURE 24 Top Pin and Bottom Pin for a Pin Tumbler Lock FIGURE 25 Anti Pick Pins Lock Mechanisms Pins and Key Cut Depths To the average person a pin may be a piece of jewelry or something to knock over in a bowling alley To a locksmith however p
10. of the sidebar slide into the slots of the lower pins This double action allows the plug to turn FIGURE 34 This type of mechanism uses a SPRINGS sidebar in the plug to PIN HOLES add security SIDEBAR 32 FIGURE 35 A split key requires two people to operate it FIGURE 36 This Schlage Primus key contains two rows of bitting to operate the two mechanisms inside the lock Lock Mechanisms Split Keys Some manufacturers provide a security option with their locks known as the split key Figure 35 Two peo ple are required to open the lock each is given half of the key When two people are needed to open a lock unwanted single party access to the lock is effectively ruled out Multiple Locking Mechanisms The Schlage company manufactures a high security lock the Primus that contains two pin tumbler mechanisms inside Both mechanisms are operated simultaneously by one key However the patented key is specially cut to operate both mechanisms The key contains two rows of bitting Figure 36 SIDE MILLING Anti Wrenching Pins Some lock manufacturers install anti wrenching pins in their locksets Figure 37 An anti wrenching pin acts as an anchor embedded in the door resisting attempts to wrench the cylinder loose Lock Mechanisms FIGURE 37 An anti wrenching pin anchors a lock cylinder to a door preventing it from being wrenched or pried loose 33 LOCK CYLINDER ANTI WRECHING PIN
11. step by step instructions you ll learn how to install a variety of lock ing devices the same locks you ll be installing profitably every day in your professional career Enjoy your continuing studies
12. the combination lock let s take a look at another type of keyless lock the electric lock mechanism Note We ll be dis cussing the use of combination locks in much more detail later in your study unit on safes and vaults 44 Lock Mechanisms ELECTRIC LOCK MECHANISMS Applications Operation Electric locks are used widely by many types of businesses hospitals and industries These keyless locks can be used on rear or side entries of a business to allow employees to enter and exit the building Some homes and apartments have key less entry systems to eliminate the need for keys Most modern hotels use electric locks for entry doors and or keyless electric locks for the actual room doors In addition many of the hotel s interior doors may be held open using electric locks Then if a fire is sensed by the alarm system these doors close to prevent the fire from spreading The simplest type of electric lock consists of a solenoid type plunger that engages in a strike in the door or door jamb When an electrical current is applied to the plunger magnetic force pulls it out of the strike opening the door Another type of electric lock is operated by remote control These are often mortised or key in knob locksets and they re controlled re motely using push buttons or keyed switches Keypad or card reading keyless entry systems are another popular choice Finally the electromagnetic lock consists of a powerful electro magn
13. we ll examine each of these different mechanisms in detail We ll look at how they re constructed and how they operate then we ll examine simple repair techniques for each type Let s start by turning our attention to key operated lock mechanisms Lock Mechanisms 3 KEY O PERA TED LOCK MECHANISMS How Key Operated Mechanisms Work A key operated lock mechanism is simply any type of lock that s opened and closed by inserting and turning a key Remember as we discussed in Study Unit 2 not all locks are opened by a key Some locks are opened by dialing a number combination and some contain electrically operated switches However key operated locks are the most common and familiar to us Key operated locks are found in residential doors cars and padlocks The four most common types of key operated lock mechanisms are the warded mechanism the lever tumbler mechanism the disk tumbler or wafer mechanism and the pin tumbler mechanism We ll discuss each in turn now The Warded Mechanism The word ward means to guard or guard against thus we may ward off a cold by taking vitamin C or a bowl of chicken soup Similarly a warden is a prison guard In locksmithing terms a ward is a metal barrier inside a lock mechanism that prevents just any key from opening the lock The ward en sures that only the proper key will engage the mechanism and open the lock The right key contains cuts that exactly match the shape of the
14. D tubular key 16 If you attempt to move anti pick pins with a lockpick they ll A lift up easily to the shearline B cause the top pins and springs to pop out of the cylinder D cause the lockpick to become wedged inside the cylinder 17 Which of the following lock types is generally the easiest to disassemble A Pin tumbler C Disk tumbler B Lever tumbler 18 When an electric lock s pushbutton is pressed what happens A The electrical circuit is completed and an alarm bell sounds B The coilis See causing a powerful magnet to hold the door shut D The coil attracts a plunger that locks the door 19 Which of the following is used to service an interchangeable core A A change key B A bitkey D A flat key 58 Examination 20 A combination lock will open when B the first number in the combination is dialed C all of its wards have been bypassed by the key D a small hole is drilled in the back of its case Lock Mechanisms 59 COMING ATIRACTIONS Now that you ve completed Study Unit 4 your next information packed study unit is just around the corner Study Unit 5 is entitled Residential Locks and is designed to introduce you to the many door and window locks you ll see in your career as a locksmith The most important career topics you ll learn about are the construction and operation of door locks and the practical installation of door locks With the help of many illustrations and easy to follow
15. Professional Locksmith Study Unit 4 Lock Mechanisms DRAFT This sneak preview of your study material has been prepared in advance of the book s actual online release iii O RC Welcome to Study Unit 4 of your Professional Locksmith course In your last study unit you learned all about keys and how to identify them Now in this study unit you ll begin learning about lock mechanisms in depth A lock mechanism is the internal assembly of a lock that makes it work You ll be learning about a variety of lock mechanisms including key operated combi nation and electric types With the assistance of plenty of detailed diagrams and drawings you ll be able to look at the insides of locks You ll discover how these locks are constructed and how they work Then when you ve gained a solid foundation of knowledge about lock mechanisms you ll learn what types of problems these locks are likely to have and what services locksmiths will need to perform We ll explain how to completely disassemble and re assemble various lock mechanisms Finally we ll tell you how to perform simple servicing cleaning and lubrication on lock mechanisms When you complete this study unit you ll be able to e Name the four basic key operated lock mechanisms e Identify the basic types of key operated lock mechanisms by visual inspection e Name the principal parts of each lock type e Explain in simple language how different types of lock mechanisms work e Cle
16. This is because warded locks aren t nearly as secure as pin tumbler locks since the warded lock has a simple mechanism and the keyhole is large enough to view most of the lock s inside 48 Tl Lock Mechanisms Lever tumbler lock mechanisms are used on school lockers cash boxes suitcases mailboxes and safe deposit boxes The slim flat design of the lever lock is more appropriate for these applications than a cylinder type lock Modern lever tumbler locks almost always use flat keys The lever tumbler mechanism may contain from one to six teen lever tumblers depending on the security of the lock Each lever tumbler is a flat metal plate held in place by spring pressure When the key is inserted the lever tumblers are lifted and aligned inside the lock allowing the lock to open The disk tumbler mechanism also called the wafer tumbler mecha nism is commonly used in automobile doors desks and cabi nets and vending machines The main components of a disk tumbler lock are the shell the plug the disks and the springs The disks or wafers are small flat rectangular pieces of steel each containing a slot or hole For most disk locks the disks come in five different slot arrangements The location of the slot in each disk will determine the key cut depth needed A disk tumbler lock s plug will contain an arrangement of any of these five disks any one of the disks may appear more than once as well The arrangement of t
17. an lubricate and perform simple maintenance on locks e Disassemble and reassemble each type of lock as needed for servicing e List the strong and weak points of each type of mechanism e Explain how high security locks function e Explain how combination entry locks work Uu ie en MON Sa E ere ee ee E E 1 What isa Lock Mechanism Locks vs Lock Mechanisms KEY OPERATED LOCK MECHANISMS 2 2082 nae 3 How Key Operated Mechanisms Work The Warded Mechanism The Lever Tumbler Mechanism The Disk or Wafer Tumbler Mechanism The Pin Tumbler Mechanism High Sec urity Lock Mechanisms Interchangeable Cores Key Operated Padlocks COMBINATION LOCK MECHANISMS 39 Introduction Operation Disassembly Combination Entry Locks ELECTRIC LOCK MECHANISMS 0 28880 neue 4A Applications Operation THE KEY O SUCCESS EC RE ER E E 47 KEY POINTS TO REMEMBER e 47 LOCKING ITUP ANSWERS 12 ee ee ee 53 EXAMINATION con cc 8 be we ee ee ee ee 55 Do You Know Whatis the mostimportant component ofa combination lock Whatare the major parts of a padlock Whatis a ward In these pages you ll find the answers to these and many more questions about lock mechanisms INTRODUCTION What is a Lock Mechanism A lock mechanism is the assembly of parts inside a lock that makes it work In most common locks the locking mecha nism holds or moves a latch bolt or shackle into the locked or unlocked position Due to the m
18. ant to keep the warded lock for its quaint appearance You may also be called upon to repair small warded locks in antique furniture chests cabinets clocks trunks and so on One good suggestion is to keep any old lock parts and any old bit and barrel keys you can find at junk shops yard sales and so on Since these parts and keys aren t widely manufactured anymore keep them on hand for repairs One of the most common causes of warded lock failure is the buildup of dust and debris inside the lock Paint is one of the biggest offenders Repeated painting of a door over the years can leave a warded lock clogged and can make it impossible to insert or turn the key In such a case you ll need to open up the lock to clean it lubricate it or replace worn parts The warded lock is the easiest to disassemble of all the lock types we ll look at Sim ply remove the screws on the cover plate and the guts are exposed After removing the cover plate replace any rusted or worn parts Then use a wire brush to clean dirt and old paint away from the affected lock parts Unless absolutely nec essary stay away from commercial paint removers they tend to attract lint after use Next use a commercial lubricant such as WD 40 never oil we ll explain why later to lubricate the lock You can apply it using the spray assembly attached to the can Lock Mechanisms Locking It Up 1 At the end of each section in your Professio
19. any types of lock designs there are many different types of locking mechanisms For example a door lock contains a mechanism to operate a latch or bolt The latch or bolt is the part that extends into the strike anchoring the door to the door frame When the bolt is thrown it moves into the strike and locks the door when the bolt is retracted back out of the strike the door is free to open FIGURE 1 This figure Figure 1 shows a bolt in the BOLT THROWN thrown position 2 Lock Mechanisms FIGURE 2 A padlock mechanism holds the SHACKLE IS HELD shackle inside the lock INSIDE SHELL HERE case or shell In contrast a padlock contains a mechanism that holds the shackle in the case or shell of the lock or that allows the shackle to release Figure 2 Locks vs Lock Mechanisms It s important for you to note the difference between a lock and a lock mechanism The word lock is a general term that refers to any device installed or attached to improve security A padlock a door lock a car ignition lock all of these are locks A lock mechanism is the inside structure of a lock For example a door lock could contain a warded mechanism pin tumbler mechanism or a disk tumbler mechanism depend ing on how it was made For our study purposes all lock mechanisms can be divided into three basic types key operated lock mechanisms combination lock mechanisms and electric lock mechanisms In this study unit
20. assembly Lock Mechanisms 29 Locking It Up 3 Indicate which of the following are True or False 1 A pin tumbler lock requires a special barrel key to open it The top pins in a pin tumbler lock are all different sizes The bottom pins in a pin tumbler lock are the same size A plug follower is a tool used to clean a pin tumbler lock Pin tumbler lock mechanisms can only be used in padlocks The main parts of a pin tumbler lock are the cylinder the plug the top pins the bottom pins and the lever tumblers The pin tumbler lock is rapidly being replaced by the warded lock A pin tumbler lock can t be opened with a key until all the pins have been aligned along the shearline Check your answers with those on page 53 30 Lock Mechanisms High Security Lock Mechanisms FIGURE 32 This high security lock contains three sets of pins The term high security lock can refer to any one of a variety of locking devices High security locks contain mechanisms that make them especially resistant to picking and forced entry A number of lock manufacturers include a high security line in their catalogs Medeco Security Locks Lori Corporation Kaba and Schlage Lock Company are among the best known of the many manufacturers that do so Most of the high security locks manufactured by these companies contain pin tumbler mechanisms As such they function basically in the same fashion as any pin tumbler lock a
21. d on the lock each of the three wheels will line up with their gates open to the locking pawl Since the locking pawl is free to pivot it will enter the gates on the three tumblers and open the shackle of the lock LOCKING LOCKING DOG TUMBLER GATE Some combination locks carry code numbers stamped on their cases A locksmith can discover the combination by looking up this number in one of the code books available only to professional locksmiths A slightly different model of combination padlock the Sesa mee padlock is shown in Figure 44 Note that this lock has four numbered dials on the bottom of the lock instead of the face One of the most useful features of this lock is that the user can change the combination at will To do so a special key called a change key is inserted into the shackle hole and a new four digit combination rotated into place Note Don t confuse this combination change key with the change key of a master key system 42 FIGURE 44 Sesamee Padlock Disassembly Lock Mechanisms Most combination padlocks can t be disassembled without spending an enormous amount of time and effort to do so If the lock is inexpensive it s generally replaced rather than re FIGURE 45 Drill a small hole as shown here to DRILL HOLE see the wheels inside a HERE combination lock paired However you can expect to meet customers who have lost the combination to a padlock In such a situation you may
22. door is now effectively locked Now look at the lock interior shown in Figure 4 This lock contains several complex wards The key for this lock was elabo rately cut to clear the obstructions caused by the wards Some locks have wards on the exterior of their keyways These wards are called case wards Case wards add a little security to a lock since an additional cut must be made on a key just to allow it to slide into the keyway Figure 5 Lock Mechanisms FIGURE 5 Case wards in the keyway of a warded lock add a little security A skeleton key is a key that has been ground down to make it very thin Figure 6 The wards of a warded lock are easily bypassed using a skeleton key For this reason warded locks are not recommended in circumstances where a high degree of security is desired Warded Mortise Locks and Warded Rim Locks The warded door lock in Figure 7B is called a warded mortise lock because it is installed in a recess in a door called a mortise By comparison the warded rim lock in Figure 7A is surface mounted on rather than in the door Figure 8 shows the interior mechanism of a typical warded rim lock Note that the lock contains two bolts a key operated deadbolt and a latch bolt The latch is operated by turning the door knob The latch fits securely into a strike the metal plate recessed in the door jamb When the latch is in place FIGURE 6 A skeleton key is design
23. e two tangs at the top of the plug when rotated cause the locking mechanism to retract This action causes the shackle to raise under spring pressure No key is required to lock the pad lock Finger pressure is sufficient to return the shackle to the case where the bolts catch the notch and secure it Another type of key operated padlock is the warded padlock A warded padlock is constructed from many flat layers of metal The flat layers are then stacked up and laminated together to form the body of the lock Small cuts are made in some of the layers to create wards in the lock body When all the layers are 50 TT Lock Mechanisms stacked up the key will need to be cut to correspond to the lock s wards A commercial lubricant such as WD 40 never oil should be used to lubricate lock parts Combination lock mechanisms are used in many types of pad locks door entry systems safes and vaults The combination is a series of numbers that s dialed to open the lock The dial is anumbered knob on the outside of the lock which is used to dial the combination The dial is turned clockwise and coun terclockwise to reach the numbers in the combination As the dial is turned the wheels inside are aligned Each time a cor rect number from the combination is dialed another wheel clicks into place When all the numbers have been dialed the wheels will be completely aligned freeing the lock to open The pushbutton combination lock
24. e variation of the disk tumbler mechanism is the cam lock shown in Figure 19 Cam locks are used extensively on cabi net doors and desk drawers In this kind of lock a moveable cam is at tached to the rear of the lock The cam is a flat piece of metal that ro tates when the key is turned in the lock The cam cre ates a physical bar rier that prevents a door or drawer from being pulled open When the cam is turned into the lock position the cam will hold the door or drawer in place When the cam is turned to the unlock position the door or drawer will be free to open Lock Mechanisms FIGURE 20 A hole has been drilled in this disk tumbler lock to allow access fo the retaining Clip 17 Disassembly Disk locks may need to be disassembled for cleaning repair or rekeying Some disk tumbler locks are easy to take apart others are not it depends on the method used to hold the plug inside the shell Some plugs are held with a screw in retaining plate others must be drilled to access the internal retaining clip In the lock shown in Figure 20 a hole has been drilled in the shell to allow access to the retaining clip that holds the plug in place On some disk tumbler locks this hole may al ready be present HOLE DRILLED To remove the plug from such a lock insert a small tool such as a lock pick or thin awl into the drilled hole By applying pressure the retaining clip for the plug can be
25. eaning solutions are available from locksmith supply houses and hardware stores If you wish you can also use electrical spray cleaners such as those used on volume controls and other electronic components A good cleaning solution should flush any dirt and dust from the lock It s a good idea to lightly lubricate the lock with a commercial lubricant after cleaning Never use oil grease or any type of mineral or paraffin base lubricants These types of lubricants will collect dust and dirt over time and eventually turn into a paste inside the lock This paste will cause the lock to malfunction Lock Mechanisms 19 Locking It Up 2 Indicate whether each of the following statements is True or False 1 Modern lever tumbler locks almost always use bit keys 2 The disk tumbler mechanism is also called the wafer tumbler mechanism 3 A disk tumbler lock s springs typically contain an arrangement of five disks 4 Lever lock mechanisms are commonly used as ignition door and trunk or rear hatch locks for General Motors automobiles and light trucks 5 When the side bar wafer lock mechanism is locked the side bar extends into a special slot inside the shell as a result the plug is held securely in place 6 Cam locks are used extensively on home entry doors and car ignitions 7 All disk tumbler locks are easy to take apart 8 It s generally cheaper to replace a malfunctioning disk tumbler lock than to repair it
26. ed to bypass the wards in a warded lock the door will be held closed but not locked since no key is required to move it When the inside latch 6 Lock Mechanisms FIGURE 7 Part A of this illustration shows a warded rim lock Part B shows a warded mortise lock button is pressed down though it does prevent the latch bolt from being released by anyone outside the door The deadbolt is operated by a key or by turning a turnpiece inside the door The door is truly locked when the deadbolt is thrown INSIDE INSIDE LATCH LOCK LATCH SPRING DEADBOLT LATCH BOLT SPRING FIGURE 8 Interior of a KEY HOLE Warded Rim Lock Lock Mechanisms FIGURE 9 Key picks like the ones shown here are useful for opening warded locks Advantages and Disadvantages of the Warded Lock Warded locks aren t generally used on today s exterior doors They have been replaced by pin tumbler or disk tumbler locks in most cases This is because warded locks aren t nearly as se cure as pin tumbler locks which we ll discuss shortly Why isn t the warded lock secure enough Well a lock s security depends on the following two things 1 The complexity of its internal mechanism 2 The ease of looking into the lock to see the mechanism In both of these cases the warded lock offers little protection Its mechanism is simple and the keyhole is large enough to view most of the inside of the lock Because the keyway is so large it
27. er If the spring retainer was damaged during removal replace it with a new one Now let s look at a different method of disassembling a pin tumbler cylinder Since most pin tumbler locks don t contain spring retainers it will be necessary to use this second method in most cases Let s examine a pin tumbler mortise cylinder Figure 30 You may remember from an earlier study unit that a mortise cylinder is installed directly in the surface of a door This type of lock doesn t have a spring retainer In order to gain access to the pins and springs inside the mechanism it will be necessary to remove the plug from the cylinder To re move the plug the retainer plate must be removed first The plug retainer plate is held by two small machine screws RETAINER BACK VIEW PLATE SCREWS Remove the retainer plate using a small screwdriver Now once the retainer plate has been removed you could simply insert the key turn it one quarter of a turn and withdraw the plug from the lock cylinder BUT WAIT If you do that all the top pins and springs will pop free of the lock And while these pins and springs can be replaced with a tweezers it s not an easy job For this reason the proper way to remove the plug is to use a plug follower A plug follower is a wood metal or plastic dowel that holds the top pins and springs in place in the cylinder when you withdraw the plug To use the follower Lock Mechanisms FIGURE 31 T
28. ers inside these locks are small flat rectangular pieces of steel each containing a slot or hole The key will be inserted into these slots to operate the lock 14 FIGURE 15 The five different sizes of discs in a disk tumbler lock are shown here FIGURE 16 This cutaway side view shows a key inserted in a disk tumbler plug The disks have been pulled into alignment by the key freeing the plug to turn Lock Mechanisms For most disk locks the disks come in five different slot ar rangements Figure 15 The location of the slot in each disk will determine the key cut depth needed In Figure 15 note that the position of the slot in each disk is a little different The distance from the top of each disk varies You may also notice that each disk has a number stamped on it This number identifies the type of disk you re working with A disk tumbler lock s plug will contain an arrange ment of any of these five disks any one of the disks may appear more than once as well While the five disk tumblers inside the disk tumbler lock plug are the same height and width the rectangular cuts in the disks vary in terms of their position on the disks The key has five cuts that correspond exactly to these tumbler cuts The arrange ment of the disks forms each lock s individual combination The plug is held inside the shell The shell contains an upper and a lower slot The disks or wafers inside the plug stick
29. et and a steel plate that can hold a door against 2 000 or more pounds of force In the simplest electric lock circuit a single switch or push button and an electric lock is used to protect one door The power supply for this electric lock consists of a fuse and a transformer One side of the transformer connects to the electric lock s coil and the opposite side of the transformer connects to a pushbutton switch When the pushbutton is pressed the circuit is completed and the coil is energized When the coil is energized the coil attracts a plunger that allows the door to open More than one electric lock can be linked to one circuit and con trolled with a single switch In such a system both locks oper ate when the pushbutton is depressed The current flow in this Lock Mechanisms 45 circuit doubles since two loads are connected across the power supply Two of the electric circuit devices we ve been discussing the transformer and the electric lock coil use electromagnetism to operate Electromagnetism is created by a magnetic field that surrounds a conductor when electric current flows through it The magnetic field that surrounds a wire is very small If you could place a compass very close to the wire you would see the needle of the compass deflect slightly This small deflec tion serves no real purpose in pulling back an electric lock solenoid However if you loop the wire many times around a core the magnetic f
30. eventing the plug from rotating in side the cylinder When the proper key is inserted in the lock the pins are lifted to the height necessary to align them along the shearline free ing the plug to turn By changing the heights and placement of pins in the lock plug the locksmith can make a different key to operate the lock This process is called rekeying High security locks are locking devices that are especially resistant to picking and forced entry Most high security locks contain complex or modified pin tumbler mechanisms For ex ample some high security mechanisms hold more than one set of pins The pins enter the lock cylinder at an angle and the key must be specially cut to accept the pins at that angle Some other features manufacturers add to their high security mechanisms are sidebars split keys multiple locking mecha nisms anti wrenching pins and high security strikes Interchangeable or removable cores are specially designed lock cylinders that can be removed from a door lockset without disassembling the lock or door knob To remove the core a special key called a control key is inserted and turned and the core is then withdrawn Most of these locks are used in com mercial installations Padlocks are another common type of key operated lock Remember that the main parts of a padlock are the shackle the shell and the tangs The shackle is held in two locations by the locking mechanism near the top of the lock Th
31. given a simple three digit combination Now let s examine the operation of the combination lock mechanism First the combination is a series of numbers usu ally three numbers that is dialed to open the lock Typically the combination is set at the factory However a locksmith can change a padlock combination at a customer s request Inside the lock the main components are the wheels or tum blers Outside the lock has one or more dials The internal components of a simple combination padlock are shown in Figure 42 This lock contains three wheels and a dial on its face The dial is anumbered knob on the outside of the lock which is used to dial the combination It can be rotated to the left and 40 FIGURE 42 This combination lock mechanism contains three wheels and a numbered dial on its TENSION face SPRING TUMBLER TUMBLER TUMBLER 2 3 Lock Mechanisms right The numbers on its face start at 0 and are read clock wise Some locks read from 0 to 50 some read from 0 to 100 Locks with numbers up to 100 usually have a little more security than ones reading up to only 50 When a combination lock is locked the wheels are posi tioned in random relationship to each other However if the three wheels are moved in such a way that the wheels are caused to align the lock mechanism will be released To align the wheels the dial is turned clockwise and counterclockwise to reach the numbers in the
32. h disk or wafer has a V shaped notch on one side These wafers may be identified by a number one through five stamped on the wafer These numbers refer to the heights of the position of the V shaped notch You ll remember from our previous discussion that a regular disk lock opens when the disks disengage from a slot in the shell allowing the plug to turn In contrast in a side bar wafer lock the disks release a side bar that disengages from a slot in the shell FIGURE 17 This figure shows the five types of wafers or disks you ll see inside a side bar wa fer lock Note the V shaped notches in the sides of the wafers 16 FIGURE 18 1n this cutaway view of a side bar wafer lock you can see how the disks must be aligned to allow the side bar to disengage from the shell FIGURE 19 This illustration shows a typical cam lock Lock Mechanisms When the side bar SPRING CYLINDER wafer mechanism is SHELL locked the side bar extends into a spe cial slot inside the shell as a result the plug is held securely in place As the key enters the plug the key pushes the disks upward causing the side bar to fall into the group of V shaped notches on the side of the disks The side bar is now clear of the slot and the plug is free to turn with the key The disks can only be aligned by the proper key The operation of a typical side bar wafer arrangement is shown in Figure 18 The Cam Lock Mechanism On
33. he disks forms each lock s individual combination The disks are slotted for key entry When the proper key is inserted into the lock the disks are pulled away from the lock shell and centered in the plug This action frees the plug from the shell and allows the plug to turn with the key A side bar wafer lock is a variation of the disk tumbler lock that is widely used for ignition door and trunk or rear hatch locks for General Motors automobiles Another variation of the disk tumbler mechanism is the cam lock Cam locks are used extensively on cabinet doors and desk drawers In this kind of lock a moveable cam is attached to the rear of the lock The cam rotates when the key is turned in the lock creating a physical barrier that prevents a door or drawer from being pulled open The pin tumbler lock is the most secure and widely used lock today This type of lock is very popular in home entry locks padlocks and other types of locking devices Pin tumbler lock mechanisms are always operated with cylinder keys The pin tumbler mechanism is relatively easy to disassemble and repair Lock Mechanisms 49 See A pin tumbler mechanism is contained within a device called a cylinder A pin tumbler cylinder holds the plug which is a small tube containing the bottom pins The heights of the bottom pins correspond to the cut depths in the key The top pins are all the same height and rest halfway between the plug and the cylinder pr
34. he interior of a lever tumbler lock mechanism 11 COVER BOSS ___ TRUNNION LEVER TUMBLER DOP LEVER TUMBLER MIDDLE LEVER TUMBLER BOTTOM Pos BOU The key enters through the cover boss and trunnion When the key is inserted the key s cuts will engage the saddle of each lever tumbler The saddle must be raised enough to allow the post that is attached to the bolt to slide into the rear trap When this action occurs the bolt will slide out of the jamb of the door opening the door In some lever tumbler locks you may see different colored levers The color of the lever will identify the trap to saddle distance Also in some lever tumbler locks the levers them selves will be of different thicknesses Here the thicker the lever the greater the distance is between the bottom of the saddle and the center of the trap 12 Lock Mechanisms FIGURE 12 This illustration shows the GATING parts of one lever Ria SLOT GATE Ge tumbler OR FENCE N SPRING Disassembly and Servicing Lever tumbler locks that have been riveted or spot welded are generally very inexpensive and aren t worth the work required to disassemble and reassemble them Instead they should just be replaced Other types of lever locks can be opened either by removing the cover screws or by prying the cover off according to how the cover is attached Carefully remove the trunnion and then the lever tumblers in o
35. ields would add together increasing the overall field strength The fields from the many turns of wire are concentrated in the core when the wire coil is energized In fact the coil has enough strength to pull the plunger out of the strike box on a typical electric door lock This introductory information to electric locks should be enough to familiarize you with their operation However note that we ll be discussing these locks as well as electronic security systems in much greater detail in a later study unit 46 Lock Mechanisms Locking It Up 5 Indicate whether each of the following statements is True or False 1 Only one electric lock can be connected to a circuit 2 A special key called a change key is used to alter the combination of a Sesamee padlock 3 The main components in a combination lock are the dials 4 Once a lock s combination has been set at the factory it can never be changed 5 Pushbutton combination locks are very difficult to install and operate 6 A padlock combination usually consists of three numbers Check your answers with those on page 54 Lock Mechanisms 47 THE KEY TO SUCCESS Since the beginning of this study unit you ve learned many of the important concepts and terms relating to lock mecha nisms You ve learned how lock mechanisms work in detail You ve also learned how to disassemble and service many lock mechanisms Think about how important this valuable knowledge wi
36. ike a locksmith This is exactly what a locksmith does to rekey a lock By changing the heights and placement of pins in the lock plug the locksmith can make a different key operate the lock What kinds of repairs are made on a pin tumbler lock All kinds The pin tumbler mechanism is generally more expen sive than other lock mechanisms and it s also relatively easy to disassemble and repair For these reasons pin tumbler mechanisms are often repaired instead of replaced Lock Mechanisms FIGURE 29 Many locksmiths use an otoscope to view the insides of locks 25 Typical problems with a pin tumbler lock include worn pins and worn or broken springs Because the pin tumbler mecha nism is more complex than the other mechanisms we ve dis cussed it s more vulnerable to dirt and grime The small parts in a pin tumbler lock can easily freeze up from a buildup of dirt or a lack of lubrication In addition under the right weather conditions a pin tumbler door lock can freeze from moisture intrusion or corrosion To perform repairs on a lock or to rekey it you ll need to dis assemble the lock While there are many different types and sizes of pin tumbler locks there are some general disassem bly techniques that can be applied to most Consult the lock manufacturer s instructions for guidance whenever they re available Let s start by looking at a typical pin tumbler door lock Before you begin note that a bright ligh
37. in interchangeable cores Choosing the Right Padlock What s the best padlock to buy As a locksmith you ll hear that question repeatedly and there s no easy answer Nevertheless since you ll be expected to come up with an answer do so by Lock Mechanisms 34 reviewing with the customer the following considerations purpose location and frequency of use Purpose What is the padlock going to be used to lock A child s bicycle or school locker will obviously require much less security than the door to a garage or boathouse Location Will the lock be used indoors or outdoors An outdoor lock will naturally take more abuse from the weather than an indoor unit A shed door that is covered in snow four or five months of the year presents a real problem for a cheap padlock Urge the customer to consider any unusual circumstances due to location moisture sand dust extreme sunlight and so on Frequency of Use The price of a padlock is to a large extent dependent on its durability If the lock is to be operated sev eral times a day consider a better model 38 Lock Mechanisms Locking It Up 4 Fill in the blanks in each of the following statements 1 A special key called a key is used to remove an interchange able core 2 A _ key requires two people to open a lock Each person is given half of the key 3 A special type of key that contains two rows of bitting is used in the lock 4 A an acts as an
38. ins are very important lock components since the movement of the pins controls the turning of the lock plug Figure 24 shows an enlarged view of a top pin and bottom pin A top pin is flat on both ends A bottom pin however is slightly rounded at the end to make the insertion of a key smoother R TOP BOTTOM PIN PIN Some pin tumbler locks contain pins that make the lock harder to pick Anti pick pins are specially formed to jam in side the lock if someone tries to move them with a lockpick ing tool These pins are shaped like mushrooms or spools Figure 25 J3 U MUSHROOM PIN SPOOL PIN If you attempt to move anti pick pins with a lockpick they ll jam between the plug and the cylinder Figure 26 Lock Mechanisms FIGURE 26 If you attempt to lift an anti pick pin witha lockpicking tool the pin will jam between the plug and the cylinder FIGURE 27 The bottom pins in a pin tumbler lock must correspond exactly to the cut depths in the key 23 MUSHROOM PIN SPRING LOWER PIN Ina pin tumbler mechanism the length of the top pins is always the same but the bottom pins vary in length The length of the bottom pins must correspond exactly to the depth of the cuts in the key Figure 27 The deeper the cut in the key the longer the pin Operation To open the pin tumbler mechanism we need to move the bottom pins upward so that they align with the top pins When the correct key is inserted
39. into the plug the bottom pins are lifted The bottom pins press against the top pins forcing them up into the cylinder The bottom pins and the top pins will then line up exactly at the shearline The shearline is the straight line formed between the top pins and bottom pins 24 FIGURE 28 The wrong key was inserted in this lock causing the pins to be misaligned at the shearline the plug isn t free fo turn Lock Mechanisms When the top and bottom pins have been aligned exactly at the shearline the shearline is free of obstructions and the key can be turned When the key is turned the plug will turn freely with it allowing the lock to open Note that a very thin space exists between the plug and the cylinder This is because if the plug were held too tightly in the cylinder it couldn t turn to open the lock Refer back to Figure 23 for a visual aid to understanding this process Now if the wrong key is inserted in this lock Figure 28 the pins would not line up exactly at the shearline Some of the top pins will be above the shearline and some will be below it This misplacement of the pins will keep the plug from turning inside the cylinder PINS LIFTED UP TO INCORRECT HEIGHTS Disassembly Has it crossed your mind that you could make a wrong key fit in the lock simply by changing the heights of the bottom pins Or you could switch the locations of the bottom pins If so you re starting to think l
40. is a popular type of combina tion entry lock that is especially common in hotels or other facilities where many strangers come and go at will Instead of having to supply each person with a key a three number combination is supplied The combination can be changed quickly and easily to maintain security Electric locks are used by many types of businesses hospitals and industries In the simplest electric lock circuit a single switch or pushbutton and an electric lock is used to protect one door The power supply for this electric lock consists of a fuse and a transformer When a pushbutton is pressed the circuit is completed and the coil is energized When the coil is energized the coil attracts a plunger that allows the door to open Lock Mechanisms 51 Do You Know Now Below are the answers to the questions asked at the beginning of this study unit Whatis the most important component ofa combination lock The wheels ortumblers are the most important components of the combination lock mechanism Whatare the major parts of a padlock The major parts of a padlock are the shackle the case or shell and the tangs Whatis a ward A ward isa metal bamer inside a warded lock that obstructs any key but the properone 2 NOTES Lock Mechanisms Oo N A aA RA Q N e EE gt Oo oo N Oh D P V N Be ao o vd mm d mm d Mm Bit barrel padlock ward case wards Skeleton key rim lock mechanism
41. key enters the plug and elevates pins of various heights to the shearline after which the lock can be opened However in a high security lock the pin tumbler mechanism is much more complex than in an ordinary lock It usually contains two or more sets of top and bottom pins For example in the Kaba Gemini brand high security mechanism the lock plug holds three sets of pins The pins enter the lock cylinder at an angle and the key must be specially cut to accept the pins at that angle Figure 32 shows an end view of this type of mechanism Note the three sets of pins and the angled depressions needed in the key to make it fit in the lock Figure 33 shows an exploded view of the lock plug Note how the pins and springs are inserted into the plug KEY INSERTED IN LOCK Now let s look at some other special features manufacturers put into their high security locks Lock Mechanisms 31 SPRINGS ie BOTTOM PINS WS oe EINE aaa a s gt X e a i gt D gt a S ki D D BOTTOM PINS SPRINGS FIGURE 33 This illustration shows an exploded view of a high security lock plug Sidebars Medeco brand high security locks incorporate a sidebar into the lock plug to increase security As Figure 34 shows the sidebar has five legs that correspond to five ver tical slots on the facing bottom pins When the proper key is inserted the pins are raised to the shearline and also rotated so that the legs
42. ll be to your future career as a locksmith You ve already mastered many of the basic topics you ll need to become qualified as a professional locksmith Be proud of your scholastic achievements and continue to plan for your future Now when you re ready read through the Key Points to Re member that follow When you ve reviewed the material and feel you know it well proceed to the examination for this study unit Good Luck KEY POINTS TO REMEMBER gt A lock mechanism is the assembly of parts inside a lock that makes it work All lock mechanisms can be divided into three basic types key operated lock mechanisms combination lock mechanisms and electric lock mechanisms A key operated lock mechanism is simply any type of lock that s opened and closed by inserting and turning a key Key operated locks are found in residential doors cars and padlocks gt gt The warded lock mechanism is the oldest type still in use today Bit keys and barrel keys are used to open warded door and cabinet locks The word ward means to guard or guard against In locksmithing terms a ward is a metal barrier inside a lock mechanism that ensures that only the proper key will engage the mechanism and open the lock The right key contains cuts that exactly match the shape of the wards inside the lock Gr Warded locks aren t generally used on today s exterior doors They have been replaced by pin tumbler or disk tumbler locks in most cases
43. nal Locksmith texts you ll be asked to pause and check your understanding of what you ve just read by completing a Locking It Up quiz Writing the answers to these questions will help you review what you ve studied so far Please com plete Locking It Up 1 now Fill in the blanks in the following statements 1 keys and keys are used to open warded door and cabinet locks 2 A is the assembly of parts inside a lock that makes it work 3 A _ contains a mechanism that holds or releases a shackle in the case or shell of the lock 4 A _ is simply any type of lock that s opened and closed by in serting and turning a key 5 The word means to guard or guard against 6 Wards on the exterior of the keyway of a lock are called 7 A _ is a key that has been ground down to bypass the wards in a warded lock 8 A _ lock is mounted on the surface of a door Check your answers with those on page 53 10 Lock Mechanisms The Lever Tumbler Mechanism FIGURE 10 A Lever Tumbler Lock Figure 10 shows an exterior view of a typical lever tumbler lock Lever tumbler locks are used on school lockers cash boxes suitcases mailboxes and safe deposit boxes The slim flat de sign of the lever tumbler lock is more appropriate for these ap plications than a cylinder ty pe lock Modern lever tumbler locks almost always use flat keys although some European models are operated with bit or barrel keys The average lever lock is only
44. o properly remove a lock plug from a mortise cylinder place a plug follower against the plug and push the plug from the shell ai simply insert the key to its full depth and turn it one quarter of a turn Now place the end of the follower at the rear of the plug Gently withdraw the plug and at the same time push in the follower The follower will take the place of the plug while you re working on the bottom pins The use of a plug follower is shown in Figure 31 oe iil el iz HOLD ON EACH SIDE With the plug out of the cylinder the bottom pins can now be removed from the plug Tip the plug slightly and carefully remove the bottom pins in order with a tweezers Deposit the pins in a pin tray in order If you re only cleaning or lubricat ing the lock you must return the bottom pins to their original positions in the plug otherwise the key won t open the lock when you put it back together If the lock is being rekeyed you can change the positions of the bottom pins or replace them as necessaty To reassemble the lock your first task is to test the arrange ment of the bottom pins in the plug With the plug still out of the cylinder insert the key into the plug Check to make sure that the bottom pins are all lifted exactly to the shearline If any pins fall below or stick out above the shearline you ve made an error somewhere Rearrange the pins as necessary to get them back to their original order This is a
45. ocks Padlocks are a familiar part of our daily lives Many of us be came familiar with padlocks as children using them to secure Lock Mechanisms FIGURE 40 Parts of a Padlock 35 our school lockers and bicycles Adults use padlocks to se cure garages outbuildings toolboxes trunks storage units and just about any other enclosure that offers a hasp to hang a padlock from There are a number of other padlock varieties Some pad locks use a plug as a locking mechanism the plug may hold pins discs or wafers High security padlocks are also avail able These padlocks feature special laminations as well as independent control of the two ends of the shackle We discussed the operation of a padlock in the Practice Exercise for Study Unit 2 Your Papaiz padlock is illustrated again for your ref erence in Figure 40 Remember that the main parts of a padlock are the shackle the shell and the tangs The shackle is held in two locations by the locking mechanism near the top of the lock The two tangs at the top of the plug when rotated cause the locking mechanism to re tract This action causes the shackle to raise under spring pressure SHACKLE SHELL PLUG LOCKING MECHANISM No key is required to lock the padlock Finger pressure is suf ficient to return the shackle to the case where the bolts catch the notch and secure it Warded Padlocks Warded padlocks are constructed a little differently from
46. out a little and fit into the lower slot in the shell The disks or wafers are pressed into the slot by means of small springs This keeps the plug from turning inside the shell when there s no key in the lock The disks are slotted for key entry When the proper key is in serted into the lock the disks are pulled away from the slot in the shell and cen tered in the plug This action frees the plug from the shell and allows the plug to turn with the key Figure 16 shows a view of a key in serted in a disk lock LOCKING CAM If an improperly cut key is inserted into the plug one or more of the disks Lock Mechanisms 15 may not be lifted out of the slot in the shell This action will prevent the plug from turning and the lock from opening The Side Bar Wafer Lock Mechanism A side bar wafer lock is a variation of the disk tumbler lock Side bar wafer locks provide a greater degree of security than simple disk tumbler locks because they re extremely difficult to pick Side bar wafer locks will make up a large amount of your locksmithing work This is because they re inexpensive and also because they re widely used for ignition door and trunk or rear hatch locks for General Motors automobiles and light trucks The five types of wafers that you might find inside a side bar wafer lock are shown in Figure 17 The disks in a side bar wafer lock are much like those in a standard disk tumbler lock but with one change eac
47. overs are available through locksmith suppliers With the cover removed begin lifting the six internal springs from the lock with a pair of tweezers Place these springs in your pin tray or other container Ifyou were disassembling the lock for the purpose of rekey ing you would now lift the disks out of the plug and replace them as needed Replace the springs and then insert a new spring retainer cover into the shell Disassembling a Cam Lock To disassemble a cam lock remove the nut lock washer and cam from the back of the lock The core can now be pushed out with finger pressure or eased out using the key Cleaning and Lubricating If a disk or spring has broken inside a disk tumbler lock the lock is sometimes replaced This is because it can be cheaper to replace a malfunctioning disk tumbler lock than to repair it However in many cases a thorough cleaning and lubrica tion can quickly and easily correct many lock problems One of the first things to check when a disk tumbler lock fails is the key When a key gets very worn it may not lift the disks to the proper height keeping the plug from turning Often when a key is excessively worn cutting a new key will correct the problem Many disk tumbler locks fail due to dirt or lack of lubrication particularly car locks which are constantly exposed to the elements Disk tumbler plugs can be cleaned in a safe and non flammable solvent Spray solvents and other types of cl
48. rder Reassemble by reversing the procedure Once the lever tumblers have been removed the exposed base and bolt can be checked for irregularities If you find any foreign matter remove it The most probable cause of trouble in a lever tumbler lock is a broken spring To correct remove the broken spring from the affected lever and replace it The Disk or Wafer Tumbler Mechanism The disk tumbler mechanism also called the wafer tumbler mechanism is commonly used in automobile doors desks and cabinets and vending machines Disk tumbler locks provide much better security than warded or lever tumbler locks Note that while most disk locks are constructed the same way their Lock Mechanisms FIGURE 13 This type of disk tumbler lock is commonly used on desks FIGURE 14 Exploded View of a Disk Tumbler Lock Mechanism 13 outward appear ances may vary de pending on what the lock is used for Figure 13 shows a familiar example of a disk tumbler lock Figure 14 is an ex ploded drawing of the principal parts of a disk tumbler lock The main components of a disk tumbler lock are the shell the plug the disks and the springs Let s examine the disks first CYLINDER SHELL DISK SLOTS RETAINING CLIP ey SEH SPRINGS PLUG i When you first think about a disk tumbler or wafer tumbler lock you may think that the disks within the lock are circu lar However this is not the case The disks or waf
49. slightly more secure than the warded lock however the lever locks used on safe deposit boxes are very secure Lever tumbler locks are available in a wide range of security levels Generally the lever tumbler locks you will encounter will have between two and five lever tum blers within the lock Some high security lever tum bler locks can have as many as sixteen lever tumblers The more tumblers the more difficult it is to invade the lock High security lever tumbler locks are used on some types of bank safe deposit boxes and on some types of public lockers In this section on picking lever tumbler locks we ll look at the medium secu rity lever tumbler locks with two to five lever tumblers Now let s look at the interior of a lever tumbler mechanism Figure 11 to see how it operates This lock mechanism contains three lever tumblers Regardless of the number of tumblers however the operation is essentially the same in all lever tumbler locks Each lever tumbler is a flat metal plate held in place by spring pressure Figure 12 shows the parts of one lever tumbler Taking a close look at these parts will help you understand how the lever tumbler lock operates The lever is the most important part of the lever lock mechanism since its move ment controls the movement of the bolt Other important components of the lever tumbler lock are the gate the post and the saddle Lock Mechanisms FIGURE 11 This figure shows t
50. t is useful for viewing the inside of pin tumbler locks Many locksmiths use lights called otoscopes to look into locks Figure 29 The otoscope is the same tool that a physician uses to look inside patients ears and throats This light uses a halogen bulb and lens to concentrate an extremely bright beam of light into the key way of the lock being picked Some pin tumbler door locks are made with a spring retainer The spring retainer is a small rectangular metal cover that fits over the holes where the pins and springs are dropped into a lock plug If the spring retainer is removed you can gain access to the springs and the pins beneath them To disassemble such a lock simply remove the spring retainer you may need to use a pliers to pinch the retainer to remove it Next block all but one hole in the cylinder and dump out the top and bottom pin from the one open hole Continue this operation until all pins are removed from the lock Set the pins in a pin tray for storage while you work on the lock Keep the 26 FIGURE 30 In this pin tumbler mortise cylinder the plug can be removed after two screws are unscrewed from the shell releasing the retainer plate Lock Mechanisms top pins together and keep the bottom pins in the same order in which you took them out of the lock To reassemble the lock replace the bottom pins in order into the plug holes Then replace the top pins springs and spring retain
51. the warded door lock but the principle of operation is the same A modern warded padlock is constructed from many flat layers of metal The flat layers are then stacked up and laminated together to form the body of the lock Small cuts are made in 36 FIGURE 41 1Interior View of a Warded Padlock Lock Mechanisms some of the layers to tado CN stacked up the key will need to be cut to correspond to the ge create wards in the lock body When all SHACKLE i the layers are BOLTS BoLT lock s wards An in SPRING terior view of a SHACKLE E warded padlock is g shown in Figure 41 When the correct key is inserted in a warded padlock it passes through the wards and can be turned As the key turns it moves the bolts out of the notch and the shackle is forced upward and out of the case by the now relieved pressure of the shackle spring Flat keys are used with warded padlocks Disassembly Since most padlocks are inexpensive they re more often replaced than repaired In addition many inexpensive padlocks and all laminated warded padlocks can t be disas sembled at all Expensive heavy duty high security padlocks on the other hand are well worth disassembly and servicing The manu facturer s instructions will tell you how to disassemble a padlock for example some have special pins or rivets that must be removed to access the locking mechanism In addi tion some high security padlocks conta
52. ver tumbler door lock GRA RES Te aidedp dode 6 Where is a rim lock installed A Ona briefcase or suitcase C On the surface of an automobile door B Ona safety deposit box 7 Wheels are essential to the operation of C a disk tumbler lock B a plug follower D a warded lock 8 An anti wrenching pin is a device that A is found only in warded lock mechanisms C prevents a lock cylinder from being picked D protects a lock cylinder from rust and corrosion 9 A disk tumbler lock may also be called C awarded lock B a lever lock D a high security lock 10 The wards of a warded lock may be bypassed using a A change key C disk tumbler SEN D plug follower 11 A typical combination on a combination lock consists of a series of numbers A two C ten D no Examination 57 12 Which of the following are components of a lever tumbler mechanism B The cover boss the trunnion and the ward C The saddle the top pins and the lever D The trunnion the post and the milling groove 13 Which of the following are components of a pin tumbler mechanism A The top pins the trunnion and the lever C The plug the case ward and the bottom pins B The SE the top pins and the wheels 14 The top pins in a pin tumbler lock mechanism C are all different sizes B are welded together D correspond to the cuts in the key 15 A warded door lock is usually opened with a A cylinder key B flat key
53. very important step If you have made a mistake in replac ing the bottom pins and you replace the plug in the cylinder without first checking the key the plug could lock itself inside the cylinder Once this happens the original key will no longer work and you won t be able to remove the plug again to 28 Lock Mechanisms change the bottom pins One option is to try to pick the lock to get it open again which is extremely time consuming An other option is to shim the cylinder open using a piece of shim stock In most cases this is faster Always remember to test the plug before you put it back in the cylinder Once you ve made sure that the key still works you re ready to reassemble the lock cylinder The plug is reinserted from the front of the cylinder Place the end of the plug at the front of the cylinder so that it touches the plug follower Then gently press the plug into the cylinder and at the same time carefully withdraw the follower The pins should be at a 45 degree angle to the top pins so the cylinder goes in more easily Servicing Cleaning and Repair The disassembled parts of a pin tumbler lock may be cleaned with an application of WD 40 or a similar silicon based solvent In many cases a spray cleaner the kind used on electronic parts and components can be used to remove dirt and grime The parts may then be lightly lubricated with WD 40 and replaced in the lock Never over lubricate the parts before re
54. wards inside the lock The warded lock mechanism is the oldest type still in use to day it was first used by the Romans thousands of years ago Bit keys and barrel keys are used to open warded door and cabinet locks flat keys are used to operate warded padlocks The basic principle behind the warded lock is barrier protection This means that the wards create a physical barrier that must be overcome before the lock can be opened The security of the warded mechanism comes from the type and number of wards it contains A ward is simply a metal ridge inside the lock that creates a barrier to the lock bolt A properly cut key will fit around the wards and be free to turn opening the lock FIGURE 3 This warded mechanism contains two wards FIGURE 4 This complex warded lock contains several wards arranged fo provide extra security for the lock Note the many cuts needed on the key fo allow it to clear the wards Lock Mechanisms A warded lock can contain any number of wards The sim plest type contains only one ward and is called a single warded lock The in terior of a simple warded lock is shown in Figure 3 Note that when the key is inserted the cut corresponds exactly to the place ment of the wards When the proper key enters the keyhole of the unlocked door negotiates the wards and is turned it raises the deadbolt over the obstructions that detain it The deadbolt enters the strike and the
Download Pdf Manuals
Related Search