Home

Installation and Operation Manual - Epic - IronStrike

1. Blower Removal Figure 37 Cassette Screws Figure 38 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 31 32 TROUBLESHOOTING NOTE When troubleshooting the gas control system be sure the external gas shut off valve located at the gas supply inlet is in the ON position IMPORTANT Call your gas supplier or plumber for additional help with any gas control problem Valve system troubleshooting should only be accomplished by a qualified service technician SYMPTOM PROBABLE CAUSE CORRECTIVE ACTION Thin black coating soot forms on the viewing glass logs or firebox Humming or whistling coming from fireplace A change in flame appearance or burner operation Pilot will not light Pilot will not stay lit after carefully following lighting instructions Main burner will not burn Improper log or ember placement Blocked flue Improper air shutter setting Normal operating noise Dirt in burner orifice A change in gas pres sure Improper ember or log placement No gas supplied to unit Air in line Defective igniter no spark at electrode The valve control knob is not turned to pilot and pushed in Pilot flame is not sur rounding thermocouple Thermocouple not generating sufficient voltage Air in gas supply line Pilot has gone out Rocker switch or thermostat wires are
2. 5 Homeowner Attaching Safety In Operation Warnings 6 Installer Attaching Safety In Operation Warnings 7 Appliance Installation Service and Maintenance Notices 8 Appliance Operation 8 Warranty Information 5 5555555555555555555555 5 555 5 6 Important Safety And Warning Information 9 Orifice Size Altitude Adjustment ee 10 Smoke Detectors 10 The Epie Stove iie se oder ra RO 10 Codes and 10 New York City New York MEA 10 Commonwealth Of Massachusetts Requirements 10 Pre Installation 11 13 A E niet 11 Packaging LiSl 1 cerco 11 RATINOS MCI a ce 11 Preparing Your Epic Stove for Installation 12 DIMENSIONS age 12 Clearances to Combustibles 13 LS ET LE TO et 13 17 Trim Installation 13 Firebox SOUP iio cd 14 Firebox Liner Installation 15 Log Set and Ember I
3. 1219mm Max 48 1219mm Min MZ Figure 5 Alcove Dimensions Pipe Clearances All installations using a vertical termination cap must maintain one inch clearance between the direct vent pipe and combustibles For horizontal runs of pipe one inch of clearance to combustibles on the sides and bottom and two inches on the top of the pipe is required See Page 21 for allowable pipe configurations INSTALLATION Install Door Trim Kit Install door trim kit per instructions provided in kit ref form 775291M Figure 6 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 13 14 Firebox Setup Figure 7 Figure 8 Burner Pan Diagram Log Stands Completed Firebox Setup To ensure a proper burn leave a 1 space free of any embers volcanic Do not cover any secondary air holes or gas ports see Burner stone or glowing embers rockwool directly in front ofthe air deflector Pan Diagram above behind this line see Burner Pan Diagram above NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Firebox Liner Kit Installation CAUTION The firebox liner panels are required for your appli ance to function correctly and safely Packaging List Rear brick panel A left brick panel B right brick panel retaining brackets D in flue restrictor bag 1 Remove the firebox liner panels from the box and carefully unwrap them The panels are fragile so handle them with care Remove the bag c
4. CODES AND APPROVALS Certification Gas appliances must be tested and certified by a nationally recognized testing and certification laboratory to ANSI American National Standard Institute gas appliance safety standards This stove has been tested and certified to ANSI 721 88 CSA 2 33 Standard for Vented Gas Fireplace Heater and CGA 2 17 M91 and UL 307B Gas Burning Heating Appliances for Manufactured Mobile Homes in both USA and Canada It has met all necessary ANSI Standards and is fully certified for installa tion in any community If there are any questions or if you need further substantiation either write to or call your IHP dealer If you have further questions please contact IHP Check all local building and safety codes before installation The instal lation instructions and appropriate code requirements must be followed exactly and without compromise In the absence of local codes the fol lowing standards and codes must be followed The Installation must conform with local codes or in the absence of local codes with the National Fuel Gas Code ANSI 2223 1 NFPA 54 latest edition or the Natural Gas and Propane Installation Code CAN CGA B149 1 latest edition This appliance when installed must be electrically grounded in accordance with local codes or in the absence of local codes the National Electrical Code ANSI NFPA 70 latest edition or the Canadian Electrical Code Part 1 CSA C22 1 latest edition N
5. Figure 30 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 25 26 Pilot Flame Appearance Figure 31 Air Shutter Adjustment CAUTION Air shutter is hot while the Epic gas stove is operating and should only be adjusted using a heat resistant glove The air shutter control lever is located inside the main control door above the control panel The lever is linked to the primary air shutter on the main burner The air shutter regulates the amount of primary air the burner receives and therefore how clean the stove burns The air shutter should only be adjusted by a qualified gas technician The stove should burn for about 15 minutes with the logs installed before adjusting the air shutter Moving the lever to the left closing the shutter will raise the height of the flames as well as turn them more yellow orange Moving the lever to the right will open the shutter turning the flames to a cleaner transparent blue and enhance the glow of the logs CAUTION The air shutter should never be set so as to make the tips of the flames sooty or create sooting on the viewing glass logs or firebox ceiling If soot begins to form after burning the air shutter should be opened gradually until the sooting condi tion stops Gas quality and gas pressure may vary which can affect the burning characteristics of the stove Loosen screws to adjust tighten screws when adjustment is complete Air Shutter Adjustment Ha
6. Excessive Combustion Air If the symptoms listed below are present you may need to adjust the flue restrictor to a more closed position Low Flame Pilot pulls and appliance shuts down Pilot flame ghosts LET U yi ES PEA Figure 24 Other approved chimney brand is Simpson Dura Vent DV GS NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Horizontal Terminations The shaded areas in the diagram below show all allowable combinations of vent configurations with horizontal terminations Horizontal sections of pipe require 1 4 of rise for every 12 of run second 90 or 45 elbow in addition to the first 90 elbow at the top of the vertical length of pipe is allowed as long as the overall length of the horizontal run of pipe does not exceed those shown below Use the restrictor positions indicated Note that if the termination cap falls in the unshaded area then no restrictor is installed in the stove RESTRICTOR POSITIONS VE ES hs n ATH ay q LES io is n f 7 Lu Lu LL e 2 cc gt 8 HORIZONTAL MIN 24 VERT PIPE SECT WITH 9 HORIZONTAL SECT _ PARA 2 4 6 8 HORIZONTAL DISTANCE FEET Figure 25 Vertical Terminations The diagra
7. LECTRIQUE D BRANCHEZ L APPAREIL AVANT D EN FAIRE L ENTRETIEN SI L APPAREIL REQUIERT UN BRANCHEMENT LETRIQUE LES RACCORDEMENTS ET LA MISE LA TERRE DOIVENT TRE CONFORMES AUX EXIGENCES DES CODES REGIONAUX ET DU CODE D INSTALLATION ANSI NFPA 70 OU CSA C22 1 Mod le EPIC 33 Mod le EPIC 40 GAZ NATUREL GAZPROPANE GAZNATUREL GAZ PROPANE 33000 23000 31000 24000 4000027000 se000 30000 ORIFICE DMS 0 4500 pi 0 1370 M 1 SP CIFICATIONS a IN WC C L APPAREIL PR USIN EST MUNI D QUIPEMENT POUR 0 2000 PIEDS 0 610 M AU CANADA 0 4500 PIEDS 0 1370M SP CIFICATIONS LECTRIQUE 120 VCA 60 HZ MOINS DE 2 AMP RES CONDUIT CET APPAREIL DOIT ETRE INSTALLER SEULEMENT AVEC UN CONDUIT D EVACUATION RECOMMANDE PAR LE MANUFACTURIER TOUJOURS SE REFERER AU MANUEL D INSTALLATION EN ALTITUDE AU DEL DE 2000 610 M AU CANADA 0 4500 0 1370 LA CAPACIT NERG TIQUE DE L APPAREIL DIMINUE DE QUATRE 4 POUR CHAQUE 1000 PI 305 M CE FOYER RADIANT AU GAZ VACUATION N EST PAS CON U POUR TRE UTILIS AVEC DES FILTRES AIR UTILISER UNIQUEMENT AVEC L CRAN NO J7490 SUIVRE LES INSTRUCTIONS D INSTALLATION D GAGEMENTS AUX COMBUSTIBLES POUCES POSITION EN COIN DIMENSIONS ALCOVE PROFONDEUR MAXIMUM 48 1219mm LARGEUR MAXIMUM 48 1219mm HAUTEUR MAXIMUM 69 1753mm NE REFEREZ VOUS AU MANUEL D INSTALLATION POUR TOUT AUTRE DEGAGEMENT
8. 26 Paint Curing erenneren 26 Optional Wall 26 Operating 0 110 27 Millivolt Control System 27 Maintenance and Servicing 28 31 Maintenance 0 668 51 28 Millivolt and Systems Checks 28 Vent Pipe 28 Glass Door Cleaning and Maintenance 29 Opening and Removing Door 29 Replacing A Damaged Barrier 30 Fuel Conversion 31 Troubleshooting 32 Wire Harness Diagram 33 Replacement Parts 34 36 hrnrcnIp pee m 37 38 Stove Labels 39 40 Warranty nm 41 Product Reference Information 42 USING THIS MANUAL Please read and carefully follow all of the instructions found in this manual Please pay special attention to the safety instructions provided in this manual PRODUCT IS SUBJECT TO CHANGE WITHOUT NOTICE IMPORTANT SAFETY INFORMATION Important S
9. 953 or IHP SV4FC are required 4 1 clearance from the vent pipe to combustible materials must be maintained 5 A maximum of either four 45 elbows or two 90 elbows may be used See Page 21 for allowable offsets 6 The maximum system height is 30 feet 9 1 M and the minimum is 10 feet 3M Storm m Vertical Termination Cap ye Flashing Roof Maintain 1 Clearance to Combustibles Ceiling Minimum Framing 10 x 10 Ceiling Firestop Pipe Length Figure 23 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 19 Flue Restrictors The flue restrictor settings shown in Figures 25 and 26 are for typical installations and may need to be adjusted from standard to take into account other variables in the installationto achieve proper combustion See Flue Restrictor Guidelines on this page to assist you in making a proper flue restrictor adjustment This stove requires a balanced flue to ensure proper combustion As such flue restrictors may need to be installed depending on the vent configura tion of your stove The drawings on the next page show all the allowable pipe configurations for the Epic gas stove To properly install the flue restrictors find your pipe configuration in the drawings on the next page and note which restrictor setting is recommended The flue restrictors are shipped in the firebox of your stove Install the flue restrictors using the four allen head screws acc
10. curit et votre Seguridad y su po les au gaz chimenea iTodas las partes de la chimenea IHP se ponen deviennent EXTR MEMENT EXTREMELY HOT To prevent severe burns and injuries do Not remove the barrier on the stove front which prevents direct contact with the glass Follow the safety instructions below and be sure everyone in your household understands this burn hazard The surfaces on your fireplace get EXTREMELY HOT The glass on the front of the fireplace reaches EXTREMELY HIGH temperatures and can cause severe burns if touched Keep children away from an operating fireplace Closely supervise children in any room where a fireplace is operating to prevent contact with glass Keep clothing furniture gasoline and other flammable liquids away from the fireplace Even after the gas is turned off fireplace surfaces remain extremely hot Be sure to attach the enclosed Safety in Operation Warnings where you turn on your fireplace to help remind everyone of the dangers associated with high temperatures see pages 6 7 Read Important Safety Information on page 5 ENGLISH CHAUDES Afin d viter les br lures graves ou les blessures ne pas retirer l cran ou la protection qui emp che tout contact direct avec la vitre Suivez les instructions de s curit ci dessous et veillez ce
11. defective Thermopile may not be generating sufficient millivolts See Firebox Liner Kit Log Set and Ember Installation Check for obstructions in vent pipe check for proper restrictor setting See Flue Restric tors See Air Shutter Adjustment See Quiet Operation The noise may be reduced by slightly turning the flame down Turning the flame down will reduce the heat output of the fireplace Clean orifice Have your gas supplier check for correct gas pressure 7 W C natural gas 11 W C LP gas See Firebox Liner Kit Log Set and Ember Installation Turn on gas To purge hold in control knob in pilot position for 1 2 minutes and light Check for spark at electrode and pilot if no spark and electrode wire is properly connected replace igniter See Lighting Instructions Check pilot flame adjustment see Maintenance and Servicing section Check the connection between the thermocouple lead and the valve Turn control knob to pilot and push in and light pilot While lit take millivolt reading at lead going into valve s CPU Minimum reading should be 17 millivolts If less replace thermocouple Purge air in pilot gas line by holding in control knob at pilot and sparking igniter The air in the line may take up to several minutes to purge See Lighting Instructions Disconnect rocker switch and thermostat wires at terminals 1 and 3 on valve Jumper across from 1 to 3 with pilot lit If burner comes on eithe
12. plied from the manufacturer Normally all parts should be ordered through your IHP distributor or dealer Parts will be shipped at prevailing prices at time of order Model Number When ordering repair parts always give the following information 1 The model number of the appliance 2 The serial number of the appliance 3 The part number 4 The description of the part 5 The quantity required 6 The installation date of the appliance If you encounter any problems or have any questions concerning the installation or application of this system please contact your dealer Innovative Hearth Products 1508 Elm Hill Pike Suite 108 Nashville TN 37210 visit us at IronStrike us com Serial Number Date Installed Your Dealer s Name Fuel Type Checkone Natural Gas NATIONAL FIREPLACE INSTITUTE NFI We recommend that our gas hearth products be installed and serviced by profes sionals who are certified in the U S by the National Fireplace Institute NFI as NFI Gas Specialists CERTIFIED www nficertified org Propane Gas LP NATIONAL FIREPLACE INSTITUTE NFI Nous recommandons que nos foyers au gaz soient install s et que l entretien soit effectu par des profes sionnels certifi s par le National Fireplace Institute CERTIFIED NFI Etats Unis seulement www nficertified org IHP reserves the right to make changes at any time without notice in desi
13. 000 39 000 30 000 MANIFOLD PRESSURE IN WC 35117 10 0 54 35117 10 0 54 UNIT FACTORY EQUIPPED FOR 0 2000 FT 0 610 M IN CANADA 0 4500 FT 0 1370 M ELECTRICAL RATING 120 VAC 60 HZ LESS THAN 2 AMPS VENTING THIS APPLIANCE MUST BE PROPERLY CONNECTED TO A VENTING SYSTEM IN ACCORDANCE WITH THE MANUFACTURER S INSTRUCTIONS SEE MANUFACTURER S INSTALLATION INSTRUCTIONS FOR APPROVED PIPE BRANDS AND PIPE SEALING PROCEDURES FOR ALTITUDES ABOVE 2 000 FT 610M IN CANADA 4500 FT 1370M DE RATE THE APPLIANCE BY FOUR 4 FOR EVERY 1 000 FT 305 M THIS VENTED GAS FIREPLACE HEATER IS NOT FOR USE WITH AIR FILTERS FOR USE ONLY WITH BARRIER PART NO J7490 FOLLOW INSTALLATION INSTRUCTIONS MINIMUM CLEARANCES TO COMBUSTIBLES IN INCHES ALCOVE DIMENSIONS MAXIMUM DEPTH 48 1219mm MINIMUM WIDTH 48 1219mm ons MINIMUM HEIGHT 69 1753mm 1 SEE OWNER S MANUAL FOR OTHER ALCOVE CLEARANCE CONFIGURATIONS ALCOVE OR PARALLEL INSTALLATION HEARTH PROTECTION SEE INSTRUCTION MANUAL CORNER INSTALLATION CAU TION HOT WHILE IN OPERATION DO NOT TOUCH SEVERE BURNS MAY RESULT KEEP CHILDREN CLOTHING FURNITURE GASOLINE AND OTHER LIQUIDS HAVING FLAMMABLE VAPORS AWAY KEEP BURNER AND CONTROL COMPARTMENT CLEAN SEE INSTALLATION AND OPERATING INSTRUCTIONS ACCOMPANYING APPLIANCE FOR USE WITH GLASS DOORS CERTIFIED WITH THIS APPLIANCE ONLY DO NOT OPERATE THE APPLIANCE WITH GLASS REMOVED CRACKED OR BROKEN REPLACEMENT OF THE PANEL S SHOULD BE DO
14. CONTROL DR LATCH BRACKET 10 SHEETMETAL HEATSINK 21 REAR TOP HINGE 32 CONTROL DOOR LATCH 11 HEATSINK GASKET 22 SMALL RELIEF DOOR GASKET 35 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE REPLACEMENT PARTS DIAGRAMS EPIC 33 40 EPIC33 40 NO 33 34 35 37 38 39 40 41 42 43 36 DESCRIPTION FLAME CONTROL EXTENSION PILOT CONTROL EXTENSION VALVE ASSY BLACK IRON PIPE STREET ELBOW BRACKET VALVE CONTROL PANEL DASHBOARD ON OFF SWITCH RHEOSTAT PIEZO IGNITER NO 44 45 46 47 48 49 50 51 52 53 54 DESCRIPTION NO BLOWER 95 SLIDER WASHER 56 CASSETTE PLATE 97 BULKHEAD SPACER FITTING BULKHEAD ORIFICE PILOT ASSEMBLY BRACKET PILOT ASSEMBLY CASSETTE GASKET FAN GRILL COVER FAN GRILL MOUNT NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 5 amp 5 5 DESCRIPTION AC POWER PLUG PEDESTAL BACK THERMO OUTLET BRACKET Gas Conversion Kits Product Reference Information F2325 EPIC33 40 DVS C ACCESSORIES a m 6 75355 EPIC CK LP to NG Conversion Kit LP to NG ref form 775235 75352 EPIC CK NG to LP Conversion Kit NG to LP ref form 775244m Trim Kits for Door Frame Upper and Lower ref form 775291M converts from standard 40 000 BTU input to optional 33 000 BTU input Kits Include Matching Trim Orifice Main Burner 36 NG 33 000 BTU 5 Cat N
15. NE COUVREZ PAS CETTE TIQUETTE Fabriqu aux U S A NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 39 LIGHTING LABEL WARNING IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE PERSONAL INJURY OR LOSS OF LIFE CAUTION HOT WHILE IN OPERATION DO NOT TOUCH KEEP CHILDREN FURNITURE GASOLINE AND OTHER LIQUIDS WITH FLAMMABLE VAPORS AWAY NEVER OPERATE UNIT WITH GLASS DOOR OFF OR ATTEMPT TO OPEN 40 THE DOOR WHILE HOT A This appliance is equipped with a piezo ignition device to light the pilot When lighting the pilot follow these instructions exactly B BEFORE LIGHTING smell around the appliance area for gas Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor WHAT TO DO IF YOU SMELL GAS DONOT try to light the appliance DONOT touch any electric switch do not use any phone in the building CAUTION YOUR IHP GAS APPLIANCE MUST ALWAYS BE OPERATED WITH GLASS DOOR IN PLACE 1 STOP Read the safety information above on this label GAS CONTROL ON OFF FLAME HEIGHT 2 Open the lower door Make sure gas supply shut off cocks are open and ON OFF Rocker Switch is OFF If equipped with a thermostat af os set it to the lowest setting 9 3 Tum off all electrical power to the appliance 4 Push Gas Control Knob slightly and turn clockwise to OFF NOTE Kno
16. el artefacto debe situarse fuera de las reas de tr fico y lejos del mobiliario y cortinas 4 Se debe alertar a los ni os y adultos sobre los peligros de las altas temperaturas en la superficie y que se mantengan alejados para evitar quemaduras o ignici n de la ropa 5 No debe colocarse ropa u otros materiales inflamables sobre y cerca del artefacto 6 Se debe supervisar de cerca a los ni os cuando est n en el mismo cuarto que el artefacto Los ni os peque os los j venes y otras personas pueden ser susceptibles a quemaduras por contacto accidental Se recomienda instalar una barrera f sica si hay personas en riesgo en la casa Para restringir el acceso a una chimenea o estufa instale una puerta de seguridad ajustable para mantener a los ni os peque os j venes y otras personas en riesgo fuera del cuarto y lejos de las superficies calientes 7 Cualquier malla o resguardo de seguridad quitado para dar servicio a un artefacto debe reinstalarse antes de operar el artefacto 8 Una persona de servicio competente debe realizar la instalaci n y reparaci n Una persona de servicio profesional debe inspeccionar el artefacto antes de usar al menos una vez por a o Se puede requerir limpieza m s frecuente debido a la pelusa excesiva del alfombrado del material de cobijas etc Es imprescindible mantener limpios los compartimientos de control los quemadores y los pasajes de circulaci n del aire del artefacto Ver las
17. et le maintenir dans cette position Appuyez imm diatement sur le bouton allumeur Pi zo lectrique situ gauche du robinet de contr le du gaz L tincelle produite par Pallumeur Pi zo lectrique doit allumer la veilleuse Continuez maintenir le bouton de contr le dans cette position pendant environ 30 secondes apr s l allumage de la veilleuse Rel chez le bouton de contr le du gaz qui reviendra la position initiale La veilleuse doit rester allum e R p tez les tapes 4 8 pendant 15 secondes suppl mentaires si la veilleuse s teind Th il Sila manette ne se soul ve pas d elle m me lorsqu on la rel che arr ter et rmopl e Allumeur Veilleuse gaz appeler imm diatement un technicien qualifi ou le fournisseur de gaz Thermocouple Sila veileuse ne reste pas allum e apr s plusieurs essais tournez le Y bouton de contr le du gaz la position OFF et appelez imm diatement un technicien qualifi ou votre distributeur de gaz 9 Lorsque la veilleuse est allum e tournez le bouton de contr le du gaz dans le sens invers des aiguilles d une montre pour le placer la position PILOT ASSEMBLY ON Le bouton de contr le peut tre tourn la position ON seulement si il n est plus enfonc 10 Pour allumer le br leur mettre l interrupteur la position ON ou ajustez le thermostat la temp rature souhait e 11 Ajustez la flamme et la temp rature souhait e en tournan
18. fragile so handle them with care Figure 16 2 Install left rear log B onto the front half of log stand 1 see Burner Pan Diagram Page 14 When installed correctly it should sit firmly in place with the charred surface facing the center of the firebox 3 Place the rear log A onto log stands 1 and 2 see Burner Pan Dia gram Page 14 The charred surface of the log should face the front 4 Place the embers volcanic stone E on the burner pan Using the larger embers first create a small pile on the elevated air deflector near the center and place them along the front edge of the burner leaving about 1 4 in between each ember and a 2 gap in the center It will not affect the performance but smaller embers may fall into the front air gap Place the rest of the embers throughout the firebox taking care not to block off any secondary air holes or gas ports see example below for proper placement of embers Figure 18 5 Place the glowing embers rockwool F over the gas ports and in between the ember volanic stone along the front of the firebox The glowing embers can be placed over gas ports but do not cover the secondary air holes see Burner Pan Diagram Page 14 Figure 19 6 Place the left front log C on log stand 3 see Burner Pan Diagram Page 14 and the center log D spanning from log stand 4 to the peg found on the right side of rear log A When installed correctly both logs should sit fir
19. herein to obtain a listing of approved dealers distributors IHP shall in no event be responsible for any warranty work done by a contractor that is not approved without first obtaining IHP s prior written consent HOW TO REGISTER A CLAIM AGAINST WARRANTY In order for any claim under this warranty to be valid you must contact the IHP dealer distributor from which you purchased the product If you cannot locate the dealer distributor then you must notify IHP in writing IHP must be notified of the claimed defect in writing within 90 days of the date of failure Notices should be directed to the IHP Warranty Department at 1508 Elm Hill Pike Suite 108 Nashville TN 37210 or visit our website at WWW IRONSTRIKE US COM Printed in U S A 2013 Innovative Hearth Products LLC Innovative Hearth Products P N 900197 00 Rev NC 12 2013 i VN A LAS VFX A LAS AE Y L gt Z SN PSS RIRE TR TEE RIRE ES RTS AIK ER SSL IES O SS O SS SR RERS SS ISS LINES SS NY M RSA EEE RS EEE REV EEE RS AN VE EE RSA EE RSA 1 lt gt ARCS RK 1508 Elm Hill Pike Suite 108 Nashville TN 37210 42 PRODUCT REFERENCE INFORMATION We recommend that you record the following important information about your appliance Please contact your IHP dealer for any questions or concerns REPLACEMENT PARTS See Page 34 for a complete replacement parts list Use only parts sup
20. instrucciones de mantenimiento en la p ginas 28 30 HOMEOWNER S INSTRUCTIONS ATTACHING SAFETY IN OPERATION WARNINGS ATTACHING SAFETY IN OPERATION WARNINGS Yourfireplace has been furnished with safety instruc tion labels that are to be affixed to the operation and control point of the fireplace A safety instruction label should beaffixed to the wall switch plate where the fireplace is turned on and off See Figure A or wall thermostat See Figure B and if used on the remote control handheld transmitter Figure C The warnings should already have been put in place when the fireplace initial set up was completed If they are not affixed at these spots locate the multi lingual adhesive labels provided with these instructions and proceed as follows 1 Locate the wall switch or wall thermostat that controls the fireplace verify the switch operates the fireplace by turning it on and off Clean the wall switch plate or wall thermostat thoroughly to remove any dust and oils Affix the label to the surface of the plate of the wall switch that controls the fireplace Figure A or the wall thermostat Figure B Choose the language primarily spoken in the home 2 faremotecontrolis used to control the fireplace locate the transmitter and clean it thoroughly to remove any dust and oils Affix the label to the surface of handheld transmitter Figure C Choose the language primarily spoken in the home 3 If you are unable to loc
21. more affected by carbon monoxide than others including pregnant women people with heart or lung disease or anemia those under the influence of alcohol and those at high altitudes Turn off gas and electrical power to the appliance and allow it to cool before cleaning or servicing the appliance If the barrier becomes damaged the barrier shall be replaced with the manufacturer s barrier for this appliance Si l cran est endommag il doit tre remplac par celui fournit par le fabricant de cet appareil Reinstall any barrier removed before operating the appliance The barrier is designed to reduce the risk of burns from hot glass Do not operate the appliance without the barrier installed Appliance Operation Notices These gas stoves are vented gas appliances Do not burn wood or other material in these appliances These appliances are designed to operate on natural gas or propane gas only The use of other fuels or combinations of fuels will degrade the performance of this system and may be dangerous Provide adequate clearances around air openings and adequate accessibility clearance for service and proper op eration Never obstruct the front openings of the appliance These appliances are designed as supplemental heaters Therefore it is advisable to have an alternate primary heat source when installed in a dwelling Warranty Information Your gas appliance is covered by a limited 20 year warranty Youwillfinda c
22. physique si des personnes risques habitent la maison Pour emp cher l acc s un foyer ou un po le installez une barri re de s curit cette mesure emp chera les tout petits les jeunes enfants et toute autre personne risque d avoir acc s la pi ce et aux surfaces chaudes 7 Tout cran ou protecteur retir pour per mettre l entretien de l appareil doit tre remis en place avant de mettre l appareil en marche 8 L installation et la r paration devrait tre confi es un technicien qualifi L appareil devrait faire l objet d une inspection par un technicien professionnel avant d tre utilis et au moins une fois l an par la suite Des nettoyages plus fr quents peuvent tre n cessaires si les tapis la literie et cetera produisent une quantit importante de pous si re Il est essentiel que les compartiments ahritant les commandes les br leurs et les conduits de circulation d air de l appareil soient tenus propres Voyez les instructions d entretien la pages 28 30 Informaci n importante de seguridad 1 ADVERTENCIA No opere el artefacto con el frente de vidrio quitado agrietado o roto 2 Nouse este artefacto si alguna de sus partes ha estado bajo agua Llame de inmediato a un t cnico de servicio calificado para que inspeccione el artefacto y reemplace cualquier parte del sistema de control y cualquier control de gas que haya estado bajo agua 3 Debido a las altas temperaturas
23. slide straight onto male ends of adjacent pipes and fittings by orienting the four pipe indentations so they match and slide into the four entry slots Push pipe sections completely together then twist lock one section clockwise approximately one quarter turn until the two sections are fully locked The female locking lugs will not be visible from the outside on the pipe or fittings They may be located by examining the inside of the female ends Supports Horizontal runs of vent must be supported every 3 feet Wall straps are available for this purpose Pipe Sealing If Simpson Dura Vent pipe is used the pipe must be sealed as follows seal both the inner and outer pipes with a high temperature silicone sealant rated for at least 600 F commonly know as RTV Run a 1 8 3mm bead of silicone around outside of male end of outer sleeve Run a 1 8 3mm bead of silicone about 1 4 6mm from the end of the male inner pipe which is found in the pipe to be attached above Twist lock the pipes or fittings together Female Locking Lugs Sealant Male Locking Lugs Figure 22 Other approved chimney brand is Simpson Dura Vent DV GS NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 17 18 Vent Parts List Secure Vent direct vent pipe may be used with the Epic gas stove Please see the lists below to verify the components available from each direct vent pipe manufacturer Snorkel terminations are available for app
24. the stove for example a rocker switch and a wall thermostat Additional switches may affect the system resistance and increase the chance of the burner not igniting Follow the instructions included with the thermostat or remote control for wiring The thermostat remote control and rocker switch will turn the burner on and off independently Be sure to set the rocker switch to the Off position when using the thermostat or remote control and set the thermostat or remote control to the lowest temperature when you wish to use the rocker switch only otherwise one may override the other Millivolt Control Schematic Sparker Piezo Igniter Thermocouple Pressure Taps Gas Inlet Figure 33 Pilot Hood Thermostat Wire Maximum Length 100 Feet Millivolt Control System This stove operates on a millivolt control system As such no additional power supply is needed for the stove to heat The pilot assembly contains athermocouple that when heated by the pilot flame generates electricity millivolts mV 1 1000 of a volt which opens a valve allowing gas to continue flowing to the pilot assembly The pilot assembly also contains a thermopile that when heated by the pilot flame generates electricity that flows to terminal 1 labeled TPTH on the gas valve When the electricity is conducted from terminal 1 through the on off switch thermostat or receiver of the remote control to terminal 3 labeled TH on the gas va
25. 981 Snorkel Termination 36 982 Snorkel Termination 14 984 Horizontal Termination Cap 985 Horizontal Termination Cap High Wind 980 Vertical Termination Cap 991 Vertical Termination Cap High Wind Horizontal Vent Installation Venting terminals may not be recessed into a wall or siding co A o co co Set the unit in the desired location Check whether or not wall studs are in the way when the venting system is attached If wall studs are in the way you may want to adjust the location of the unit All horizontally terminated vent installations may only use 6 5 8 x 4 Secure Vent pipe Assemble the desired combination of pipe and elbow s to the appli ance Adaptor with pipe seams facing down Offsetting the pipe seams as double seams in one place will cause the outer pipe to take an oval shape When this pipe passes through a wall a wall thimble Simpson 942 or IHP SV4RSM is required The hole in the wall for the wall thimble should be 9 1 4 x 10 1 4 If the wall being penetrated is constructed of non combustible material i e masonry block or concrete a 7 diameter hole is acceptable and a wall thimble is not required Horizontal runs of vent pipe must be supported every 3 feet Wall straps IHP SV4BM or Simpson 988 are available for this purpose If the vent passes through a ceiling or floor a firestop IHP SV4BF or Simpson 963
26. ATION ll est imp ratif que les tiquettes de s curit fournies avec le foyer soient coll es c t des dispositifs de contr le du foyer Une tiquette de s curit doit tre coll e sur la plaque de l interrupteur contr lant l allumage du foyer voir Figure A ou sur lethermostat mural voir Figure B et le cas ch ant sur le bo tier de la t l commande Figure C Pour achever l instal lation correcte de ce foyer proc dez comme suit avec les tiquettes adh sives en langues trang res fournies avec les instructions d utilisation et d entretien 1 Rep rez l interrupteur ou le thermostat mural qui contr le le foyer v rifiez que l interrupteur contr le le fonctionnement du foyer en le faisant basculer de Marche Arr t et vice versa Nettoyez soigneusement la plaque murale de l interrupteur ou le thermostat mural pour liminer la poussi re et les traces de graisse ou d huile Collez l tiquette sur la surface de la plaque de l interrupteur mural qui contr le le foyer Figure A ou du thermostat mural Figure B Choisissez la langue qui est principalement parl e dans la r sidence du propri taire En cas de doute collez l tiquette en anglais 2 Si une t l commande est utilis e pour contr ler le foyer nettoyez la soigneusement pour liminer la poussi re et les traces de graisse ou d huile Collez l tiquette sur le boitier de la t l commande Figure C Choisissez la langue qui est principa
27. BE CAREFUL NOT TO SPRAY COMMERCIAL GLASS CLEANER WITH AMMONIA ON GASKET AREA OF DOOR AM MONIA WILL DISSOLVE GASKET GLUE NOTE GOLD PLATED SURFACE MUST BE CLEANED WITH GLASS CLEANER AND SOFT RAG BEFORE FIRING THE FIRST TIME OR FINGER PRINTS AND STAINS WILL REMAIN PERMA NENTLY NEVER USE BRASS POLISH TO CLEAN GOLD THIS WILL REMOVE GOLD PLATING Figure 35 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 29 30 Replacing the Damaged Barrier Barrier e Ifthe barrier becomes damaged the barrier shall be replaced with the manufacturer s barrier for this appliance e For use with barrier Part No J7490 Follow installation instructions To remove the damaged barrier Shut off the main burner using the rocker switch Shut off the pilot flame by turning the pilot knob clockwise to the off position Pull open the left side door Unlatch the main door and open 5 Locate the six nuts on the back side of the main door and remove them using an 5 16 socket 6 Remove the barrier with trim gt 6 Installing is the reverse of removal Figure 36 1 Replace barrier with Part No J7490 2 Reinstall trim into the new barrier 3 Reinstall nuts 4 Latch the main door then close the side door Fuel Conversion Converting the stove between natural gas NG and propane LP can be accomplished by either changing the cassette valve and pilot assembly or
28. ESE INSTRUCTIONS EXACTLY A FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE INJURY OR LOSS OF LIFE A This appliance is equipped with a piezo ignition devicetolightthe pilot When lighting the pilot follow these instructions exactly B BEFORE LIGHTING smell around the appliance area for gas Be sure to smell next to the floor because some gas is heavier than air and will settle on the floor WHAT TO DO IF YOU SMELL GAS e DO NOT try to light the appliance DO NOT touch any electric switch do not use any phone in your building e Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e f you cannot reach your gas supplier call the fire department C Use only your hand to push in or turn the gas control knob Never use tools If the knob will not push in or turn by hand don t try to repair it call a qualified service technician Force or attempted repair may result in a fire or explosion DO NOT use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water LIGHTING INSTRUCTIONS 1 STOP Read the safety information on this page before proceeding If applicable Set the thermostat to lowest setting Turn wall on off switch unit mounted on off switch or remote control switch OFF 3 T
29. EW YORK CITY NEW YORK MEA Installation of these appliances are approved for installation in New York City in the US state of New York MEA 138 07 E COMMONWEALTH OF MASSACHUSETTS REQUIREMENTS These appliances are approved for installation in the US state of Mas sachusetts if the following additional requirements are met nstall this appliance in accordance with Massachusetts Rules and Regulations 248 C M R Sections 4 00 through 8 00 Installation and repair must be done by a plumber or gas fitter licensed in the Commonwealth of Massachusetts The flexible gas line connector used shall not exceed 36 inches 92 centimeters in length The individual manual shut off must be a T handle type valve Massachusetts Horizontal Vent Requirements Inthe Commonwealth of Massachusetts horizontal terminations installed less than seven 7 feet above the finished grade must comply with the following additional requirements e hard wired carbon monoxide detector with an alarm and battery back up must be installed on the floor level where the gas fireplace is installed The carbon monoxide detector must comply with NFPA 720 be ANSI UL 2034 listed and be ISA certified A metal or plastic identification plate must be permanently mounted to the exterior of the building ata minimum height of eight 8 feet above grade and be directly in line with the horizontal termination The sign must read in print size no less than one half 1 2 in
30. G Improper installation adjustment alteration service or maintenance can cause injury or property damage For assistance or additional information consult a qualified installer service agency or your gas supplier Operation of this appliance when not connected to a properly installed and maintained venting system can result in carbon monoxide CO poisoning and possible death SHUTDOWN PROCEDURE 1 To turn off the burner switch the rocker switch to OFF or adjust the thermostat to a setting below room temperature if installed The pilot will remain lit for future burner ignition Part No 36252 Rev E 12 2014 8 POUR PLUS DE S CURIT LIRE AVANT D ALLUMER AVERTISSEMENT si VOUS NE RESPECTEZ PAS RIGOUREUSEMENT LES INSTRUCTIONS CI DESSOUS VOUS POURRIEZ ENCOURIR UN RISQUE D INCENDIE ET OU D EXPLOSION QUI POURRAIENT CAUSER DES DOMMANGES MAT RIELS ET CORPORELS POUVANT ENTRA NER LA MORT DANGER CET APPAREIL D GAGE DES TEMP RATURES LEV ES ET DEVRAIT TRE INSTALL For complete shutdown See TO TURN OFF GAS TO APPLIANCE above CART DES ENDROITS TRES PASSANTS ET LOIN DES MEUBLES ET RIDEAUX GARDEZ LA ZONE AUTOUR DU FOYER EXEMPTE DE MAT RIAUX COMBUSTIBLES D ESSENCE ET AUTRES VAPEURS ET LIQUIDES INFLAMMABLES A Cet appareil utilise un syst me d allumage par tincelle allumeur Pi zo lectrique pour allumer la veilleuse Assurez vous de suivre rigoureusement les instructions d allumage de la
31. IRONSTRIKE HEAT FOR LIFE P N 900110 00 REV B 01 2015 A French manual is available upon request Order P N 900182 00 Ce manuel d installation est disponible en francais s implement en faire la demande Num ro de la pi ce 900182 00 INSTALLATION AND OPERATION P900110 00 Direct Vent Epic PES Ds MODEL EPIC33 40 The Epic Gas Stove is factory equipped for 40 000 BTU input and can be con verted to 33 000 using a smaller orifice provided in optional orifice kit P N H5924 This appliance may be installed in an aftermarket permanently located manufactured home USA only or mobile home where not prohibited by local codes This appliance is only for use with the type of gas indicated on the rating plate This appliance is not convertible for use with other gases unless a certified kit is used Cet appareil peut install dans une maison pr fabriqu e mobile d j install e demeure si les r glements locaux le permettent Ce appareil doit tre utilis uniquement avec le type de gaz indiqu sure la plaque signal tique Cet appareil ne peut tre converti d autres gaz sauf si une trousse de conversion est utils e WARNING FIRE OR EXPLOSION HAZARD Failure to follow safety warnings exactly could result in serious injury death or property damage Do store or use gasoline or other flammable vapors and liquids in the vicinity of this or any other appliance WHAT TO DO IF
32. NE BY A LICENSED OR QUALIFIED PERSON WARNING IMPROPER INSTALLATION ADJUSTMENT ALTERATION SERVICE OR MAINTENANCE CAN CAUSE INJURY OR PROPERTY DAMAGE REFER TO THE OWNER S INFORMATION MANUAL PROVIDED WITH THIS APPLIANCE FOR ASSISTANCE OR ADDITIONAL INFORMATION CONSULT A QUALIFIED INSTALLER SERVICE AGENCY OR GAS SUPPLIER Part No No Pi ce 900382 00 Rev 0 12 2014 DO NOT REMOVE OR COVER THIS LABEL Made in U S A HOMOLOGUE FOYER RADIANT PREFABRIQUE AU GAZ NE PAS UTILISER AVEC DU COMBUSTIBLE SOLIDE MAY BE INSTALLED IN RESIDENTIAL BEDROOMS AND MANUFACTURED MOBILE HOMES CONFORME AU STANDARD ANSI Z21 88 2014 CSA 2 33 2014 UL307B CSA P 4 1 09 ET CAN CGA 2 17 M91 R2009 CET APPAREIL DOIT TRE INSTALL CONFORM MENT AUX EXIGENCES DES CODES R GIONAUX ET DU CODE D INSTALLATION ANSI NFPA 54 DERNIERE EDITION ETATS UNIS OU CAN CGA B149 1 DERNIERE EDITION CANADA POUR LES MAISON MOBILE LE STANDARD DE S CURIT EST TITLE 24CFR PART 3280 CET APPAREIL DOIT ETRE INSTALLER SELON LES SPECIFICATIONS DU MANUFACTURIER CET APPAREIL DOIT TRE UTILIS AVEC LE TYPE DE GAZ INDIQU SUR LA PLAQUE SIGNAL TIQUE ET PEUT TRE INSTALL DANS UNE MAISON PR USIN E OU DANS UNE MAISON MOBILE FIXE L O LES CODES R GIONAUX LE PERMETTENT VOIR LE MANUEL D ENTRETIEN POUR PLUS DE D TAILS CET APPAREIL NE PEUT PAS TRE CONVERTI POUR L USAGE AVEC D AUTRES TYPES DE GAZ MOINS D UTILISER UNE TROUSSE DE CONVERSION HOMOLOGU E DANGER RISQUE DE CHOC
33. NNEAU DES COMMANDES CONTREDIT CETTE TIQUETTE C EST QUE LE TYPE DE CARBURANT DE CET APPAREIL A T CONVERTI VENTED GAS FIREPLACE HEATER NOT FOR USE WITH SOLID FUEL MAY BE INSTALLED IN RESIDENTIAL BEDROOMS AND MANUFACTURED MOBILE HOMES CONFORMS TO ANSI Z21 88 2014 CSA 2 33 2014 UL307b CSA P 4 1 09 AND CAN CGA 2 17 M91 R2009 THIS APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH LOCAL CODES IF ANY IF NOT FOLLOW THE CURRENT ANSI Z223 1 NFPA 54 LATEST EDITION USA OR CAN CGA B149 1 LATEST EDITION CANADA AND SAFETY STANDARD TITLE 24 CFR PART 3280 FOR MOBILE HOMES ALSO APPLIANCE MUST BE INSTALLED IN ACCORDANCE WITH THE MANUFACTURER S INSTALLATION INSTRUCTIONS THIS APPLIANCE IS ONLY FOR USE WITH THE TYPE OF GAS INDICATED ON THE RATING PLATE AND MAY BE INSTALLED IN AN AFTERMARKET PERMANENTLY LOCATED MANUFACTURED MOBILE HOME WHERE NOT PROHIBITED BY LOCAL CODES SEE OWNER S MANUAL FOR DETAILS THIS APPLIANCE IS NOT CONVERTIBLE FOR USE WITH OTHER GASES UNLESS A CERTIFIED KIT IS USED DANGER RISK OF ELECTRICAL SHOCK DISCONNECT POWER BEFORE SERVICING UNIT IF ELECTRICALLY CONNECTED CONNECTIONS AND GROUNDING MUST BE IN ACCORDANCE WITH LOCAL CODES IF ANY IF NOT FOLLOW THE CURRENT NATIONAL ELECTRICAL CODE ANSI NFPA 70 LATEST EDITION USA OR CSA C22 1 LATEST EDITION CANADA Model EPIC 33 Model EPIC 40 RATINGS NATURAL GAS LP GAS NATURAL GAS LP GAS MAXIMUM INPUT BTUH 0 2 000 FT 0 610 M 33 000 23 000 31 000 24 000 40 000 27
34. OT TO SCALE COLOCACI N DEADVERTENCIAS DE SEGURIDAD EN OPERACION Su chimenea incluye etiquetas de instrucciones de seguridad que deben colocarse enel punto de operaci n ycontroldelachimenea Se debe colocar unaetiqueta instrucciones de seguridad en la placa del interruptor de pared desde el cual se enciende y se apaga la chimenea verlaFiguraA oeneltermostato de pared verla Figura B y en el transmisor de control remoto Figura C si se usa Las advertencias ya deben haberse colocado cuando secomplet la instalaci n inicial de lachimenea Si no est n colocadas en estos lugares encuentre las etiquetas adhesivas multiling es proporcionadas con estas instrucciones y prosiga de la siguiente manera 1 Identifique el interruptor o el termostato de pared quecontrolala chimenea verifique queel interruptor opera la chimenea encendi ndola y apag ndola Limpie bien la placa del interruptoro eltermostato de pared para quitar el polvo y aceite Pegue la etiqueta en lasuperficie de la placa del interruptor que controla la chimenea Figura A o en el termostato de pared Figura B Seleccione el idioma que m s se habla en la casa 2 Si se usa un control remoto para controlar la chimenea encuentre el transmisor y l mpielo bien para quitar el polvo y aceite Pegue la etiqueta en la superficie del transmisor Figura C Seleccione el idioma que m s se habla en la casa 3 Siustedesincapazdelocalizarlas etiquetas porfavor p
35. REQUIS PROTECTIONS AU PLANCHER REFEREZ VOUS AU MANUEL D INSTALLATION 4 02m POSITION PARALL LE OU POSITION DE L ALC VE DANGER CET APPAREIL D GAGE DES TEMP RATURES LEV ES ET DEVRAIT TRE INSTALL L CART DES ENDROITS TR S PASSANTS ET LOIN DES MEUBLES ET RIDEAUX SURVEILLEZ LES ENFANTS QUI SE TROUVENT DANS LA PI CE GARDEZ LA ZONE AUTOUR DU FOYER EXEMPTE DE MAT RIAUX COMBUSTIBLES D ESSENCE ET AUTRES VAPEURS ET LIQUIDES INFLAMMABLES MAINTENEZ LE BR LEUR ET LE BO TIER DES COMMANDES PROPRE EN TOUT TEMPS VOIR LES MANUELS D INSTALLATION ET D ENTRETIEN QUI ACCOMPAGNENT L APPAREIL SEUL LE PANNEAU VITR FOURNI PAR LE MANUFACTURIER PEUT TRE UTILIS AVEC CET APPAREIL EN AUCUN CAS L APPAREIL NE PEUT TRE UTILIS SANS LA VITRE OU AVEC LA VITRE BRIS E LE REMPLACEMENT DE LA VITRE DOIT TRE EFFECTU PAR UN TECHNICIEN DE SERVICE QUALIFI AVERTISSEMENT UNE INSTALLATION INAD QUATE DE M ME QU UN AJUSTEMENT UNE MODIFICATION UNE R PARATION OU UN ENTRETIEN INCORRECTS PEUVENT CAUSER DES BLESSURES OU DOMMAGES LA PROPRI T R F REZ VOUS AU MANUEL D ENTRETIEN LIVR AVEC CET APPAREIL POUR DE L ASSISTANCE CONSULTEZ UN INSTALLATEUR QUALIFI UNE ENTREPRISE DE SERVICE OU UN FOURNISSEUR DE GAZ DATE OF MANUFACTURE DATE DE FABRICATION JAN FEB MAR APR MAY JUN JUL AUG SEP OCT NOV DEC 2014 2015 2016 2017 JANV FEVR MARS AVR MAI JUIN JUIL AO T SEPT OCT NOV DEC 111111111 1 1 1 1 1 1 1 1 1 N ENLEVEZ PAS OU
36. USTRATIONS ARE NOT TO SCALE Gas Line Installation This stove must be connected to the gas line in accordance with local codes and or the National Fuel Gas Code ANSI 2223 1 In Canada the current CAN CGA B149 1 installation code Remove the four screws holding the back of the pedestal in place Slide rear cover back far enough to gain access to the inside of the pedestal Remove plastic plug from the 3 8 x 9 pipe Connect gas line to the 3 8 x 9 pipe After connect ing the gas line all joints in the line and connections at the valve should be checked for leaks before final positioning of the unit Conduct a gas leakage test of the appliance piping and control system downstream of the shutoff valve in the supply line to the appliance Gas Pressure Requirements A MAJOR CAUSE OF OPERATING PROBLEMS WITH GAS APPLIANCES IS IMPROPER GAS PRESSURE The most important item to check during the initial installation and the first thing to check when operating problems occur is gas pressure This appliance will not function properly unless the required gas pressure is supplied See the table on this page for gas pressure requirements Two pressure taps are provided on the appliance s valve to check gas pressures To access the taps remove the four socket head screws from the valve control panel The taps are located below the On Off Pilot knob see Figure 29 on Page 25 The left tap is the inlet supply pressure side To check inlet pressur
37. VER attempt to open door or clean glass when unit is hot O Check the hot air outlet vents for lint or other accumulations Never block or restrict vent openings or obstruct flow of ventilation air O Check that direct vent pipe air intake and flue are open and free of soot blockage or debris The venting system should be periodically examined by a qualified agency O Check gaskets once a year Gaskets must be tight Replace if neces Sary Periodically inspect the pilot system for proper flame NEVER AD JUST THE PILOT until after the gas pressure has been checked and supply lines have been completely bled this may take an hour or more when bleeding through the pilot All pilots are checked and burned at the factory prior to shipment The pilot adjustment screw is located to the lower left of the flame height control knob Adjust the pilot screw to properly size the flames The flames should completely surround the thermopile and thermocouple and extend across the main burner tube ports Be careful not to back the screw out of its threads O Check that the area around the stove is kept clear and is free of combustible materials gasoline and other flammable vapors and liquids O Check the millivolt system as per the table on this page O Periodically inspect the burner flame for proper appearance See Flame Color and Behavior on Page 25 2 Theviewing glass should be cleaned periodically see Glass Door Cleaning and Maintenan
38. YOU SMELL GAS Do not try to light any appliance Do not touch any electrical switch do not use any phone in your building Leave the building immediately Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions e f you cannot reach your gas supplier call the fire department Installation and service must be performed by a quali fied installer service agency or the gas supplier INSTALLATEUR Laissez cette notice avec l appareil CONSOMMATEUR Conservez cette notice pour consul tation ult rieure AVERTISSEMENT RISQUED INDENDIE OU D EXPLOSION Le non respect Des avertissements de s curit pour rait d entrainer des blessures graves la mort ou des dommages mat riels Ne pas entreposer ni utilizer d essence ni d autres vapeurs ou liquides inflammables dans le voisinage de cet appareil ou de tout autre appareil QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ Ne pas tenter d allumer d appareil e Ne touchez aucan interrupteur Ne pas vous servir des t l phones se trouvant dans le b timent o vous trouvez e Sortez imm diatement de b timent e Appelez imm diatement votre fournisseur de gaz depuis un voisin Suivez les instructions du fournis seur e Si vous ne pouvez rejoindre le fournisseur de gaz appelez le service des incindies L installation et l entretien doivent tre assur s par un installateur ou un service d entretie
39. a 0 4500 FT 0 1370 M Canad ENER GUIDE Look for the EnerGuide Gas Fireplace Energy Efficiency Rating in this brochure OThe Steady State Efficiency numbers based on maximum vent configuration Tested to CSA P 4 1 09 Testing Method for Measuring Annual Fireplace Efficiency Electrical Rating 120 VAC 60 HZ Less Than 2 Amps Based on CSA P 4 1 09 11 Preparing Your Epic Stove For Installation Read all instructions before beginning your installation If instructions have not been read carefully your installation could void your warranty and may create a serious fire health or other safety hazard The IHP warranty will be voided if one of the following occurs Installation of any damaged stove or vent system component Unauthorized modification of the direct vent system e Installation other than as instructed by IHP or Simpson Dura Vent Installation of any stove or vent system component not manufac tured or approved by IHP or Simpson Dura Vent When planning the installation for your Epic gas stove it s necessary to consider the following Where the unit is to be installed The vent system configuration to be used Gas supply NG or LP Electrical wiring Optional accessories door trim assembly and wall mounted or remote thermostat Conversion from Standard 40 000 BTU To Optional 33 000 BTU Input To convert input from 40 000 BTUs to 33 000 BTU s remove and replace the stock burne
40. afety Informa tion 1 WARNING Do not operate appliance with the glass front removed cracked or broken 2 Do not use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water 3 Due to high temperatures the appli ance should be located out of traffic and away from furniture and draperies 4 Children and adults should be alerted to the hazards of high surface tem perature and should stay away to avoid burns or clothing ignition 5 Clothing or other flammable material should not be placed on or near the appliance 6 Young children should be carefully supervised when they are in the same room as the appliance Toddlers young children and others may be sus ceptible to accidental contact burns A physical barrier is recommended if there are at risk individuals in the house To restrict access to a fireplace or stove install an adjustable safety gate to keep toddlers young children and other at risk individuals out ofthe room and away from hot surfaces 7 Any safety screen guard or barrier removed for servicing an appliance must be replaced prior to operating the appliance 8 Installation and repair should be done by a qualified service person The appliance should be inspected before use and at least annually by a profes sional service person More f
41. al sources of fire in any home we recommend installing smoke detectors If possible install the smoke detector in a hallway adjacent to the room to reduce the possibility of occasional false activation from the heat produced by the appliance If your local code requires a smoke detector be installed within the same room you must follow the requirements of your local code Check with your local building department for requirements in your area THE EPIC STOVE Must conform with all local state and national installation codes In the absence of local codes the installation must conform with National Fuel Gas Code ANSI Z223 1 latest edition also known as NFPA 54 In Canada the current CAN CGA B149 1 installation code Refer to the National Fuel Gas Code and local zoning and code authorities for details on installation requirements Mobile home installations must conform with the Mobile Home Con struction and Safety Standard Title 24 CFR Part 3280 in Canada CAN CSA Z240 MH or when such a standard is not applicable the Standard for Mobile Home Installations ANSI A225 1 latest edi tion Must be vented directly to the outside in accordance with the latest edition of the National Fuel Gas Code and must never be attached to a chimney serving a separate solid fuel burning appliance Has been certified for use with either natural gas or propane Is not for use with solid fuels Is approved for sitting rooms and or bedrooms
42. alcanza temperaturas EXTREMADAMENTE ALTAS y puede causar quemaduras graves si se toca Mantenga a los ni os alejados de la chimenea en funcionamiento Supervise en forma cercana a los ni os en cualquier cuarto donde haya una chimenea funcionando para impedir el contacto con el vidrio Mantenga la ropa mobiliario gasolina y otros l quidos inflamables alejados de la chimenea A n despu s de haber apagado el gas las superficies de la chimenea permanecen extremadamente calientes Aseg rese de colocar las Etiquetas de advertencia de seguridad de operaci n en el lugar donde enciende la chimenea para que todos recuerden los peligros asociados con las altas temperaturas ver la p ginas 6 7 Lea la Informaci n importante de seguridad en la p gina 5 SPANISH CONGRATULATIONS When you purchased your new gas stove you joined the ranks of thousands of individuals whose answer to their home heat ing needs reflects their concern for aesthetics efficiency and our environment We extend our continued support to help you achieve the maximum benefit and enjoyment available from your new gas stove Thank you for selecting an Innovative Hearth Products LLC IHP gas stove as the answer to your home heating needs TABLE OF CONTENTS Safety and Your Gas Stove 2 3 Using this Manual 4 Important Safety Information
43. ate the labels please contact IHP or your nearest IHP dealer to receive additional safety instruction labels free of charge Cat No H8024 Replacement Label Kit IHP IronStrike us com Note English is red text on clear label French and Spanish are white text on black label SAFETY LABEL DIAGRAMS WARNING EXTREMELY HOT glass and fireplace Risk of Severe Burns ALWAYS KEEP CHILDREN AWAY FROM FIREPLACE Illustrations are for example only Your accessories may be different Les illustrations sont par exemple uniquement Vos accessoires peuvent tre diff rents Las ilustraciones son s lo ejemplos Tu accesorios pueden ser diferentes APPOSITION DES MISES EN GARDE RELATIVES ALA SECURITE D UTILISATION Votre foyer a t livr avec des tiquettes de s curit qui doivent tre coll es c t des dispositifs de contr le du foyer Une tiquette de s curit doit tre coll e sur la plaque de l interrupteur contr lant l allumage du foyer voir Figure A ou sur le thermostat mural voir Figure B et le cas ch ant sur le bo tier de la t l commande Figure C Les mises en garde auraient d tre coll es au moment de l installation initiale du foyer Si ce n est pas le cas prenez les tiquettes adh sives multilingues fournies avec ces instructions et proc dez comme suit 1 Rep rez l interrupteur ou le thermostat mural qui contr le le foyer v rifiez que l interrupteur co
44. b cannot be turned from PILOT to OFF unless Knob is pushed in slightly Do not force 5 Wait five 5 minutes to clear out any gas Then smell for gas including near the floor If you smell gas STOP Follow B in the safety information above If you do not smell gas go to the next step 6 Locate the pilot by looking at the center bottom of the back log Blue flame will be seen when the pilot is lit 7 Turn the gas control knob counterclockwise 43 to the PILOT position 8 Push the knob all the way in and hold in that position Immediately light the pilot by pressing the igniter button 3555 TO TURN OFF GAS TO THE APPLIANCE 1 Turn off the ON OFF rocker switch and or thermostat if installed 2 Turn off all electric power to the appliance if service is to be performed 3 Turn gas control knob clockwise x to OFF Do not force This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air See Installation and Operation Manual accompanying appliance Immediately call your gas supplier from a neighbor s phone Follow the gas supplier s instructions f you cannot reach your gas supplier call the fire department C Use only your hand to push in or turn the gas control knob Never use any tool If the knob will not push in or turn by hand don t try to repair it call a qualified service technician Force or attempted repair may result i
45. cap screw located underneath the door near the front of the stove With both doors open remove the four socket head cap screws two on each side securing the top Lift and remove the top of the stove Unlatch main door and lift straight up off of the locating hinge pins Reinstall door assembly following steps in reverse order A o a Glass Door Cleaning and Maintenance Cleaning Do not remove or clean the glass door when hot When cool the glass may be cleaned with a clean soft cloth and glass cleaner For cleaning white condensation from the interior glass use a gas stove glass cleaner available from your stove dealer Use of caustic or abrasive cleaners may damage glass Gold or nickel plated trim must be cleaned with glass cleaner or denatured alcohol and a soft cloth before firing or fingerprints and stains will remain permanently Never use abrasive polish to clean the gold or nickel as it will ruin the finish DO NOT spray commercial glass cleaner with ammonia on the door and glass gasket as it may dissolve the gasket glue WARNING e DO NOT use abrasive cleaners on glass e DO NOT clean glass when hot Repair If the glass is broken in the glass door the entire door metal frame gasket and glass should be replaced as a unit This replacement glass door is available from your IHP dealer Do not use substitute parts or materials The glass is neo ceramic and alternative types must not be used NOTE
46. ce 3 Shouldrepairs or maintenance ofthe stove require the disassem bly of the vent air intake system the reassembly and resealing should be completed by a qualified service technician and follow the instructions on Page 17 of this manual Meter Reading Should Be Thermostat Connects Connect Millivolt and System Checks Meter Leads to Check To Test Test Terminals Complete 100 MV System or More Thermopile Greater Than Output 325 MV System Resistance See Figure 33 Wiring Terminals Vent Pipe Maintenance Conduct an inspection of the venting system semiannually Recommended areas to inspect are as follows 1 Check areas of the venting system which are exposed to the elements for corrosion These will appear as rust spots streaks or in extreme cases holes These components should immediately be replaced Remove the cap and shine a flashlight down the vent Remove any bird nests or other foreign material Check for evidence of excessive condensate such as water droplets forming in the inner liner and subsequently dripping out at joints Continuous condensate can cause corrosion of caps pipe and fittings It may be caused by having excessive lateral runs too many elbows or exterior portions of the system being exposed to cold weather 4 Inspect joints to verify that no pipe sections or fittings have been disturbed and consequently loosened Also check mechanical supports such as wall straps or plu
47. cette tiquette S il n y a pas d odeur de gaz passez l tape suivante 6 Rep rez la veilleuse situ e au centre de la chambre de combustion sous la b che c ramique arri re Une flamme bleue est visible lorsque la veilleuse est allum e 7 Tournez le bouton de contr le de gaz dans le sens inverse des aiguilles d une montre yx pour le placer sur PILOT 8 Cet appareil de chauffage est equip d un syst me d allumage par tincelle allumeur Pi zo lectirque devant tre utilis pour l allumage de la veilleuse Bouton de contr le LO HI Veilleuse Ouverte De Flamme q pa Allume r Ventilateur Interrupteur Commande De Taille Appelez imm diatement votre fournisseur de gaz depuis un voisin Suivez les instructions du fournisseur Si vous ne pouvez rejoindre le fournisseur appelez le service des incendies C Ne pousser ou tourner la manette d admission du gaz qu la main Ne jamais employer d outil cette fin Si la manette reste coinc e ne tentez pas de la r parer appelez un technicien qualifi Quiconque tente de forcer la manette ou de la r parer peut provoquer une explosion ou un incendie D N utilisez pas cet appareil s il a t plong dans l eau m me partiellement Faites inspecter l appareil par un technicien qualifi et remplacez toute partie du syst me de contr le et toute commande qui ont t plong s dans l eau Poussez compl tement le bouton de contr le du gaz
48. ch in size GAS VENT DIRECTLY BELOW KEEP CLEAR OF ALL OBSTRUCTIONS PRE INSTALLATION Features Installation Options Residential Vented vertical and horizontal Manufactured mobile home Natural gas NG or propane LP Bedrooms Optional wall mounted or remote thermostat Venting This appliance can be vented with Secure Vent direct vent pipe Coaxial pipe diameters are 6 5 8 outer and 4 inner The combustion air for this stove is drawn from outside the house through the outer DV direct vent pipe Room air is not required for combustion When planning your installation select the correct length of vent pipe for your particular requirements Determine the minimum clearance to combustibles from the rear of the unit to the wall It is also important to note the thickness of the wall Before cutting the vent hole through the wall make sure that ALL vent and termination clearances see Page 22 will be met Electrical The standard fan motor requires 120 Volts AC for operation The stove is not dependent on the fan or an outside electrical supply to operate WARNING Electrical Grounding Instructions This appliance is equipped with a three prong grounding plug for your protec tion against shock hazard and should be plugged directly into a properly grounded three prong receptacle Do not cut or remove the grounding prong from this plug Other approved chimney brand is Simpson Dura Vent DV GS Millivolt Valve This app
49. e with the appliance burning insert a small flat bladed screwdriver into the tap and turn a half turn counterclockwise Cover the tap with the line from the manometer and check the pressure Close the tap gently but securely after completing the check The manifold outlet tap is to the right of the inlet tap To check manifold pressure with the appliance burning at the high burn setting insert a small flat bladed screwdriver into the tap and turn a half turn counterclockwise Cover the tap with the line from the manometer and check the pressure Again close the tap gently but securely after completing the check Check the taps for gas leaks with a gas leak test solution retighten if necessary If the pressure is not sufficient make sure the gas supply line is large enough the supply regulator is properly adjusted and the total gas load for the residence does not exceed the amount supplied Propane tanks are at pressures that will cause damage to valve com ponents Verify that the tanks have step down regulators to reduce the pressure to safe levels The appliance must be isolated from the gas supply piping system by closing its equipment shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1 2 psig 3 5 kPa The appliance and its appliance main gas valve must be disconnected from the gas supply piping system during any pressure testing of that system at test pressures in
50. e Product d damages repairs or inefficiency resulting from faulty installation or application of the Product HP is not responsible for inadequate fireplace system draft caused by air conditioning and heating systems mechanical ventilation systems or general construction conditions which may generate negative pressure in the room in which the appliance is installed Additionally IHP assumes no responsibility for drafting conditions caused by venting configurations adjoining trees or buildings adverse wind conditions or unusual environmental factors and conditions that affect the operation of the unit This 20 Year Limited Warranty covers only parts and labor as provided herein In no case shall IHP be responsible for materials components or construction which are not manufactured or supplied by IHP or for the labor necessary to install repair or remove such materials components or construction Additional utility bills incurred due to any malfunction or defect in equipment are not covered by this warranty All replacement or repair components will be shipped F O B from the nearest stocking IHP factory LIMITATION ON LIABILITY t is expressly agreed and understood that IHP s sole obligation and the purchaser s exclusive remedy under this warranty under any other warranty expressed or implied or in contract tort or otherwise shall be limited to replacement repair or refund as specified herein n no event shall IHP be liable for any inciden
51. e of the building and never be attached to a chimney serving a separate solid fuel or gas burning appliance Each direct vent gas appliance must use its own separate vent system Common vent systems are prohibited The Epic gas stove is recommended for use with Secure Vent pipe The appliances and vent manufacturers warranties will be voided and serious fire health or other safety hazards may result from any of the following actions Installation of any damaged direct vent component Unauthorized modification of the direct vent system Installation of any vent component part not approved or manufac tured by the approved vent manufacturer Installation otherthan as instructed by IHP and vent manufacturers instructions Residential and Mobile Home Installations These are the minimum pieces required Other parts may be required for your particular installation Minimum Components for Horizontal Installation Horizontal Termination Kit which includes e 1 6 5 8 x 6 Black Pipe 1 Riser Vent Terminal 1 Wall Penetration Heat Shield Wall Thimble 2 pcs 1 Decorative Wall Trim black 1 Tube Mill Pac Screws Optional Components 45 Elbow Vinyl Siding Shield for Riser Vent Terminal Vent Guard Snorkel Termination 36 Snorkel Termination 14 Wall Penetration Heat Shield Vent Considerations Twist lock procedure Four indentations on female ends of pipes and fittings are designed to
52. etach the two black wires from the back of the On Off switch disconnect the fan control wires and completely remove the control panel Remove the knob extensions from the valve controls Remove the log set and firebox liner panels see Firebox Liner Panels Log Set and Ember Installation Remove the two screws from the back of the burner Lift the left end of the burner and slide if off the orifice and shutter tube Remove the burner from the firebox From inside the firebox remove the right side burner support Then remove the seven socket head cap screws holding the cassette in place From inside the pedestal remove the four 3 8 nuts holding the back of the control panel pA 1 c Mark and unplug the remaining fan wire Remove the three screws securing the fan and set aside Remove the cassette assembly by carefully pulling the top cassette plate downward guiding the pilot assembly out of the firebox down into the pedestal area Once the pilot assembly is clear of the firebox remove the cassette from the pedestal Install the new converted or serviced cassette in the reverse order of removal All surfaces of the cassette must be sealed to the firebox to ensure an air tight seal The old gasket must be replaced with a new gasket All parts and wires must be correctly reinstalled to ensure safe and proper operation of the unit
53. excess of 1 2 psig 3 5 kPa Fuel Inlet Pressure Manifold Pressure Type Desired On Lo Fire A Also check the orifice size on the label on the igniter bracket It must be the correct size for the fuel and altitude Do not run propane tank dry Running the tank dry may cause a haz ardous condition due to pressure drop in empty tank Solid fuel is NOT to be used with this unit Check all connections for leaks using a gas leak solution Figure 28 LP and Natural Gas Supplies Your Epic gas stove is equipped from the factory for use with natural gas only as specified on the Safety Listing label attached to the appli ance This appliance can only be operated using propane gas LP if a certified fuel conversion kit provided by IHP is installed by a qualified service technician INSTALLER INSTRUCTIONS ATTACH SAFETY IN OPERATION WARNING LABELS It is required that the set of safety instruction labels that have been furnished with the fireplace be affixed to the operation and control points of the fireplace per the instructions on Page 7 It is the installers responsibility to ensure these warnings are properly affixed during installation These warning labels are a critical step in informing consumers of safe operation of this appliance NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 24 Operating Instructions Pre Lighting Checklist Be sure to check these items before the init
54. gn materials specifications and prices and also to discontinue colors styles and products Consult your local distributor for fireplace code information Printed in U S A 2014 Innovative Hearth Products P N 900110 00 REV B 01 2015 110 00 P900 TM INNOVATIVE HEARTH PRODUCTS 1508 Elm Hill Pike Suite 108 Nashville TN 37210
55. hen not connected to a properly installed and maintained venting system can result in carbon monoxide CO poisoning and possible death Control Panel Gas Control Off Pilot On f ay AM gum SIT Millivolt Gas Valve Flame Height Flame Height Control Knob HI LO Gas Control Knob Figure 29 Pilot On Off Flame Color and Behavior Your stove is designed for maximum heating efficiency Therefore upon lighting of the main burner the flames will be semitransparent or bluish After 10 20 minutes of operation the logs will heat up and the flames will become a yellow orange color Adjusting the appliance to cause the flames to turn orange sooner may result in poor combustion sooting and a hazardous situation See the drawing to the right showing proper flame appearance When testing for proper operation If an optional thermostat is installed adjust it to its highest temperature setting Visually determine that main burner gas is burning properly i e no floating lifting or flashback Ad just the primary air shutter s as required Check for proper main burner operation at both high and low flame Burner Flame Appearance Soot above Flame Tip Soot at Flame Tip No Soot at Flame Tip Dark Orange Flame Semi Transparent Yellow Flame Blue Flame Center Ports on Pan Burner Assembly No Blue Flame Center IMPROPERLY BURNING FLAME PROPERLY BURNING FLAME
56. ial lighting of the stove The stove gas label corresponds to the gas supply available that is natural gas for natural gas or LP gas for LP gas Gas pressure has been checked carefully see Page 23 All gas fittings have been checked for leaks All clearances to combustibles have been met see Page 13 All combustible materials have been removed from area in front of the stove All vented areas of the stove are unobstructed House is ventilated to clear initial paint curing odors see Page 26 All packaging materials have been removed from the fire box While stove is cool fingerprints or other marks have been cleaned from any gold or nickel surfaces with denatured alcohol and a soft cloth Marks left on these surfaces may become etched into the finish if not removed priorto burning the unit Firebox liner panels log set and embers have been installed The glass door is in place and is properly sealed OO 1 OOO 1 Lighting Instructions CAUTION HOT WHILE IN OPERATION DO NOT TOUCH KEEP CHILDREN FURNITURE GASOLINE AND OTHER LIQUIDS WITH FLAMMABLE VAPORS AWAY NEVER OPERATE UNIT WITH GLASS DOOR OFF OR ATTEMPT TO OPEN THE DOOR WHILE HOT CAUTION YOUR IHP GAS APPLIANCE MUST ALWAYS BE OPER ATED WITH THE GLASS DOOR IN PLACE The following is a copy of the operating and lighting instructions found with each stove FOR YOUR SAFETY READ BEFORE LIGHTING WARNING IF YOU DO NOT FOLLOW TH
57. installing a conversion kit regulator burner orifice and repositioning the slide orifice of the pilot Only a qualified service technician should perform the conversion Conversion Kit Please see instructions provided with conversion kit Cassette Removal CAUTION Label all wires prior to disconnection when servic ing controls Wiring errors can cause improper and dangerous operation ATTENTION Au moment de l entretien des commandes tiquetez tous les fils avant de les d brancher Des erreurs de c blage peuvent entra ner un fonctionnement inad quat et dangereux i Be sure the gas supply is shut off The electrical supply for the blower should be unplugged from both the wall and the Epic gas stove before beginning the conversion Disconnect back of pedestal by removing the four button head cap screws securing it slide back far enough to label and disconnect wires from the AC inlet plug Remove the white remote thermostat plug Completely remove back of pedestal from the Epic gas stove Disconnect the gas supply from the stove being careful not to apply pressure to the valve in the process Remove socket head cap screw securing the bottom of the right side door open label and remove the wires leading to the snap switch Remove the control panel containing the On Off switch by removing the four socket head cap screws securing it Pull the control panel out far enough to remove the orang e piezo igniter wire D
58. is required Also note that venting terminals shall not be recessed into a wall or siding If installing the termination cap on a wall covered with vinyl siding a vinyl siding standoff IHP SV4VS or Simpson 7950 or furring strips must be used to ensure that the termination cap is not recessed into the siding The horizontal run of vent should have a 1 4 6mm rise for every 12 of run toward the termination Never allow the vent to run downward This could cause high temperatures and may present the possibility of a fire Thelocation of the horizontal vent termination on an exterior wall must meet all local and national building codes and must not be blocked or obstructed For allowable external vent termination locations see Page 22 10 Allowable clearances from the vent pipe to combustible materials must be maintained See Page 13 for these clearances 11 Do not locate the termination cap where it may be blocked by shrub bery or snow Other approved chimney brand is Simpson Dura Vent DV GS NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Vertical Vent Installation Important Notes 1 All vertically terminated vent installations use 6 5 8 x 4 Secure Vent pipe 2 If the vent passes through a ceiling or floor afirestop Simpson 963 or IHP SV4BF is required 3 If the vent passes through the roof a roof flashing Simpson 943 or 9435 or IHP SV4FA or SV4FB and storm collar Simpson
59. lement parl e dans la r sidence du propri taire En cas de doute collez l tiquette en anglais 3 Sivousneparvenez pas localiserles tiquettes s il vous plait contactez IHP ou votre revendeur le plus proche pour recevoir IHP tiquettes d instructions de s curit suppl mentaires gratuitement tiquettes de remplacement n cat H8024 IHP IronStrike us com Remarque Le texte anglais est rouge sur un support transparent Le texte francais et espagnol est blanc sur un support noir DIAGRAMMES DES TIQUETTES DE S CURIT AVERTISSEMENT Vitre et foyer EXTREMEMENT CHAUDS Risque de br lures graves Toujours tenir les enfants l cart du foyer Figure B NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE COLOCACI N DE ADVERTENCIAS DE SEGURIDAD EN OPERACI N Se requiere que las etiquetas de instrucciones de seguridad incluidas con la chimenea se coloquen en el punto de operaci n y control de la misma Se debe colocar una etiqueta de instrucciones de seguridad en la placa del interruptor de pared desde el cual se enciende y se apaga la chimenea ver la Figura A o en el termostato de pared ver a Figura B y en el transmisor de control remoto Figura C si se usa Para completar correctamente la instalaci n de esta chimenea encuentrelas etiquetas adhesivas multiling es incluidas con las instrucciones de cuidado y operaci n y haga lo siguiente 1 Identifique el inter
60. liance is operated with a millivolt valve and therefore burns even during a power outage Fuel THIS APPLIANCE IS EQUIPPED FOR NATURAL GAS This appliance is equipped with an orifice sized for operation with natural gas For conversion to LP propane gas see instructions provided with the appliance Orifices and instructions necessary for LP propane conversion are pro vided in the gas conversion kit see Page 37for ordering information This appliance comes from the factory equipped to burn natural gas at a specified elevation Only IHP conversion kits can be used to convert from NG to LP or LP to NG Contact your IHP dealer for details Specifications Pipe Type direct vent Recommended manufacturer Secure Vent by IHP Diameter 6 5 8 x 4 for all installations Stove Packaging List The Epic gas stove comes with the following parts Stove Body with Burner Cassette and 150 CFM Blower 3 8 x 9 Gas Pipe 3 pc Firebox Liner Kit 4 pc Log Set Bag of Volcanic Stone Bag of Glowing Embers rockwool Bag of Flue Restrictors Firebox Liner Brackets and Tap tites Power Cord Installation and Operation Manual Trim Kits Gold Brushed Nickel or Black Nickel Trim Kit momo mo momo oe Epic 40 EPIC40 RATINGS NATURAL GAS LP GAS NATURAL GAS LP GAS 0 610 M O Manifold Pressure IN WC 3 5 1 7 10 0 5 4 3 5 1 7 10 0 5 4 Min Inlet Pressure IN WC O Unit factory equipped for 0 2000 FT 0 610 M In Canad
61. lications which may require vertical rise on the building exterior The components listed below come in a galvanized finish Most of the components are also available in a painted black finish Add a B to the end of the part number when ordering if a black part is desired Secure Vent by IHP 6 5 8 x 4 Pipe Part Number Description SVALC 6 Pipe Length SV4L12 12 Pipe Length SV4L24 24 Pipe Length SV4L36 36 Pipe Length SV4L48 48 Pipe Length SV4LA 6 Pipe Adjustable SV4LA12 12 Pipe Adjustable SV4FA Flashing 1 12 to 6 12 Roof Pitch SV4FB Flashing 7 12 to 12 12 Roof Pitch SV4RSM Wall Radiation Shield SV4E46 45 Elbow SV4E90 90 Elbow SV4VS Vinyl Shield Protector SV4FC Storm Collar SV4CGV Vertical Termination Cap SV4BF Firestop SV4CHC Horizontal Termination Cap SV4STC36 Snorkel Termination Cap 36 SV4STC14 Snorkel Termination Cap 14 SV4BM Wall Band Simpson Dura Vent GS 6 5 8 x 4 Pipe Part Number Description 908 6 Pipe Length 907 9 Pipe Length 906 12 Pipe Length 904 24 Pipe Length 903 36 Pipe Length 902 48 Pipe Length 911 11 to 14 5 8 Pipe Adjustable 942 Wall Thimble 940 Rnd Support Box Wall Thimble Cover 941 Cathedral Ceiling Support Box 943 Flashing 0 12 to 6 12 Roof Pitch 0435 Flashing 7 12 to 12 12 Roof Pitch 945 45 Elbow 990 90 Elbow 950 Vinyl Siding Standoff 953 Storm Collar 963 Ceiling Firestop 988 Wall Strap
62. ll clip included Receiver may be wall mounted or placed in the control compartment Includes white face plate Flame icon Low battery indicator Batteries included Remote Two Button Timer On Off Or Timer Mode H8860 RC S 1 Remote Control NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Cost Effective Solution Simple On Off operation Works with millivoltand low voltage electronic ignition controls Kit includes Remote and Receiver G Fire Remote Simple On Off H8840 KIT RC G FIRE Remote Control Wall Thermostat Wall surface mounted Thermostat or manual ON OFF operation Large LCD screen to display room and set temperature in F and C Connects to wall switch wire Wall Thermostat On Off and Thermostatic functions H8864 WS S TSTAT Wall Thermostat Wall Control 4 button timer with 30 60 120 0FF minutes Wall surface mounted Connects to wall switch wire Perfect for rental and resort applications Wall Switch Countdown Timer SAFETY LISTING LABEL MODEL SERIAL NO ge dee SERIE 5 MANUFACTURED BY IRONSTRIKE INNOVATIVE HEARTH PRODUCTS 1502 14TH ST NW HEAT FOR LIFE Report No Rapport n 14 161 AUBURN WA USA 98071 FACTORY EQUIPPED FOR NATURAL GAS IF CONTROL PANEL CONTRADICTS THIS LABEL UNIT FUEL TYPE HAS BEEN CONVERTED CET APPAREIL EST MUNI D QUIPEMENT POUR L USAGE DU GAZ NATUREL SI L TIQUETTE DU PA
63. lve the main burner will ignite CAUTION Lahel all wires prior to disconnection when servic ing controls Wiring errors can cause improper and dangerous operation ATTENTION Au moment de l entretien des commandes tiquetez tous les fils avant de les d brancher Des erreurs de c blage peuvent entra ner un fonctionnement inad quat et dangereux Gas Valve Wiring Terminals Thermopile Pilot Assembly Terminal 1 Terminal 2 Terminal 3 ON OFF Rocker Switch Thermostat or Remote Thermostat NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 27 28 MAINTENANCE AND SERVICING WARNING Turn off gas and electrical power to the fireplace and allow it to cool before cleaning or servicing the appliance CAUTION Wear gloves and safety glasses for protection while doing required maintenance Verify proper operation after servicing S assurer que l appareil fonctionne ad quatement une fois l entretien termin Maintenance Checklist The following should only be performed by a qualified service technician 1 Annual inspection should be made and the following checks performed O When unit is cool open glass viewing door and inspect burner for dirt soot and lint accumulations and remove if necessary If exces sive soot accumulation is present on burner have a qualified service technician adjust burner for proper combustion L1 Clean inside of glass viewing door with gas fireplace glass cleaner NE
64. m below shows all allowable combinations of straight vertical and offset to vertical vent configurations with vertical terminations The termination must fall within the shaded areas on the diagram Use the restrictor positions indicated Offsets may consist of two 90 elbows OR four 45 elbows The minimum termination height is 10 feet and the maximum is 30 feet NOTE Horizontal pipe requires 1 4 rise for every 12 of run Offsets must remain within max and min lines Vertical height is measured from the bottom of stove PAN J TA TS 28 TEE A A a 2 MIN OF VERTICAL PIPE REQUIRED BELOW TERMINATION VERTICAL HEIGHT FEET CDS EESE lt DE uu HORIZONTAL DISTANCE FEET Figure 26 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Exterior Horizontal Vent Termination Clearance Requirements See Item D in the Text Below Center Line Exterior Wall Termination Inside Corner Detail NE d a a Soffit Inside Corner Corner 9 in U S 12 in Canada DETAIL D Y Window RR Air Supply Inle
65. mbers tape for rigidity NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Glass Door WARNING e Do not attemptto substitute the materials used on these doors or replace cracked or broken glass e Handle this glass with extreme care Glass is susceptible to damage Do not scratch or handle roughly while reinstalling the glass door frame e The glass door s of this appliance must only be replaced as a complete unit as provided by the manufacturer Do not attempt to replace broken cracked or chipped glass separately e Do not attempt to touch the front enclosure glass with your hands while the appliance is in use e Do not use abrasive cleaners Never clean the glass when it is hot e DO NOT abuse glass door by striking or slamming shut CAUTION Do not operate the appliance with glass removed cracked or broken ATTENTION Ne pas utiliser l appareil si le panneau frontal en verre n est pas en place est craqu ou bris Only doors certified with the appliance shall be used Seules des portes certifi es pour cet appareil doivent tre utilis es Do not remove glass door while the appliance is hot Opening and Removing Door To replace the door 1 Shut off the main burner using the rocker switch 2 Shut off the pilot flame by turning the pilot knob clockwise to OFF 3 Facing the stove pull open the left side door and open the right side door by removing the socket head
66. mly in place with the charred side facing forward Figure 20 NOTE logs are designed to fit only one way For the ap pliance to function properly it is essential that the logs be installed correctly See below for an example of a correctly burning Epic gas stove NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Figure 21 Vent Installation Venting The Epic gas stove has been tested and listed as a direct vent heater system and is recommended for use with Secure Vent pipe Use only approved chimney brands with this appliance Important Read all instructions carefully before starting the installation Failure to follow these instructions may create a fire or other safety hazard and will void the warranty Be sure to check for specific clearances to combustible requirements on Page 13 Do not extend the venting system vertically or horizontally in excess ofthe distance prescribed on Page 21 Consult your local building codes before beginning the installation Always maintain the proper air spaces between the vent pipe and nearby combustibles to prevent a fire hazard Do not fill air spaces with insulation Be sure to check the venttermination clearance require ments from decks windows soffits gas regulators air supply inlets and public walkways as specified in these installation instructions on Page 22 and local building codes This gas stove and vent system must be vented directly to the out sid
67. n a fire or explosion D DO NOT use this appliance if any part has been under water Immediately call a qualified service technician to inspect the appliance and to replace any part of the control system and any gas control which has been under water several times until pilot is lit Continue to hold the knob in for about 30 seconds after the pilot is lit Release knob and it will pop back out Pilot should remain lit If it goes out repeat steps 4 8 holding knob in an additional 15 seconds after pilot is lit If knob does not pop out when released stop and immediately call your service technician or gas supplier Ifthe pilot will not stay lit after several tries turn the gas control knob to OFF and call your service technician or your gas supplier Gas Pilot Hood 9 After pilot is lit turn gas control counterclockwise to ON Knob P can only be turned ON if the knob has popped ie Thermopile igniter 10 To turn burner on tum ON OFF rocker switch to ON or set the thermostat Thermocouple to the desired temperature above room temperature D un 11 Adjust the flame height and heat output by turning the flame height knob clockwise for reduced flame and counterclockwise for full flame PILOT ASSEMBLY 12 on all electrical power to the appliance 13 Set the blower to the desired air flow after it turns on when the appliance reaches operating temperature WARNIN
68. n qualifi ou par le fournisseur de gaz SAFETY AND YOUR GAS STOVE See attached color flyer for proper color representation HOT GLASS WILL CAUSE BURNS DO NOT TOUCH GLASS UNTIL COOLED NEVER ALLOW CHILDREN TO TOUCH GLASS A barrier designed to reduce the risk of burns from the hot viewing glass is pro vided with this appliance and shall be installed for the protection of children and other at risk individuals Voir ci joint tract pour une bonne repr sentation de la couleur DANGER VITRE CHAUDE rs RISQUE DE BR LURES NE TOUCHEZ PAS UNE VITRE NON REFROIDIE NE LAISSEZ JAMAIS UN ENFANT DE TOUCHER LA VITRE L cran pare tincelles fourni avec ce foyer r duit le risque de br lure en cas de contact accidentel avec la vitre chaude et doit tre install pour la protection Des enfants et Des personnes risques Vea el volante adjunto para la representaci n de color adecuado PELIGRO EL VIDRIO CALIENTE CAUSAR QUEMADURAS USTED DEBE NUNCA TOCAR EL VIDRIO CALIENTE LOS NI OS DEBEN NUNCA TOCAR EL VIDRIO Una barrera dise ada para reducir el riesgo de quemaduras desde la mirilla vidrio caliente es proveida con este aparato y deber instalarse para la protecci n de los ni os y otros individuos en riesgo NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Safety and Your Gas Stove All parts of your IHP gas stove get Toutes les parties de votre po les au gaz IHP La s
69. nce ou autres liquides produisant des vapeur inflammables loin de l appareil Clearances are in accordance with local installation codes and the requirements of the gas supplier Les d gagements sont conformes aux codes d installation locaux et aux exigences du foumisseur de gaz This appliance is only for use with the type of gas indicated on rating plate This appliance is not convertible for use with other gases unless a certified kit is used Cet appareil doit tre utilis uniquement avec les types de gaz indiqu s sur la plaque signal tique Ne pas l utiliser avec d autres gaz sauf si un kit de conversion certifi est install WARNING Improper installation or use of this appliance can cause serious injury or death from fire burns explosion or carbon monoxide poisoning WARNING Failure to comply with these installation instructions will result in an improperly installed and operating appliance voiding its warranty 10 ORIFICE SIZE ALTITUDE ADJUSTMENT For altitudes above 2 000 feet In Canada 4 500 FT 1370 orifice should be de rated by 4 for every 1 000 feet to maintain the proper ratio of gas to air Improper orifice sizing may result in damage and un safe conditions Changing the orifice should only be done by a qualified service technician Contact your IHP dealer for proper orifice sizes see Page 30 for more information SMOKE DETECTORS Since there are always several potenti
70. ndle highlighted Figure 32 Quiet Operation As the Epic gas stove is burning a number of normal operational sounds may be heard The flow of gas through the gas valve and orifice may make a rushing or whistling noise If this noise is objectionable it can be reduced by turning down the flame Turning down the flame can reduce total heat output by more than 30 When the blower turns on the sound of rushing air may be heard The blower sounds may be reduced by adjusting the speed control located on the blower assembly Also a slight clicking sound may be heard as the gas valve or blower switch is turned on and off Paint Curing This stove has been painted with Stove Bright high temperature metallic paint It leaves the factory dry to the touch but completes the curing process as the stove is used To cure the paint burn the appliance four successive times for ten minutes each time with a five minute cool down between each firing Also some parts of the appliance may be lightly coated with machining oil Ventilate the house during these first firings as the paint and oil give off carbon dioxide and unpleasant odors It is recommended that persons sensitive to an imbalance in the indoor air quality avoid the appliance during the curing process Optional Wall Thermostat If an optional wall thermostat is to be installed install the thermostat per the manufacturers instructions provided with the thermostat Failure to follow manufact
71. ngase en contacto con IHP o con su distribuidor m s cercano IHP recibir instrucci n etiquetas de seguridad adicionales sin costo Juego de etiquetas de repuesto N de cat H8024 IHP IronStrike us com Nota La etiqueta en ingl s es transparente con texto rojo Las etiquetas en franc s y espa ol son negras con texto blanco DIAGRAMAS DE ETIQUETAS DE SEGURIDAD ADVERTENCIA Vidrio y chimenea EXTREMADAMENTE CALIENTES Riesgo de quemaduras graves Siempre mantenga a los ni os alejados de la chimenea Figure C INSTALLER INSTRUCTIONS ATTACHING SAFETY IN OPERATION WARNINGS It is the installers responsibility to ensure these warnings are properly affixed during installation These warning labels are a critical step in informing consumers of safe operation of this appliance ATTACHING SAFETY IN OPERATION WARNINGS It is required that the safety instruction labels fur nished with the fireplace be affixed to the operation and control point ofthe fireplace Asafety instruction label must be affixed to the wall switch plate where the fireplace is turned on and off See Figure A or wall thermostat See Figure B and if used on the remote control handheld transmitter Figure C To properly complete the installation of this fireplace locate the multi lingual adhesive labels provided with the Care and Operation Instructions and proceed as follows 1 Locate the wall switch or wall thermostat that controls the fireplace ve
72. nob has popped out 11 To turn burner on turn ON OFF rocker switch to ON or set the thermostat to the desired temperature above room temperature 12 Adjust the flame height and heat output by turning the flame height knob clockwise 5 reduced flame and counterclockwise w for full flame 13 Setthe blower to the desired air flow after it turns on when the appliance reaches operating temperature TO TURN OFF GAS TO APPLIANCE 1 Turnthe ON OFF rocker switch and or thermostat if installed to OFF 2 Turn off electric power to the appliance if service is to be performed 3 Turn gas control knob clockwise force to OFF Do not This appliance needs fresh air for safe operation and must be installed so there are provisions for adequate combustion and ventilation air See Installation and Operation Manual accompany ing appliance SHUTDOWN PROCEDURE To turn off the burner turn the rocker switch to OFF or adjust the thermostat if installed to a setting below room temperature The pilot will remain lit for future burner ignition For complete shutdown see TO TURN OFF GAS TO APPLIANCE above IMPORTANT NOTE When opening the lower door while the stove is burning pull on the handle located on the top side of the lower door Be cautious not to touch any part of the front door and firebox just above the lower door as those areas are hot WARNING Operation of this appliance w
73. nstallation 16 Vent Installation 17 21 VENENI eet 17 Residential and Mobile Home Installations 17 Vent Considerations 17 Vent Parts List 18 Horizontal Vent Installation 18 Vertical Vent Installation 19 Flie RestriClols ciao inicia aaia 20 Horizontal Terminations 21 Vertical Terminations 21 Horizontal Vent Termination Locations 22 Gas Line Installation 23 Gas Pressure 23 LP and Natural Gas Supplies 23 Attaching Safety In Operation Warnings 23 Operating Instructions 24 27 Pre Lighting 6 66 1151 24 Lighting Instructions 24 Flame Color and Behavior 25 Air Shutter Adjustment 26 Quiet
74. nstallation Gold amp nickel plating Replacement for two years from date of installation Excludes tarnishing Logs Replacement for one year from the date of installation against thermal breakage only Optional blowers amp remote controls Repair or replacement for one year from the date of installation Optional glass doors Repair or replacement for 90 days from the date of installation Tempered glass Replacement for one year from the date of installation Labor coverage Prevailing IHP labor rates apply for the warranty period of the component Parts not otherwise listed carry a 90 day warranty from the date of installation Whenever practicable IHP will provide replacement parts if available for a period of 10 years from the last date of manufacture of the Product IHP will not be responsible for a damages caused by normal wear and tear accident riot fire flood or acts of God b damages caused by abuse negligence misuse or unauthorized alteration or repair of the Product affecting its stability or performance The Product must be subjected to normal use The Product is designed to burn either natural or propane gas only Burning conventional fuels such as wood coal or any other solid fuel will cause damage to the Product will produce excessive temperatures and could result in a fire hazard c damages caused by failing to provide proper maintenance and service in accordance with the instructions provided with th
75. ntr le le fonctionnement du foyer en le faisant basculer de Marche Arr t et vice versa Nettoyez soigneusement la plaque murale de l interrupteur ou le thermostat mural pour liminer la poussi re et les traces de graisse ou d huile Collez l tiquette sur la surface de la plaque de l interrupteur mural qui contr le le foyer Figure A ou du thermostat mural Figure B Choisissez la langue qui est principalement parl e dans la r sidence du propri taire 2 Si une t l commande est utilis e pour contr ler le foyer nettoyez la soigneusement pour liminer la poussi re et les traces de graisse ou d huile Collez l tiquette sur le boitier de la t l commande Figure C Choisissez la langue qui est principale ment parl e dans la r sidence du propri taire 3 Sivousne parvenez pas localiser les tiquettes s il vous plait contactez IHP ou votre revendeur le plus proche pour recevoir IHP tiquettes d instructions de s curit suppl mentaires gratuitement Etiquettes de remplacement n cat H8024 IHP IronStrike us com Remarque Le texte anglais est rouge sur un support transparent Le texte fran ais et espagnol est blanc sur un support noir DIAGRAMMES DES TIQUETTES DE S CURIT AVERTISSEMENT _Vitre et foyer EXTREMEMENT CHAUDS Risque de br lures graves Toujours tenir les enfants l cart du foyer WARNING Figure A NOTE DIAGRAMS amp ILLUSTRATIONS ARE N
76. o Model Description 15524 Main Burer 36 NG 33 000 BTU NOTE The form numbers referenced are the part numbers of the instruction sheets included in kits NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 37 38 ACCESSORIES continued Thermostatic or Manual modes LCD Display Up to 9 hour Count down Timer Includes batteries Child lock Low battery indicator Receiver may be wall mounted or placed in the valve compartment Remote LCD Stat Thermostat On Off Cat No Model No H8861 RC S STAT Description Remote Control State of the art control with touch screen operation Backlit LCD display Wall mounted docking station for the trans mitter Thermostatic or manual ON OFF Programmable Weekday Weekend modes Flame icon and low battery indicator Receiver may be wall mounted or placed in the valve compartment Includes batteries Remote Touch Screen Thermostat On Off H8865 RC S TOUCH Flame and Heat modulation Includes solenoid for SIT millivolt valves Thermostatic manual or up to 9 hour Count down Timer modes 3 Fan speed settings Child lock Low battery indicator Wall clip included Includes batteries Remote With Hi Low Flame Millivolt Manual or up to 3 hr Countdown Timer modes LCD display Displays room temp in F or C Flame icon and low battery indicator Includes batteries Wa
77. ontaining the brick retaining brackets D and flue restrictors from the firebox 2 Install the rear firebox liner panel A bottom first and stand it flush against the rear of the firebox ensuring the pilot cutout is at the bottom directly above the pilot Figure 10 3 Install the left panel B bottom first and stand flush against left wall of firebox Repeat for right panel C against the right wall of firebox Figure 11 4 Using the included screws install the firebox liner retaining brackets D above the left and right firebox liner panels B and C Figure 13 Figure 15 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 16 Log Set and Ember Installation If logs are not installed according to the log installation instruc tions flame impingement and improper combustion could occur and result in soot and or excessive production of carbon monoxide CO a colorless odorless toxic gas The size and position of the log set is critical to achieve a safe reliable and attractive flame pattern Any attemptto use a differ ent log set in the fireplace will void the warranty and will result in incomplete combustion sooting and poor flame quality Packaging List Log set rear log A left rear log B left front log C center log D embers volcanic stone E glowing embers rockwool F 1 Carefully remove the logs from their packaging and ensure you have a complete set The logs are
78. opy ofthe warranty accompanying this manual Please read the warranty to be familiar with its coverage Retain this manual File it with your other documents for future reference Failure to comply with the installation and operating instructions provided will result in an improperly installed and operating appliance voiding its warranty Do not attempt to alter or modify the construction of the appliance or its components Any modification or alteration may void the warranty certification and listings of this unit IMPORTANT SAFETY AND WARNING INFORMATION INSTALLER THESE INSTRUCTIONS ARE TO REMAIN WITH THE HOME OWNER FOR YOUR SAFETY do not install or operate this appliance without first reading and understanding this manual Any installation or operation of the appliance deviating from that which is stated in this manual WILL void the warranty and may be hazardous IHP its employees or any of its representatives assume responsibility for any damages caused by an inoperable inad equate orunsafe conditionas aresultof any improper operation service or installation procedures whether direct or indirect DO NOT ATTEMPT TO SERVICE THE APPLIANCE YOURSELF Do not make any make shift compromises during installation Any modification or alteration may result in damage to the ap pliance or dwelling and will void the warranty certification and listings of this unit Failure to use manufacturer pr
79. or assembly Clearance to service regulator vent outlet 3 feet 91 cm 3 feet 91 cm J Clearance to non mechanical air supply inlet to building or the combustion air inlet to any other appliance Clearance to mechanical air supply inlet Clearance above paved sidewalk or paved ea located on public property Clearance under veranda porch deck or dea 6 in 15 2 cm for appliances lt 10 000 BTU hr 3kW 12 6 in 15 2 cm for appliances 10 000 BTU hr 3kW 9 in 30 cm for appliances gt 10 000 BTU hr 3kW and lt in 23 cm for appliances gt 10 000 BTU hr 3kW and lt 100 000 BTU hr 30kW 36 inches 91 cm for appliances 50 000 BTU hr 15kW 12 inches 30 cm for appliances gt 100 000 BTU hr 30kW gt 50 000 BTU hr 15kW 6 feet 1 8 meters 3 feet 91 cm above if within 10 feet 3 m horizon tally 7 feet 2 13 m t 7 feet 2 13 m 12 in 30 cm 12 in 30 cm In accordance with the current CAN CGA B149 1 National Gas and B149 2 Propane Installation Code Latest Editions n accordance with the current ANSI 2223 1 NFPA 54 National Fuel Codes Latest Edition A vent shall not terminate directly above a sidewalk or paved driveway which is located between two single family dwellings and serves both dwellings tOnly permitted if veranda porch deck or balcony is fully open on a minimum 2 sides beneath the floor Figure 27 22 NOTE DIAGRAMS amp ILL
80. ording to the diagram below Install the flue restrictor screws in their original holes in the top of the firebox Restrictor positions are based on tests run in a laboratory Flue Restrictor Adjustment Guidelines After the flue restrictors have been changed to the standard flue restrictor settings as shown in Figures 25 and 26 the burner flame appearance should be evaluated to determine if the A B C or D flue restrictor standard settings were the correct adjustment for variables in your installation Light the appliance and allow it to burn for 20 minutes on the high setting See Flame Color and Behavior on Pages 25 and 26 to determine if you have a proper burner flame appearance If the proper flame appearance cannot be achieved the flue restrictor may need to be changed to a dif ferent position A B C or D See the following guidelines to determine if you need to readjust the flue restrictors Before proceeding confirm the manifold and inlet gas pressure is correct primary air shutter is properly adjusted venting system connections are secure and not blocked and if you are at a high elevation ensure unit has been properly derated Symptoms Lack of Combustion Air If the symptoms listed below are present you may need to adjust the flue restrictor to more open position Flame appears yellow Floating Flames lazy ill defined quiet may roll e Sooting Pilot becomes yellow and appliance shuts down Symptoms
81. osition OFF ou ajustez le thermostat une temp rature en dessous de la temp rature ambiante La veilleuse restera allum e pour permettre un alummage ult rieur Pour un arr t complet Consultez la proc dure ci dessus POUR COUPER L ALIMENTATION EN GAZ DE L APPAREIL Innovative Hearth Products lronStrike Brand Gas Fireplaces Stoves and Inserts 20 Year Limited Warranty THE WARRANTY Innovative Hearth Products IHP 20 Year Limited Warranty warrants your lronStrike brand gas fireplace or insert Product to be free from defects in materials and workmanship at the time of manufacture The Product body and firebox carry the 20 Year Limited Warranty Ceramic glass carries the 20 Year Limited Warranty against thermal breakage only After installation if covered components manufactured by IHP are found to be defective in materials or workmanship during the 20 Year Limited Warranty period and while the Product remains at the site of the original installation IHP will at its option repair or replace the covered components If repair or replacement is not commercially practical IHP will at its option refund the purchase price or wholesale price of the IHP product whichever is applicable IHP will also pay IHP prevailing labor rates as determined in its sole discretion incurred in repairing or replacing such components for up to five years THERE ARE EXCLUSIONS AND LIMITATIONS to this 20 Year Limited Warranty as de
82. ovided parts variations in tech niques and construction materials or practices other than those described in this manual may create a fire hazard and void the limited warranty This gas appliance must be equipped for the proper fuel type and altitude at which it will be operated Any operation outside the parameters outlined in this manual may result in a hazard ous condition and will void the warranty Please carefully read the sections pertaining to these subjects and or be sure your appliance is properly equipped Any barrier grill panel or glass removed for service MUST be replaced prior to operating the appliance Tout cran ou protecteur retir pour permettre l entretien de l appareil doit tre remis en place avant de mettre l appareil en marche Never use solid fuels such as wood paper cardboard coal or any flammable liquids etc in this appliance Plated surfaces must be cleaned with glass cleaner and a clean soft cloth before firing the first time or fingerprints will remain permanently NEVER use brass polish to clean plated surfaces this will remove the plating CAUTION Hot while in operation Do not touch Severe Burns may result Keep children clothing furniture gasoline and other liquids having flammable vapors away ATTENTION L appareil est chaud lorsqu il fonctionne Ne pastoucher l appareil Risque de br lures graves Surveiller les enfants Garder les v tements les meubles l esse
83. que tous les membres de votre famille soient conscients du danger de br lure encouru Les surfaces de votre foyer deviennent EXTREMEMENT CHAUDES La vitre situ e l avant du foyer atteint des temp ratures EXTR MEMENT LEV ES et peut causer de graves blessures en cas de contact Tenez les enfants l cart du foyer lorsqu il fonctionne Surveillez attentivement les enfants dans les pi ces o un foyer est utilis afin d viter qu ils ne soient en contact avec la vitre Tenez tous les v tements les meubles l essence et tout autre liquide inflammable l cart du foyer M me apr s fermeture du gaz les surfaces du foyer restent extr mement chaudes Veillez coller les tiquettes de mise en garde relatives la s curit d utilisation l endroit o vous utilisez le foyer pour rappeler tous les utilisateurs les dangers li s aux temp ratures lev es voir pages 6 7 Lisez la section Informations importantes relatives la s curit page 5 FRENCH MUY CALIENTES Para evitar quemaduras y lesiones graves no quite el protector de malla o guardia de seguridad que evita el contacto directo con el vidrio Siga las instrucciones de seguridad a continuaci n y aseg rese de que todos en su hogar sepan acerca de este peligro de quemadura Las superficies de la chimenea se ponen MUY CALIENTES El vidrio delante de la chimenea
84. r toa st ses OO 5864 towing Emerson 48159 Touch Up Paint Metallic Black 12 oz aerosol 47490 Contact an IHP dealer to obtain any of these parts Please contact IHP for the phone number of your nearest IHP dealer WARNING Never use substitute materials Use of non approved parts can result in poor performance and safety haz ards A WARNING Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury AVERTISSEMENT Risque de dommages ou de blessures si les ne sont pas install es conform ment ces sch mas et ou si des pi ces autres que celles sp cifiquement approuv es avec cet appareil sont utilis es REPLACEMENT PARTS DIAGRAMS EPIC 33 40 EPIC33 40 NO DESCRIPTION NO DESCRIPTION NO DESCRIPTION 1 FRONT DOOR 12 SIDE DOOR 23 SMALL RELIEF DOOR 2 RIGHT BURNER SUPPORT 13 SIDE DOOR 24 SPRING RELIEF DOOR 3 LEFT BURNER SUPPORT 14 SNAP SWITCH 25 WASHER RELIEF DOOR 4 BURNER PAN LOG SET 15 TOP HINGE BRACKET 26 BOLT RELIEF DOOR 5 FIREBOX LINER PANELS 16 RELIEF DOOR ASSY LARGE 27 DOOR LATCH KIT 6 FIREBOX LINER PANELS 17 RELIEF DOOR LARGE 28 SPACER 7 FIREBOX LINER PANELS 18 TOP COVER 29 MAGNET AND BRACKET ASSY 8 FIREBOX LINER PANELS BRACKET 19 6 5 8 FLUE Adaptor 30 CONTROL DOOR 9 NAME PLATE 20 FLUE Adaptor GASKET 31
85. r orifice with the 36 NG orifice supplied in the optional orifice kit P N H5924 Pipe dope or other approved gas line sealant will need to be applied before inserting into bulkhead The foil sticker sup plied stating Epic NG33 will need to be affixed over the model name Epic NG40 on the serial number label Dimensions The gas line attaches to the gas valve at the lower left corner at the back of the stove Test all gas connections for leaks with a gas leak test solution Top View 17 432mm 20 508mm 23 1 2 m 597mm Figure 1 Front View 23 3 4 603mm 31 1 4 794mm Figure 2 Clearances to Combustibles Minimum clearances to combustible materials in inches millimeters Parallel Installation Back Wall 4 102 t 24 1 2 622mm Min 12 1 2 lt 318mm Min Side Wall Figure 3 Corner Installation 10 1 2 267mm Figure 4 Floor Protection A noncombustible hearth pad is not required This stove may be installed on a combustible surface Also the floor beneath the stove must be stable level hard and strong enough to support the stove without a tipping hazard Alcove dimensions The minimum width between the alcove side walls is 48 1219mm The minimum height of the alcove is 69 753mm and the maximum depth is 48 1219mm 69 753mm Min 48
86. r rocker switch or thermostat wir ing is not functioning Make sure thermopile is fully engulfed by the pilot flame Check thermopile with millivolt meter With pilot lit and the rocker switch and thermostat off the millivolt reading with the meter connected to valve terminals 1 and 2 should be after 2 minutes at least 325 If the thermopile lead connections are good at terminals 1 and 2 and readings are less than 325 replace faulty thermopile Wire Harness Diagram CAUTION Label all wires prior to disconnection when servicing controls Wiring errors can cause improper and dangerous operation ATTENTION Au moment de l entretien des commandes tiquetez tous les fils avant de les d brancher Des erreurs de cablage peuvent entrainer un fonctionnement inad quat et dangereux Blower Ring Lug Crimp Female Spade 1 4 Bea BLK 24 Male Spade 1 4 UTR GRN 24 Speed Control Switch BLK 5 Remote Thermostat Plug WHT24 Female Spade 1 4 Male Spade 1 4 BLK 18 1 1 BLK 16 4 Power Cord 6 ft Female Spade 1 4 Snap Switch Al Female Spade 1 4 Figure 39 NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE 34 REPLACEMENT PARTS Epic 33 40 EPIC33 40 Coin No PartNo ewm ar Somen 1588 Frevo Liner Paner Brane 35 50 H3138 Cassette Assembly NG CT TU NG 166 r
87. requent cleaning may be required due to excessive lint from carpeting bedding material et cetera It is imperative that control compartments burners and circulating air passageways of the appliance be kept clean See mainte nance instructions on Pages 28 30 L information de s ret importante 1 AVERTISSEMENT Ne pas utiliser l appareil si le panneau frontal en verre n est pas en place est craqu ou bris 2 Ne pas se servir de cet appareil s il a t plong dans l eau m me partiellement Faire inspecter l appareil par un technicien qualifi et remplacer toute partie du syst me de contr le et toute commande qui ont t plong es dans l eau 3 En raison des temp ratures lev es l appareil devrait tre install dans un endroit o il y a peu de circulation et loin du mobilier et des tentures 4 Les enfants et les adultes devraient tre inform s des dangers que posent les tem p ratures de surface lev es et se tenir distance afin d viter des br lures ou que leurs v tements ne s enflamment 5 On ne devrait pas placer de v tements ni d autres mati res inflammables sur l appareil ni proximit 6 Les jeunes enfants devraient tre surveill s troitement lorsqu ils se trouvent dans la m me pi ce que l appareil Les tout petits les jeunes enfants ou les adultes peuvent subir des br lures s ils viennent en contact avec la surface chaude Il est recommand d installer une barri re
88. rify the switch operates the fireplace by turning it on and off Clean the wall switch plate or wall thermostat thoroughly to remove any dust and oils Affix the label to the surface of the plate of the wall switch that controls the fireplace Figure A or the wall thermostat Figure B Choose the language primarily spoken in the home If unknown affix the English language label 2 Ifaremote controlis used to control the fireplace locate the transmitter and clean it thoroughly to remove any dust and oils Affix the label to the surface of handheld transmitter Figure C Choose the language primarily spoken in the home If unknown affix the English language label 3 If you are unable to locate the labels please contact IHP or your nearest IHP dealer to receive additional safety instruction labels free of charge Cat No H8024 Replacement Label Kit IHP lronStrike us com Note English is red text on clear label French and Spanish are white text on black label SAFETY LABEL DIAGRAMS Ay WARNING EXTREMELY HOT glass and fireplace Risk of Severe Burns ALWAYS KEEP_CHILDREN AWAY FROM FIREPLACE Illustrations are for example only Your accessories may be different Les illustrations sont par exemple uniquement Vos accessoires peuvent tre diff rents Las ilustraciones son s lo ejemplos Tu accesorios pueden ser diferentes Figure A APPOSITION DES MISES EN GARDE RELATIVES A LA SECURITE D UTILIS
89. ruptor o el termostato de pared quecontrolala chimenea verifique queelinterruptor opera la chimenea encendi ndola y apag ndola Limpie bien la placa del interruptor o el termostato de pared para quitar el polvo y aceite Pegue la etiquetaenlasuperficie dela placa del interruptor que controla la chimenea Figura A o en el termostato de pared Figura B Seleccione el idioma que m s se habla en la casa Si no sabe cu l es use la etiqueta en ingl s 2 Si se usa un control remoto para controlar la chimenea encuentre el transmisor y limpielo bien para quitar el polvo y aceite Pegue la etiqueta en la superficie del transmisor Figura Seleccione el idioma que m s se habla en la casa Si no sabe cu l es use la etiqueta en ingl s 3 Siustedesincapazdelocalizarlas etiquetas porfavor p ngase en contacto con IHP o con su distribuidor m s cercano IHP recibir instrucci n etiquetas de seguridad adicionales sin costo Juego de etiquetas de repuesto N de cat H8024 IHP lronStrike us com Nota La etiqueta en ingl s es transparente con texto rojo Las etiquetas en franc s y espafiol son negras con texto blanco DIAGRAMAS DE ETIQUETAS DE SEGURIDAD ADVERTENCIA Vidrio y chimenea EXTREMADAMENTE CALIENTES Riesgo de quemaduras graves Siempre mantenga a los ni os alejados de la chimenea Figure C Appliance Installation Service and Maintenance Notices WARNING Improper installation adjustment alteration
90. scribed herein COVERAGE COMMENCEMENT DATE Warranty coverage begins on the date of installation In the case of new home construction warranty coverage begins on the date of first occupancy of the dwelling or six months after the sale of the Product by an independent IHP dealer distributor whichever occurs earlier The warranty shall commence no later than 24 months following the date of product shipment from IHP regardless of the installation or occupancy date EXCLUSIONS AND LIMITATIONS This 20 Year Limited Warranty applies only if the Product is installed in the United States or Canada and only if operated and maintained in accordance with the printed instruc tions accompanying the Product and in compliance with all applicable installation and building codes and good trade practices This warranty is non transferable and extends to the original owner only The Product must be purchased through a listed supplier of IHP and proof of purchase must be provided The Product body and firebox carry the 20 Year Limited Warranty from the date of installation Vent components trim components and paint are excluded from this 20 Year Limited Warranty The following do not carry the 20 Year Limited Warranty but are warranted as follows Burner Repair or replacement for one year from the date of installation Gas components Repair or replacement for one year from the date of installation Gaskets Repair or replacement for one year from the date of i
91. service or maintenance can cause injury or property damage Refer to the owner s information manual provided with this appliance For assistance or additional information consult a qualified installer service agency or the gas supplier AVERTISSEMENT Une installation un r glage une modification une r paration ou un entretien mal effectu peut causer des dommages mat riels ou des blessures Voir la notice de l utilisateur qui accompgne l appareil Pour de l aide ou des renseignements suppl mentaires consultez un installateur un technicien agr ou le fournisseur de gaz Only trim kit s supplied by the manufacturer shall be used in the installation of this appliance Seules les trousses de garniture fournies par le fabricant doivent tre utilis es pour l installation de cet appareil These appliances must not be connected to a chimney or flue serving a separate solid fuel burning appliance Any change to this appliance and or its operating controls is dangerous Improper installation or use of this appliance can cause serious injury or death from fire burns explosion or carbon monoxide poisoning CARBON MONOXIDE POISONING Early signs of carbon monoxide poisoning are similar to the flu with headaches dizziness and or nausea If you have these signs obtain fresh air immediately Turn off the gas supply to the appliance and have it serviced by a qualified professional as it may not be operating correctly Some people are
92. t E Vent Terminal Area where Terminal is NOT permitted ss Minimum Clearances Clearances Camadianinstallation Installation US Installation Installation A Clearance above a T S veranda porch deck E 30 cm ee 30 cm or balcony Clearance to window or door that may be 6 in 15 2 cm for appliances lt 10 000 BTU Rr 3kW 6 in 15 2 cm for appliances lt 10 000 BTU hr 3kW opened 12 in 30 cm for appliances gt 10 000 BTU hr 3kW and lt 9in 23 cm for appliances gt 10 000 BTU hr 3kW and lt 100 000 BTU hr 30kW 36 inches 91 cm for appliances 50 000 BTU hr 15kW 12 inches 30 cm for appliances gt 100 000 BTU hr 30kW gt 50 000 BTU hr 15kW C Clearance to permanently closed window 12 inches 305 mm recommended to prevent window inches 229 mm recommended to prevent window condensation ondensation D Vertical clearance to ventilated soffit located 18 inches 458 mm inches 458 mm above the terminal within a horizontal distance of 18 in 458 mm from the center line of the terminal E Clearance to unventilated soffit 12 inches 30 cm 12 inches 30 cm Clearance to outside corner 5 inches 12 7 cm 5 inches AAA 7 cm H Clearance to each inside of center line extended 3 feet 91 cm within a height of 15 feet above the meter url feet 91 cm within a height of 15 feet above the meter above meter regulator assembly regulator regulat
93. t le bouton de r glage de la flamme dans les sens des aiguille d une montre x pour l abaisser et dans le sens contraire pour l augmenter 12 Mettez l appareil sous tension 13 Ajustez le ventilateur au volume d sir lorsque l appareil aura atteint la temp rature de fonctionnement 1 Fermez l interrupteur et ou le thermostat MARCHE ARRET 2 Coupez l alimentation lectrique de l appareil s il faut proc der l entretien 3 Tournez le bouton de commande du gaz dans le sens des aiguilles d une montre x OFF Ne le forcez pas Cet appareil a besoin d air frais pour op rer s critairement et doit tre install pour qu il y ait un apport en air suffisant R f rez vous aux manuels d entretien et d installation fournis avec l appareil AVERTISSEMENT Une installation inad quate un mauvais ajustement une alt ration ou toutes autres modifications inappropri s pourraient entrainer des blessures physiques et ou des dommanges mat riels R f rez vous au guide d utilisation fourni avec ce foyer Pour assistance ou information suppl mentaires contactez un installateur qualifi un agent de service ou un fournisseur de gaz Si vous op rez cet appareil sans qu il ne soit correctement raccord un conduit d vacuation vous pourriez risquer d tre empoisonn au monoxyde de carbone CO ce qui pourrait entra ner des cons quences grave ou la mort PROC DURE D ARR T 1 Pour arr ter le br leur mettre imus la p
94. tal or consequential damages caused by defects in the Product whether such damage occurs or is discovered before or after repair or replacement and whether such damage is caused by IHP s negligence IHP has not made and does not make any representation or warranty of fitness for a particular use or purpose and there is no implied condition of fitness for a particular use or purpose HP makes no expressed warranties except as stated in this 20 Year Limited Warranty The duration of any implied warranty is limited to the duration of this expressed warranty 0 one is authorized to change this 20 Year Limited Warranty or to create for IHP any other obligation or liability in connection with the Product Some states and provinces do not allow the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you The provisions of this 20 Year Limited Warranty are in addition to and not a modification of or subtraction from any statutory warranties and other rights and remedies provided by law INVESTIGATION OF CLAIMS AGAINST WARRANTY HP reserves the right to investigate any and all claims against this 20 Year Limited Warranty and to decide in its sole discretion upon the method of settlement To receive the benefits and advantages described in this 20 Year Limited Warranty the appliance must be installed and repaired by a licensed contractor approved by IHP Contact IHP at the address provided
95. urers instructions could result in a malfunction Pay special attention to the thermostat location requirements If the loca tion requirements are not adhered to the appliance erratic operation or failure may occur Do not mount the thermostat where it may be affected by Radiant heat from this appliance fireplaces sun or other heat sources Drafts or dead spots behind doors or in corners Hot or cold air from ducts NOTE DIAGRAMS amp ILLUSTRATIONS ARE NOT TO SCALE Operating Options Your stove comes equipped with an On Off rocker switch used to turn the burner on and off while the pilot light is on The switch is a round rocker switch located behind the main control panel door A millivolt wall thermostat or a remote control can be used to supple ment the rocker switch The gas valve is powered by millivolts generated by the pilot assembly This millivolt system is very sensitive to electrical resistance therefore make sure all connections are tight clean and free from corrosion Do not splice any millivolt wires Consult the table below to determine the proper gage of wire for the thermostat or wall switch connections This table refers to the total length of the wire out to the switch and back The thermostat must be a millivolt type A 24 volt furnace thermostat will not work Never hook up household current 120 Volts to the millivolt system It is not recommended to hook up any more than two switches to
96. urn off ALL electrical power to the appliance Make sure gas supply shut off cocks are open and ON OFF rocker switch is OFF If equipped with a thermostat set it to the lowest setting 5 Push in gas cock dial slightly and turn clockwise yy to OFF NOTE Dial cannot be turned from PILOT to OFF unless dial is pushed in slightly Do not force 6 Wait five 5 minutes to clear out any gas Then smell for gas including near the floor If you smell gas STOP Follow on this page If you don t smell gas go to the next step T Locate the pilot by looking through the hole under the right front log Blue flame will be seen when the pilot is lit 8 Turn the gas control knob counterclockwise Y to Pl LOT 9 Pushin control knob all the way and hold in Immediately light the pilot by triggering the piezo igniter pushing the button until pilot lights Continue to hold the control knob in for about 1 1 2 minutes after the pilot is lit Release knob and it will pop back out Pilot should remain lit If it goes out repeat steps 5 9 e If knob does not pop up when released stop and immedi ately call your service technician or gas supplier e If the pilot will not stay lit after several tries turn the gas control knob to OFF and call your service technician or gas supplier N A 10 After pilot is lit turn gas control counterclockwise y w to ON Knob can only be turned ON if the k
97. veilleuse B AVANT D ALLUMER la veilleuse reniflez tout autour de l appareil pour d celer une odeur de gaz Reniflez pr s du plancher car certains gaz sont plus lourds que l air et peuvent s accumuler au niveau du sol QUE FAIRE SI VOUS SENTEZ UNE ODEUR DE GAZ Ne pas tenter d allumer d appareil Ne touchez aucun interrupteur ne pas vous servir des t l phones se trouvant dans le b timent DANGER VOTRE APPAREIL AU GAZ IHP DOIT TRE OP R AVEC DES PORTES DE VERRE 1 ARR TEZ Lisez les instructions de s curit sur la portion sup rieure de cette tiquette 2 Ouvrez la porte d acc s la droite de l appareil Assurez vous que l alimentation en gaz est la position Ferm e OFF Si l appareil est quipp d un thermostat placez le la temp rature la plus basse Coupez l alimentation lectrique de l appareil Ferm e Enfoncez l g rement le bouton de contr le du gaz et tournez le dans le P E ni Qu sens des aiguilles d une montre w la position OFF NOTE Le bouton de contr le du gaz ne peut tre tourn de la position o o PILOT OFF sans qu une l g re pression ne soit appliqu e 5 Attendre cing 5 minutes pour laisser chapper tout le gaz Reniflez tout autour de l appareil y compris pr s du plancher pour d celer un odeur de gaz Si vous sentez une odeur de gaz ARRETEZ Passez l tape B des instructions de s curit sur la portion sup rieure de

Installation and Operation Manual - Epic - IronStrike

Contents

Download Pdf Manuals

Related Search

Related Contents