PANEL1125-675 Users Manual Version A1
Contents
1. PANEL 1125 675 Users Manual Gate A20 Option The default value is Fast The A20 signal is controlled by keyboard Normal controller or chipset hardware Fast Default Fast The A20 signal is controlled by Port 92 or chipset specific method Typematic Rate Setting This determines the typematic rate of the keyboard The default value is Disabled Enabled Enable typematic rate and typematic delay programming Disable typematic rate and typematic delay Disabled programming The system BIOS will use default value of these 2 items and the default is controlled by keyboard Typematic Rate Chars Sec This option refers to the number of characters the keyboard can type per second The default value is 6 6 6 characters per second 8 8 characters per second 10 Typematic Delay Msec This option sets the display time interval from the first to the second character when holding a key The default value is 250 250 750 1000 1000 msec 34 System Installation PANEL1125 675 User s Manual Security Option This item limits the access to the system and Setup or just to Setup The default value is Setup System The system will not boot and access to Setup will be denied if the incorrect password is entered at the prompt Setup The system will boot but access to Setup will be denied if the correct password is not entered at the prompt NOTE To disable security selec2. Soft off by PWRBTN This only works with the system using an ATX power supply It also allows user to define the type of soft power OFF sequence for the system to follow Instant Off This option follows the conventional manner default systems perform when power is turned OFF Instant off is a soft power OFF sequence requiring only the switching of the power supply button to OFF Upon turning OFF system from the power switch this option will delay the complete system power OFF sequence by approximately 4 seconds Within this delay period system will temporarily enter into Suspend Mode enabling you to restart the System at once Delay 4 Sec Wake Up Events An input signal on the network 2 awakens the system from a soft off state 46 System Installation PANEL1125 675 User s Manual A 6 PNP PCI Configuration This section describes the PCI bus system configuration PCI or Personal Computer Interconnect is a system which allows I O devices to operate at speeds nearing the speed of the CPU when communicating with its own special components This section covers some very technical items and it is strongly recommended that only experienced users should make changes to the default settings Phoenix AwardBIOS CMOS Setup Utility PnP PCI Configurations PNP OS Installed No Reset Configuration Data Disabled Menu Level gt Resources Controlled By Auto ESCD XIRQ Resources Press Enter Select Yes if you are XDMA Resources Pr
3. C to 85 C Humidity non condensing 5 95 B 1 5 International Standards SAFETY STANDARDS Designed to meet the following standards UL 60950 CSA 22 2 NO 234 VDE EN 60 950 EMI STANDARDS Designed to meet the following limits FCC docket 20780 curve B EN55022 B EN 61000 3 2 EMS STANDARDS Designed to meet the following standards EN61000 4 2 6KV contact discharge 8KV air discharge criteria A EN61000 4 3 10V m criteria A EN61000 4 4 2KV criteria A EN61000 4 5 2KV criteria A EN61000 4 6 3V criteria A EN61000 4 11 30 dips 10ms criteria B 60 dips 100ms criteria C 95 dips 5000ms criteria C 5A Power Supply Specifications PANEL1125 675 Users Manual B 2 Optional DC Power Supplies B 2 1 18 56V 100W DC Power Supply INPUT SPECIFICATIONS Input voltage range 418 56V pc e Input current 8A 18Vpc max Input protection FUSE 12A 125V OUTPUT SPECIFICATIONS Load Range RIPPLE amp NOISE eomy 120mV 100mV 150Mv MAX Output maximum 100 watts Forced air cooling The output voltage load regulation is less than the values in the above table by changing each output load 40 from 60 of rated load and keep another output at 60 of rated load ELECTRONIC CHARACTERISTICS Power efficiency 72 Typ While 48 Vpc input and full load condition RISE TIME 20mS MAX Over voltage protection Output over voltage protection 5V 5 8V 4 7 0V 12V 13 8V
4. 13 2A Seal POMS Seng Eoo Nana Kaki 15 2 5 Paralel Pahan a ak kebanan aab aab ia nak kah 15 UI EAS o akal aa a a a aaa aia aaa La a A EE RR 16 Zi SEMENG saanak ia ai HMM a E 16 28 Daka DOS quoted des dT a 16 29 System MODO coio t aan eh cadens anaa nain 17 2 9 1 Desktop Mounting eeee eee i7 2 9 2 Panel mount Kit Assembly sussss 17 2 9 8 Wall mount Kit Assembly seessse 18 2 9 4 VESA mount Kit Assembly ssss 18 CHAPTER 3 TOUCH SCREEN DRIVER INSTALLATION daauadasaxeuaaved a aria a ai NG a a AAK pi arana 19 sc My Specifications etc mn t 19 3 2 Driver Installation Windows 98 NT 2000 XP vii Windows XP embedded eene 20 33 Driver Installation DOS ternis 22 3 3 1 Using INSTALL EXE utility to instal PenMount Sofware AIVOT eias rinonce rnr A EE SEG ede aote setas 22 3 3 2 Identify the communication port and IRQ number 22 3 9 39 Do CalpratiO Megis sasangen aia NANA KENA hen 23 3 3 4 Initializing the PenMount driver 23 3 3 5 BeimotisttallOn cenis in b bai Ka aan vd irme bees 23 34 Drverinstallatone LINUX cec oo eet beet antah 24 APPENDIX A SBC83675 BIOS SETUP 26 AJ Standard CMOS Se lupi sssesesabasasas anangin asana 26 A 2 Advanced BIOS Features eeesseeesssl 31 A 3 Advanced Chipset Features ususuus
5. 36 A 4 Integrated Peripherals ssseeeeeee 40 A Power Management Setup sese 44 As PNP PGIGohfigutatlofi esce se eec aana nonton aaa 47 AT PO Health Status sasaosan aan ag aaa na eese eoe ea 49 A 8 Frequency Voltage Control susussss 50 AS Load Fail Safe Defaults ene 51 A 10 Set Supervisor User Password 52 APPENDIX B POWER SUPPLY SPECIFICATIONS BI ATTODW Power SUDDIV ciciessetereei o toto esse those ET asserts 53 BA Output Specifications erret iba 53 Bul 2 Input Specificallolis eniinn 53 B 1 3 General Specifications saisissent 54 B 1 4 Environmental Specifications 54 B 1 5 Intemational Standards wasa gaga ya ea sagen 54 B2 Optimal DG Power Sup NSS riaden eaaa an 55 B 2 1 418 56V 100W DC Power Supply 55 viii Table of Contents PANEL1125 675 User s Manual Chapter 1 Introduction The PANEL1125 675 equipped 12 1 high brightness LCD and supported Intel Pentium Ill processor 1 PCI ISA expansion slots and 8 channels DIO connection The paradigmatic industrial panel computer PANEL1125 675 is a complete full function and extreme cost effective industrial HMI controller The PANEL1125 675 fits in with Aluminum IP65 NEMA4 compliant front bezel and 350 nit high brightness 12 1 TFT LCD To provide flexible expansion
6. 675 User s Manual includes Floppy LS120 ZIP100 HDD0 3 SCSI CDROM USB Floppy USB CDROM USB HDD and LAN Boot Other Device This item allows the user to enable disable the boot device not listed on the First Second Third boot devices option above The default setting is Enabled Onboard Lan boot rom Choice Enable when you need boot on Lan Function Like PXE RPL Swap Floppy Drive This allows you to determine whether to enable Swap Floppy Drive or not When enabled the BIOS swaps floppy drive assignments so that Drive A becomes Drive B and Drive B becomes Drive A By default this field is set to Disabled Boot Up Floppy Seek During POST BIOS will determine the floppy disk drive type 40 or 80 tracks 360Kb type is 40 tracks while 720Kb 1 2MB and 1 44MB are all 80 tracks The default value is Enabled BIOS searches for floppy disk drive to determine Enabled if it is 40 or 80 tracks Note that BIOS cannot tell from 720K 1 2M or 1 44M drive type as they are all 80 tracks BIOS will not search for the type of floppy disk Disabled drive by track number There will be no warning message displayed if the drive installed is 360K Boot Up NumLock Status This option enables and disables the numberlock function of the keypad The default value is On Keypad functions confine with numbers i e left right arrow keys Keypad functions convert to special functions System Installation 33
7. Auto Primary Slave PIO Auto Secondary Master PIO Auto Secondary Slave PIO Auto Primary Master UDMA Auto Primary Slave UDMA Auto Secondary Master UDMA Auto Secondary Slave UDMA Auto Init Display First PCI Slot IDE HDD Block Mode Enabled Onboard FDD Controller Enabled Onboard Serial Port 1 3F8 IRQ4 Onboard Serial Port 2 2F8 IRQ3 UART 2 Mode Standard IR Function Duplex Half TX RX inverting enable No Yes Onboard Parallel Port 378 IRQ7 Onboard Parallel Mode Normal X ECP Mode Use DMA 3 X Parallel Port EPP Type EPP1 9 Onboard Legacy Audio Disabled Sound Blaster Disabled SB I O Base Address 220H SB IRQ Select IRQ 5 SB DMA Select DMA 1 MPU 401 Disabled MPU 401 I O Address 330 333H Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults 40 System Installation PANEL1125 675 User s Manual OnChip I DE ChannelO The integrated peripheral controller contains an IDE interface with support for two IDE channels Select Enabled to activate each channel separately I DE Prefetch Mode The onboard IDE drive interfaces supports IDE prefetching for faster drive accesses If you install a primary and or secondary add in IDE interface set this field to Disabled if the interface does not support prefetching Primary Master Slave PI O The four IDE PIO Programmed Input Output fields let you set a PIO mode 0 4 for each of the two IDE devices that the onboard
8. Exit Without Saving Esc Quit 2 Select Item F10 Save amp Exit Setup Load Fail Safe Defaults To load BIOS defaults value to CMOS SRAM enter Y If not enter N System Installation 51 PANEL 1125 675 Users Manual A 10 Set Supervisor User Password Either supervisor or user password or both of them can be set in this option The differences between them are 1 Supervisor password can enter and change the options of the setup menus 2 User password just can enter but do not have the right to change the options of the setup menus When this function is selected the following message will appear at the center of the screen for creating a password ENTER PASSWORD Type the password with eight characters at most and press Enter The password typed will now clear any previously entered password from CMOS memory Then confirm the password by typing the password again and pressing Enter Or not enter a pas sword and abort the selection by pressing Esc To disable the password by pressing Enter without typing in any password when the message Enter Password is showed Then message below will appear to confirm that the password has been disabled PASSWORD DISABLED Once the password is disabled the system will boot and enter Setup freely When a password is enabled it has to be typed to enter the Setup every time This prevents any unauthorized person from changing the syste
9. IDE interface supports Modes 0 through 4 provide successively increased performance In Auto mode the system automatically determines the best mode for each device The options available are Auto Mode 0 Mode 1 Mode 2 Mode 3 and Mode 4 Primary Master Slave UDMA Ultra DMA 66 100 implementation is possible only if your IDE hard drive supports it and the operating environment includes a DMA driver Windows 95 OSR2 or a third party IDE bus master driver If your hard drive and your system software support Ultra DMA 33 66 100 select Auto to enable BIOS support The options available are Auto Mode 0 Mode 1 and Mode 2 I nit Display First This item allows you to decide to active whether PCI Slot or AGP first The options available are PCI Slot AGP IDE HDD Block Mode This field allows your hard disk controller to use the fast block mode to transfer data to and from your hard disk drive Onboard FDD Controller Select Enabled if your system has a floppy disk controller FDC installed on the system board and you wish to use it If you install and in FDC or the system has no floppy drive select Disabled in this field The options available are Enabled Disabled System Installation 41 PANEL 1125 675 Users Manual Onboard Serial Port 1 Port 2 Select an address and corresponding interrupt for the first and second serial ports The options available are 3F8 IRQ4 2E8 IRQ3 3 E8 IRQ4 2F8 IRQ3 Disabled Auto UART 2 Mode The
10. n gt Baud Rate lt XXXX gt 3 3 5 Demonstration To demonstrate or test touch screen operation selecting 3 DRAWING TEST in PM BAT file of Utility Directory Drawing on screen The other demonstration program called ICECREAM EXE in the PENMOUNT directory can also be applied System Installation 23 PANEL1125 675 Users Manual 3 4 Driver Installation Linux If you want to install touch screen driver in the Linux please refer to the following figures 1 Open the file in Linux File etc rc local AAA after all the othar wh iWitialigation stuff in t full we U estule init stufi touch ver lockzsubays local rial command for Com3 and Comt seeting setserial sdew S2 port irq 18 setserial sdew 33 port Stet irq il 24 System Installation PANEL1125 675 Users Manual 2 The P 1125 675 reserves COM 3 for touch screen Please key in following words Set serial dev ttyS2 port 0x3e8 irq 10 set COMS as touch screen port tA D fi etc rc local n script will be executed safter all the othe init You can pat your om initializatios stuff in here if want to do the fall Sys U style init staff bi E E touch var lock subsys loca as seteerial comand for Gee N d setserial sdewiKS2Z part WAB ira 18 aw atal sew CS3 port Bae ire 1 ag 4 Save amp exit 5 Reboot System Installation 25 PANEL1125 675 Users Manual Appendix A SBC83675 BIOS Setup The board u
11. second serial port offers these infrared interface modes e IrDA e ASKIR I rDA compliant serial infrared port e Normal default value NOTE The UART Mode Select will not appear on the menu once you disable the setting of Onboard Serial Port 2 When UART Mode Select is set as ASKIR or IrDA the options RxD TxD Active and IR Transmittion delay will appear IR Function Duplex This item allows you to select the IR half full duplex function TX RX inverting enable This item allows you to enable the TX RX inverting which depends on different H W requirement This field is not recommended to change its default setting for avoiding any error in your system Onboard Parallel Port This item allows you to determine access onboard parallel port controller with which I O address The options available are 378H IRQ7 278H IRQ5 3BC IRQ7 Disabled Onboard Parallel Port Mode Select an operating mode for the onboard parallel printer port Select Normal unless your hardware and software require one of the other modes offered in this field The options available are EPP1 9 ECP SPP ECPEPP1 7 EPP1 7 ECP Mode Use DMA Select a DMA channel for the parallel port for use during ECP mode 42 System Installation PANEL1125 675 User s Manual Parallel Port EPP Type Select EPP port type 1 7 or 1 9 Onboard Serial Port 3 This item allows you to determine access onboard serial port 3 with which I O address The options available are 3F8H 2
12. stores Trademarks Acknowledgments AXIOMTEK is a trademark of AXIOMTEK Co Ltd IBM PC AT PS 2 VGA are trademarks of International Business Machines Corporation Intel and Pentium are trademarks of Intel Corporation MS DOS Microsoft C and QuickBASIC are trademarks of Microsoft Corporation VIA is a trademark of VIA Technologies Inc SST is a trademark of Silicon Storage Technology Inc UMC is a trademark of United Microelectronics Corporation Other brand names and trademarks are the properties of their respective owners Table of Contents DSC MS erate eters an deseruit dE ene d DILE ii Solel MOD OVE Sian iii Safety Precautions esci kaa aa pup rabia En eU bU A iv CHAPTER 1 INTRODUCTION aiisa rna casia ia a axi ain 1 Wel ESOSULOS coiere ox eaaa nag angen EE aa aga ana eus 2 1 2 Specifications eiui Dedit aa aaa aab Se ee 2 T1231 Malih GP DOS iia oto soo nag naa da 2 1 2 2 WO polt E E E wanen 3 1 2 9 System Speolflcalioli isan sasanak EN rrt da Aan 3 dac DIMENSIONS ascia eerta dax RE NER C ERE a C eA VLIR TES RUNS ie 5 LA Front View and VO OSIS aoreet ep ona iini te 6 1 4 1 Front VIQW eiiis sess sspe SERES GENG E EE EEE En NA 6 WA 2 WOMOUMCIS asra saa aana na a Ng ag ALE bag aaa a EE 7 MEE PRGA IST e ABEN A ANA EA NE kn 8 CHAPTER 2 SYSTEM INSTALLATION nnn 9 24 CPU and DRAM Installation atate 10 22 HDD Insiallation errem 11 23 Adden Gard InstallanGn uineis IR RF ENE EI IIa UR
13. to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measurers 1 Reorient or relocate the receiving antenna 2 Increase the separation between the equipment and receiver 3 Connect the equipment into an outlet on a circuit different from that to which the receiver is connected 4 Consult the dealer or an experienced radio TV technician for help Shielded interface cables must be used in order to comply with emission limits Safety Precautions Before getting started read the following important cautions 1 The PANEL1125 675 does not come equipped with an operating system An operating system must be loaded first before installing any software into the computer Be sure to ground yourself to prevent static charge when installing the internal components Use a grounding wrist strap and place all electronic components in any static shielded devices Most electronic components are sensitive to static electrical charge Disconnect the power cord from the PANEL 1125 675 before making any installation Be sure both the system and the external devices are turned OFF Sudden surge of power could ruin sensitive components Make sure the
14. 4 17 5V Power Supply Specifications 55 PANEL1125 675 Users Manual Short circuit protection When output short to ground the power supply will shutdown and auto recovery when fault condition has been removed Over load protection When output power over 115 to 180 of 100W the power supply will shutdown and auto recovery when fault condition has been removed MECHANICAL DATA Outline dimension W 84x 133 5xH 38 mm Cooling Natural cooling when exceed 80 watts load a 16CFM min DC fan required SAFETY This product is design to comply with the following standards UL 60950 3rd edition 2000 standard CSA C22 2 NO 60950 3rd edition 2000 standard TUV EN 60950 3rd edition 2000 standard IEC 60950 3rd edition 1999 standard EMKO TSE 74 SEC 207 94 standard EMC This product is design to comply with the following standards FCC CFR part 15 subpart J class B limit EN 50081 1 1997 emission standard EN 55022 1997 class B limit CNS 13438 class B EMS EN 50082 1 1997 immunity standard EN 6100 4 2 1995 ESD standard EN 6100 4 3 1996 RS standard EN 6100 4 4 1995 EFT standard EN 6100 4 5 1995 Surge standard EN 6100 4 6 1996 CS standard EN 6100 4 8 1993 H Power standard 56 Power Supply Specifications
15. 68 TFT T3 1280x1024 TFT T4 640x480 DSTN T5 800x600 DSTN T6 1024x768 DSTN T7 1024x768 TFT T8 640x480 TFT T9 800x600 TFT T10 1024x768 TFT T11 1280x1024 TFT T12 1400x1050 DSTN T13 800x600 DSTN T14 1024x768 DSTN T15 1280x1024 DSTN Display Type During Post This item selection includes VGA DEFAULT CRT LCD CRT LCD Display Type After Post This item selection includes VGA DEFAULT CRT LCD CRT LCD System Installation 29 PANEL 1125 675 Users Manual Halt On This field determines whether the system will halt if an error is detected during power up The system boot will halt on any error detected default Whenever the BIOS detects a All errors non fatal error the system will stop and you will be prompted The system boot will not stop for a But Keyboard keyboard error itwill stop for all other errors l The system boot will not stop for a But Diskette disk error it will stop for all other errors i The system boot will not stop for a But Disk Key keyboard or disk error it will stop for all other errors 30 System Installation PANEL1125 675 User s Manual A 2 Advanced BIOS Features This section is used to configure and improve the system and set up some system features according to the user s preference Phoenix AwardBIOS CMOS Setup Utility Advanced BIOS Features Virus Warning Disabled Item Help CPU Internal Cache Enabled External Cache Enabled Menu Level gt CPU L2 Cache ECC Checking
16. 75 provides three onboard serial ports installed on the back bottom side of the chassis For systems COM1 and COM2 are RS 232 and COM4 is RS 232 422 485 Each serial port is with 5V 12V power capabilities on both Pin 1 and Pin 8 ready to accommodate a wide array of serial devices such as fax modem scanner serial mouse and touch screen etc If the touch screen option is included its controller will share COM 1 COM to COM4 are all D SUB 9 pin connectors To connect any serial devices just plug in the device connector to the 9 pin D SUB In terms of transmission distance the RS 422 485 will perform better than RS 232 In this case COM4 is suggested to be set to RS 422 485 and the related jumpers have to be set correctly first see the system board User s Manual The RS 422 485 pin assignment is listed as follows Pin Signal Name R2 422 RS 485 DATA Ho connector No connector TKA DATA 0910203094095 060705809 KU M RX No connector oie Sonnector No connector 8 No connector No connector 9 GND GND i 2 5 Parallel Port The printer interface is a 25 pin D SUB connector To connect any parallel device just plug in the device connector to the 25 pin D SUB System Installation 15 PANEL 1125 675 Users Manual 2 6 VGA The PANEL1 125 675 has an analog RGB interface connector It is able to connect to an expansion CRT monitor and the system can display on both the flat panel and the C
17. ANEL11 25 675 is designed for panel mount application To mount the PANEL 1125 675 the standard set of mounting kit included in the system packaging is needed Please refer to the following figure System Installation 17 PANEL 1125 675 Users Manual P4 N y N 2 9 3 Wall mount Kit Assembly The PANEL11 25 675 provides the kit for wall mount application To mount the PANEL 1125 675 the standard set of mounting kit included in the system packaging is needed Please refer to the following figure 1 Secure 4 screws to fix wall mount kit in the P 1125 675 2 Fix the P 1125 675 in the wall 2 9 4 VESA mount Kit Assembly The PANEL11 25 675 provides the kit for VESA ARM application To mount the PANEL 1125 675 the standard set of mounting kit included in the system packaging is needed Please refer to the following figure 1 Secure 4 screws to fix VESA ARM kit in the P 1125 675 2 P1125 775 offers 4 VESA standard holes 75x75mm You can select VM 101 for VESA ARM clamp type or VM 101S for VESA ARM wall mount type 18 System Installation PANEL1125 675 User s Manual Chapter 3 Touch Screen Driver Installation 3 1 Specifications Resolution 1024 x 1024 10 bit A D converter inside Powerinput 5V to 12VDC Power Consumption 12V 27mA i where i v touch screen sheet R 5V 23mA i where i v touch screen sheet R Board Size Size 6 0 x 2 0 cm Support 900 to 2700 screen rotation Static Pr
18. Cache Integrated in CPU Bus Clock 66 100 133 MHz Watchdog Timer Generates a system reset or NMI by jumper selectable software programmable Time interval 64 levels 0 5 8 5 80 50 800 100 1600 seconds Introduction PANEL1125 675 User s Manual 1 2 2 I O port Standard I O 4 x serial ports with 1x Keyboard Interface eae a ee an lx 1x PS 2 Mouse Interface oe a jumper 2x USB Ports 1 1 compliant selectable 1 x parallel port SPP EPP ECP Digital I O Input x 4 Output x 4 Ethernet Realtek RTL 8100C PCI Bus 10 100M Base T Wake On LAN RJ 45 interface equipped Audio AC 97 Codec 32 bit Sound Blaster and sound Pro compatible 16 bit stereo ADC and DAC PC97 PC98 and WHQL specifications Full duplex operation for simultaneous record and playback Internal MIC in Line in Speaker Line out interface reserved VGA Flat Panel Controller VIA Twister chip with integrated S3 Pro Savage4 2D 3D Video accelerator 8 16 32MB frame buffer sharing system memory Supports up to 1280 X 1024 256 color resolution on noninterlaced CRT monitors and 1024 x 768 16 bit color on LCD panel monitors 1 2 8 System Specification 12 1 TFT with 800 x 600 resolution NEMA 4 12 sealed front panel Slim floppy disk drive Heat dispensing design One free slots for PCI or ISA expansion This slot only comes standard with the riser card assembly Net weight 4 3 Kgs Introduction 3 PAN
19. EL 1125 675 Users Manual Dimension main body size 361 5 x 300 x 121 mm Operating Temperature Range 0 C 45 C Relative Humidity 10 90 40 C non condensing 4 Introduction PANEL1125 675 User s Manual 1 3 Dimensions The following diagrams show the dimensions and outlines of PANEL11 25 675 Introduction 5 PANEL 1125 675 Users Manual 1 4 Front view and I O Outlets 1 4 1 Front View The figure below shows the features and controls on the PANEL11 25 675 front panel 1 LCD ON OFF 2 LED Red Backlight OFF LED Green Backlight ON 3 Brightness DOWN 4 Brightness UP 6 Introduction PANEL1125 675 User s Manual 1 4 2 O Outlets The following figure shows the I O locations of the PANEL11 25 675 Most of the I O connectors are located on the back panel of the PANEL1125 675 000000 900000 ee ee 1 Slim type CD ROM 10 2 Slim FDD 11 3 Power Switch 12 4 AC inlet 13 5 LAN RJ45 14 6 USB v1 1 15 T USB v1 1 16 Line Out 17 Line In 18 Introduction MIC Keyboard Mouse VGA Port PRN Parallel Port DIO 8 Channel Digital Inputs Outputs COM2 COMS COM4 PANEL1125 675 Users Manual 1 5 Package List When you receive the P1125 675 there are following items in the package If you cannot find it please contact AXIOMTEK distributors PANEL1125 675 1 Panel mount kit 4 Panel mount screw 4 AC power cord 1 CPU Cooler 1 HDD br
20. Enabled Processor Number Feature Enabled Allows you to Quick Power On Self Test Enabled choose the VIRUS First Boot Device HDD O warning feature Second Boot Device Floppy for IDE Hard disk Third Boot Device LS120 boot sector Boot Other Device Enabled protection If this Onboard Lan boot Rom Disable Swap Floppy Drive Disabled function is enable Boot Up Floppy Seek Enabled and someone Boot Up NumLock Status On attempts to write Gate A20 Option Fast data into this area Typematic Rate Setting Disabled BIOS will show Typematic Rate Chars Sec 6 a warning Typematic Delay Msec 250 message on Security Option Setup screen and alarm OS Select For DRAM gt 64MB Non OS2 beep Video BIOS Shadow Enabled C8000 CBFFF Shadow Disabled CC000 CFFFF Shadow Disabled D0000 D3FFF Shadow Disabled D4000 D7FFF Shadow Disabled D8000 DBFFF Shadow Disabled DC000 DFFFF Shadow Disabled Small Logo EPA Show Disabled VY Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults System Installation 31 PANEL1125 675 Users Manual Virus Warning This item protects the boot sector and partition table of the hard disk against accidental modifications If an attempt is made the BIOS will halt the system and display a warning message If this occurs the user can either continue the operation or run an anti virus program to locate and remove the problem NOTE
21. F8H 3E8H 2E8H Disabled Serial Port 3 Use IRQ Select a corresponding interrupt for the 3 serial port The options available are IRQ10 11 3 4 5 7 9 Onboard Serial Port 4 This item allows you to determine access onboard serial port 4 with which I O address The options available are 3F8H 2F8H 3E8H 2E8H Disabled Serial Port 4 Use IRQ Select a corresponding interrupt for the 4 serial port The options available are IRQ10 11 3 4 5 7 9 System Installation 43 PANEL1125 675 Users Manual A 5 Power Management Setup The Power Management Setup is to save energy of the system effectively It will shut down the hard disk and turn OFF video display after a period of inactivity Phoenix AwardBIOS CMOS Setup Utility Power Management Setup ACPI Function Power Management PM Control by APM Video Off Option Video Off Method MODEM Use IRQ Soft Off by PWRBTN Wake Up Events VY2 Move Enter Disabled Press Enter Yes Menu Level gt Suspend gt Off V H SYNC Blank 3 Instant Off Press Enter Item Help Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults ACPI Function This itemis to enable disable the Advanced Configuration and Power Interface ACPI The choice Enabled Disabled Power Management This itemis to select the Power Management mode The choice User Define Min Saving Max Saving PM Control by APM When enab
22. Many disk diagnostic programs which attempt to access the boot sector table can cause the virus warning Thus disable the Virus Warning feature while running any of these programs CPU Internal Cache External Cache Cache memory is additional memory that is much faster than conventional DRAM system memory CPUs from 486 type and up contain internal cache memory and most but not all modern PCs have additional external cache memory When the CPU requests data the system transfers the requested data from the main DRAM into cache memory for even faster access by the CPU These items are used to enable speed up memory access or disable the cache function By default these are Enabled CPU L2 Cache ECC Checking When enabled this allows ECC checking of the CPU s L2 cache By default this field is Enabled Processor Number Feature When a Pentium III CPU is installed the system automatically detects it and displays this item Quick Power On Self Test This option speeds up Power On Self Test POST after turning onthe system power If it is set as Enabled BIOS will shorten or skip some check items during POST The default setting is Enabled Enable Quick Enabled POST Disabled Normal POST First Second Third Boot Device These items allow the selection of the 1 2 and 3 devices that the system will search for during its bootup sequence The wide range of selection 32 System Installation PANEL1125
23. PANEL1125 675 12 1 High Brightness Industrial Panel Computer User s Manual Disclaimers The information in this manual has been carefully checked and is believed to be accurate AXIOMTEK Co Ltd assumes no responsibility for any infringements of patents or other rights of third parties which may result from its use AXIOMTEK assumes no responsibility for any inaccuracies that may be contained in this document AXIOMTEK makes no commitment to update or to keep current the information contained in this manual AXIOMTEK reserves the right to make improvements to this document and or product at any time and without notice No part of this document may be reproduced stored in a retrieval System or transmitted in any form or by any means electronic mechanical photocopying recording or otherwise without the prior written permission of AXIOMTEK Co Ltd Copyright 2005 by AXIOMTEK Co Ltd All rights reserved January 2005 Version A1 Printed in Taiwan Safety Approvals CEMarking FCCClassA FCC Compliance This equipment has been tested and complies with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation If not installed and used in accordance with proper instructions this equipment might generate or radiate radio frequency energy and cause harmful interference
24. PANEL1125 675 is properly grounded The brightness of the flat panel display decreases with usage However hours of use vary depending on the application environment Turn OFF the system power before cleaning Clean the System using a cloth only Do not spray any liquid cleaner directly onto the screen The PANEL1125 675 may come with or w o a touchscreen Although the touchscreen is chemical resistant it is recommended that you spray the liquid cleaner on a cloth first before wiping the screen In case your system comes without the touchscreen you must follow the same procedure and not spray any cleaner on the flat panel directly Avoid using sharp objects to operate the touchscreen Scratches on the touchscreen may cause malfunction or internal failure to the touchscreen The flat panel display is not susceptible to shock or vibration When assembling the PANEL1125 675 make sure it is securely installed for maintenance is a must only a trained technician is allowed to do so Integrated circuits on computer boards are sensitive to static electricity To avoid damaging chips from electrostatic discharge observe the following precautions e Before handling a board or integrated circuit touch an unpainted portion of the system unit chassis for a few seconds This will help to discharge any static electricity on your bogy e When handling boards and components wear a wrist grounding strap available from most electronic component
25. RT simultaneously 2 7 Ethernet The PANEL1125 675 provides an NE2000 compatible Ethernet RJ 45 interface For network connection just plug in one cable end of the PANEL 1125 675 100 Base T Hub into the standard RJ 45 connector The pin assignment of the RJ 45 is listed below RJ 45 Connector Pin Assignment 12345678 Tx Data transmission positive Tx Data transmission negative Rx Data reception positive RJ 45 Rx Data reception negative Not use 2 8 Digital I Os The PANEL1125 675 provides a digital I O of 8 channel inputs outputs for simple automation control For example it can be used to control the opening and closing of the cash drawer on a POS system It can also be used for UPS control It comes with a 15 pin D SUB connector and its pin position and pin assignment is shown on the following page Digital 1 0 Pin Assignment OUT P9 T 8102030105 INT 06070809010 IN2 011012 0 13014 015 IN3 INA GND Ii UE Ta ER 16 System Installation PANEL1125 675 Users Manual 2 9 System Mounting There are 4 mounting ways for the PANEL1125 675 Desktop Wall Panel and VESA mounting ways 2 9 1 Desktop Mounting If you select the desktop application you can t use the wall mount kit at the same time The standard set of desktop kit is included in the System packaging Please refer to the following figure Install desktop kit in the P 1125 675 2 9 2 Panel mount Kit Assembly The P
26. acket kit 1 HDD anti vibration rubber 4 HDD screw 8 Desktop kit 1 10 Drive CD 1 o oN POP a ARI 8 Introduction PANEL1125 675 User s Manual Chapter 2 System Installation This chapter describes the system installation and the cable connection to the I O connectors See system board User s Manual that came with your PANEL PC packaging for more details Sections in this chapter includes e CPU e 3x Serial e Desktop e DRAM Ports Wall Panel VESA e e HDD Parallel Port mount Add on card e VGA e Ethernet Digital I O The PANEL1125 675 has a Pentium III CPU board with a free PCI ISA slot System performance can be increased by upgrading to a higher performance CPU higher capacity DRAM modules and hard disk drive The user can use the I O ports located at the backside of the chassis to connect external peripheral devices such as a monitor serial devices parallel printer etc NOTE Make sure the power cord is disconnected before any installation To install any internal device such as CPU DRAM and HDD take out the rear chassis cover first System Installation 9 PANEL 1125 675 Users Manual 2 1 CPU and DRAM Installation The standard PANEL1125 675 system was designed Pentium Ill Celeron amp level CPUs The built in CPU board SBC83675 provides one 168 pin DIMM socket that supports system memory up to 512MB When upgrading the CPU or DRAM refer to the following illustration and instructi
27. are the control keys for the use of this menu The F1 key can be pressed in each item field to display the relevant information for help The memory display at the lower right hand side of the menu is read only It will adjust automatically according to the memory changed The following pages describe each item of this menu System Installation 27 PANEL 1125 675 Users Manual Date The date format is day date month year Press F3 to show the calendar The day of week from Sun to Sat determined day by the BIOS is read only The date from 1 to 31 or the maximum allowed date in the month can key in the numerical function key The month Jan through Dec The year depends on the year of BIOS Time The time format is hour minute second accepting either function key or numerical key The time is calculated based on the 24 hour military time clock For example 1 p m is 18 00 00 IDE Primary Master Primary Slave Secondary Master Secondary Slave This category identifies the type of the channel that is installed in the computer There are 45 predefined types and 2 user definable types for Enhanced IDE BIOS Type 1 to Type 45 are predefined Type User is user definable Press lt PgUp gt lt gt or PgDn to select a numbered hard disk type or type the number and press Enter Note that the specifications of the drive in the system m ust match with the drive table The ha
28. each system interrupt a type depending on the type of device using the interrupt DMA Resources When resources are controlled manually assign each system DMA channel as one of the following types depending on the type of device using the interrupt 1 Legacy ISA Devices compliant with the original PC AT bus specification requiring a specific DMA channel 2 PCI ISA PnP Devices compliant with the Plug and Play standard whether designed for PCI or ISA bus architecture The default value is PCI ISA PnP PCI VGA Palette Snoop Leave this field at Disabled The choice Enabled Disabled Assign I RQ For USB VGA This item is to enable or disable the IRQ assignment for USB VGA The options available are Enabled Disabled 48 System Installation PANEL1125 675 User s Manual A 7 PC Health Status This section is to monitor the current hardware status of the CPU fan speeds and the core voltages This is available only if there is hardware monitoring mechanism onboard Phoenix AwardBIOS CMOS Setup Utility PC Health Status Current CPU FAN1 Speed Current CPU FAN2 Speed Vcore 2 5V 3 3V 5V 12V VY Move Enter Select PU PD Value F10 Save ESC Exit Fl General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Current CPUFAN Speed These optional and read only fields show the current speeds in RPM revolution per minute for the CPU fan and chassis fan as monitored by the hardwa
29. ensate for the speed differences between the CPU and the PCI bus When Disabled the writes are not buffered and the CPU must wait until the write is complete before starting another write cycle PCI Dynamic Bursting This itemis to enable disable the PCI dynamic bursting function PCI Master 0 WS Write When Enabled writes to the PCI bus are executed with zero wait states PCI Delay Transaction The chipset has an embedded 32 bit posted write buffer to support delay transactions cycles Select Enabled to support compliance with PCI specification version 2 1 The default setting is Disabled PCI 2 Access 1 Retry When Disabled PCI 2 will not be disconnected until access finishes default When Enabled PCl 2 will be disconnected if max retries are attempted without success AGP Master 1 WS Write When Enabled writes to the AGP Accelerated Graphics Port are executed with one wait states 38 System Installation PANEL1125 675 User s Manual AGP Master 1 WS Read When Enabled read to the AGP Accelerated Graphics Port are executed with one wait states System Installation 39 PANEL1125 675 Users Manual A 4 Integrated Peripherals This option sets the hard disk configuration mode and port Phoenix AwardBIOS CMOS Setup Utility Integrated Peripherals OnChip IDE ChannelO Enabled Item Help OnChip IDE Channel1 Enabled IDE Prefetch Mode Enabled Menu Level gt Primary Master PIO
30. ess Enter using a Plug and play capable operating PCI VGA Palette Snoop Disabled system select No if Assign IRQ For VGA Enabled you need the BIOS to Assign IRQ For USB Enabled configure non boot devices y Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults PNP OS Installed This itemis to determine install PnP OS or not The options available are Yes and No Reset Configuration Data Normally this field is Disabled Select Enabled to reset Extended System Configuration Data ESCD When exiting Setup or installed a new add on the system reconfiguration has caused such a serious conflict thatthe operating system cannot boot The options available are Enabled and Disabled Configure all of the boot and Plug and Play compatible devices However this capability means absolutely nothing unless you are using a Plug and Play operating system such as Windows 95 The options available are Auto and Manual System Installation 47 PANEL 1125 675 Users Manual Resource controlled by The Award Plug and Play BIOS has the capacity to automatically configure all of the boot and the Plug and Play compatible devices However this capability means absolutely nothing unless using a Plug and Play operating system such as Windows 98 The options available are Auto and Manual I RQ Resources When resources are controlled manually assign
31. hoices are 15M 16M and Disabled P2C C2P Concurrency This item enables or disables the PCI to CPU and CPU to PCI concurrency By default this field is set to Enabled System BI OS Cacheable Selecting Enabled allows caching of the system BIOS ROM at F0000h FFFFFh resulting in better system performance However if any program writes to this memory area a system error may result The choice Enabled Disabled Video RAM Cacheable Selecting Enabled allows caching of the A B segment resulting in better system performance The choice Enabled Disabled AGP Aperture Size The field sets aperture size of the graphics The aperture is a portion of the PCI memory address range dedicated for graphics memory address space Host cycles that hit the aperture range are forwarded to the AGP without any System Installation 37 PANEL 1125 675 Users Manual translation The choice 4M 8M 16M 32M 64M 128M and 256M OnChip USB This should be enabled if the system has a USB installed on the system board and the USB will be used Even when equipped if a higher performance controller is added this feature should be disabled The choice Enabled Disabled USB Keyboard Support Select Enabled if the system contains a Universal Serial Bus USB controller and you have a USB keyboard The choice Enabled Disabled CPU to PCI Write Buffer When this field is Enabled writes from the CPU to the PCI bus are buffered to comp
32. ibration To adjust the display with touch panel click Calibration and follow the calibrate point to do calibration there are five points on screen for calibration 6 Press OK System Installation 21 PANEL 1125 675 Users Manual 3 3 Driver Installation DOS 3 3 4 Using INSTALL EXE utility to install PenMount software driver 1 Insert Driver CD and select the D PANEL1125 675 Driven Touch screen DOS Install exe 2 Press ENTER key to install the drivers to drive C or use keyboard to key in the hard disc drive that you plan to install the driver 3 The driver will ask Do you want to modify your Autoexec bat to initialize PenMount Y N Suggest you choose YES for generating the initialization instructions in AUTOEXEC BAT files Then follow up the instructions to complete the installation 3 3 2 Identify the communication port and IRQ number 1 Forthe first time installation or changing PenMount Touch Screen s COM port use PMDETECT e g C PENMOUNT PMDETECT to check the COM port and IRQ number PMDETECT will save the correct data to PMOUSE CFG file for further use The driver detects your communication COM port and IRQ number from COM1 IRQ4 COM IRQ3 COMS to COM4 IRQ15 PenMount driver can find the COM port and IRQ number automatically The screen will then show PenMount is initialized successfully Create file bmouse cfg Success PenMount internal settings Comm Port COM n IRQ l
33. led an Advanced Power Management device will be activated to enhance the Max Power Saving mode and stop the CPU internal clock If Advance Power Management APM is installed on the system selecting Yes gives better power savings If the Max Power Saving is not enabled this will be preset to No 44 System Installation PANEL1125 675 User s Manual Video Off Option When enabled this feature allows the VGA adapter to operate in a power saving mode Monitor will remain on during power Always On saving modes Monitor blanked when the system enters Suspend gt Off the Suspend mode Monitor blanked when the system enters Monitor blanked when the system enters All Modes gt Off any power saving mode Video Off Method This determines the manner in which the monitor is blanked This causes the system to turn off the V HSYNC Blank vertical and horizontal synchronization ports and write blanks to the video buffer Select this option if your monitor supports the Display Power Management Signaling DPMS standard of the Video Electronics Standards to select video power ement values This option only writes blanks to the video Video Off Method In suspending this item is to select the CRT closed method under APM mode The choice Blank Screen V H SYNC Blank DPMS MODEM Use IRQ APM 1 2 function used only The choice NA 3 4 5 7 9 10 11 System Installation 45 PANEL 1125 675 Users Manual
34. m configuration Additionally when a password is enabled the BIOS can also set to request a password every time the system reboots This would prevent unauthorized use of the computer The user can determine when the password is required within the BIOS Features Setup Menu and its Security option If the Security option is set to System the password is required during boot up and entry into Setup If it set as Setup prompting will only occur prior to entering Setup 52 System Installation PANEL1125 675 User s Manual Appendix B Power Supply Specifications The power supply used in the PANEL1125 675 is a 100W open frame power supply The specifications and features of this special power supply are listed in the following sections B 1 AT 100W Power Supply This Power Supply is a triple output 110 watts power supply B 1 1 Output Specifications Load Range Output Voltage Accuracy A Total output power The max power is 130W that works with 18CFM air forced cooling Line regulation less than 0 5 Ripple and noise 1 pk pk max 1 2 Input Specifications Input voltage range 90 264 VAC Inrush current 30A at 115 VAC or 60A at 230VAC cold start Input frequency 47 63 Hz Power Supply Specifications 53 PANEL1125 675 Users Manual 1 3 General Specifications Efficiency 80 typ 1 4 Environmental Specifications Operating temperature range 0 C to 50 C Storage temperature range 40
35. ons 1 Remove the screws from back cover 2 Install CPU and SDRAM in the system 3 Secure the screws of back chassis DRAM Riser card 10 System Installation PANEL1125 675 Users Manual 2 2 HDD Installation When upgrading the 2 5 hard disk refer to the following steps 1 Find out 1 HDD bracket kit and 4 rubbers screws 2 Screw 4 anti vibration rubbers to the 2 5 hard disk System Installation 11 PANEL1125 675 Users Manual 3 Secure 4 screws in the bracket 4 Screw the HDD bracket in the PANEL1125 675 6 Connect the HDD cable 12 System Installation PANEL1125 675 User s Manual 2 3 Add on Card Installation The PANEL1 125 675 offers half size PCI ISA shared expansion slot This makes the PANEL1 125 675 flexible for versatile applications Before you install add on card in the slot please make sure that the dimension of the card is within 185x100mm 1 Remove the back chassis 2 Install the add on card in the slot e E 4 E cam gt 3 Secure the screws to fix the add on card System Installation 13 PANEL1125 675 Users Manual Note If you think that it s tight to plug ISA card in the slot you can refer to the following steps 4 Unscrew the screws in the ISA bus add on card 5 Install ISA card in the slot 14 System Installation PANEL1125 675 User s Manual 6 Secure the screws to fix the card 2 4 Serial Ports Setting The PANEL1125 6
36. otection ESD device option Touch activate indication LED on board System Installation 19 PANEL1125 675 Users Manual 3 2 Driver Installation Windows 98 NT 2000 XP Windows XP embedded The touch screen of PANEL1125 675 provides a driver for use with Windows 95 Windows 98 Windows NT 4 0 or Windows 2000 XP To facilitate installation of the touch screen driver you should read the instructions in this chapter carefully before you attempt installation 1 Insert Driver CD and select the D PANEL1125 675 Driver Touch screen Windows 9x or 2k or XP Setup exe Dos Driver LinuxXFree86 Linux XFree86 QNX62x Windows Windows 31 Windows95 Windows i VLOL i 336Dmver 4xxDriver Driver 2000 XPD Driver V1 0 Driver V2 1 98 MeDrv WindowsCE Windows NT Driver Driver 1 0 04 2 Follow the install procedure and press OK 3 Click Start menu and select PenMount Utilities You can see PenMount Control Panel Ey PenMount Control Panel Calibrate Draw Multiple Monitors Option About PenMount DMC3000 and DMC3100 Driver Version 4 01 Firmware Version E mail salt salt com tw Website www salt com tw Copyright C 2003 Salt Int l Corp 20 System Installation PANEL1125 675 User s Manual 4 Select the Standard Calibrate tab E PenMount Control Panel Calibrate Draw Multiple Monitors Option About Advanced Mode 9 Plot calibration data Advanced Calibration 5 Cal
37. rd disk will not work properly if the improper information within this category is entered If the disk drive type does not match or is not listed the Type User is used to define the drive type manually Ifthe Type User is selected related informationhas to be entered Enter the information directly from the keyboard and press Enter This information should be provided in the documentation fromthe hard disk vendor or the system manufacturer If the controller of HDD interface is ESDI select Type 1 If the controller of HDD interface is SCSI select None If the controller of HDD interface is CD ROM select None number of number of number of P HDD access PRECOMP write precom MODE If there is no hard disk drive installed select NONE and press Enter 28 System Installation PANEL1125 675 User s Manual Drive A type Drive B type The category identifies the types of floppy disk drive A or drive B installed in the computer None No floppy drive installed 360K 525in 5 25 inch PC type standard drive 360Kb capacity 5 25 inch AT type high density drive 12M 3 2310 1 2MB capacity capacity 3 5 inch double sided drive 1 44MB AAS 3 5 inch double sided drive 2 88MB capacity 2 88M 3 5in 720K 35 in 3 5 inch double sided drive 720Kb Select Display Device This item selection includes Auto CRT LCD and CRT LCD LCD Type This item selection includes TO 640x480 TFT T1 800x600 TFT T21024x7
38. re monitoring IC 2 5V 3 3V 5V 12V Show the voltage of 2 5V 3 3V 5V 12V System Installation 49 PANEL1125 675 Users Manual A 8 Frequency Voltage Control CMOS Setup Utility Copyright 1984 2001 Award Software Frequency Voltage Control Auto Detect DIMM PCI Clk Enabled Spread Spectrum Disabled Menu Level gt CPU Host PCI Clock Default VY Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Auto Detect DIMM PCI Clk When enabled this item will auto detect if the DIMM and PCI socket have devices and will send clock signal to DIMM and PCI devices When disabled it will send the clock signal to all DIMM and PCI socket The choice Enabled Disabled Spread Spectrum This itemis to enable disable the spread spectrum modulates The choice Enabled Disabled 50 System Installation PANEL1125 675 User s Manual A 9 Load Fail Safe Defaults This option is to load the troubleshooting default values permanently stored in the BIOS ROM These default settings are non optimal and disable all high performance features Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Frequency Voltage Control Advanced BIOS Features Load Fail Safe Defaults Advanced Chipset Features Load Optimized Defaults Integrated Peripherals Set Supervisor Password Power Ma Load Fail Safe Defaults Y N N PnP PCI C PC Health Status
39. sed in the PANEL1125 675 is SBC83675 The different settings are available in the Award BIOS that comes with the SBC83675 Also contained here are instructions on how to set up the BIOS configuration A 1 Standard CMOS Setup Standard CMOS Setup is used to record some basic hardware configurations in the computer system and set the system clock and error handling If the motherboard is already installed in a working System there is no need to enter this option However the Standard CMOS option has to be setup in any of the following situations the system hardware configurations are changed the onboard battery fails and the configuration stored in the CMOS memory is lost or damaged Phoenix AwardBIOS CMOS Setup Utility Standard CMOS Features Date mm dd yy Wed ME 7 2002 Item Help Time hh mm ss 13 29 11 Menu Level gt IDE Primary Master None IDE Primary Slave None Change the IDE Secondary Master None Day month IDE Secondary Slave None Year and Century Drive A 1 44M 3 5 in LCD Type T9 800x600 TFT Screen Expansion Enable TV Type NTSC Display Type During Post VGA Default Display Type After Post VGA Default Halt on All But keyboard Base Memory 640K Extended Memory 65535K NV gt lt Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults 26 System Installation PANEL1125 675 User s Manual At the bottom of the menu
40. slots for users the PANEL1125 675 also provides 1 PCI ISA expansion slots for add on cards extended The build in 8 channels DIO controller allows users to connect simple digital measurement and control the PANEL1125 675 without adding a DIO card to the system This ideal industiial grade panel computer PANEL1125 675 can be applied to the several of industrial or commercial projects such as transportation factory automation HMI machine controller Point Of Sales KIOSK and more Moreover PANEL1125 675 provides highly reliable and highly flexible industrial grade products in all in one solutions Introduction 1 PANEL1125 675 User s Manual 1 1 Features 12 1 TFT 350 nits high brightness SVGA LCD Aluminum front bezel and chassis 2 5 HDD CompactFlash Card or DiskOnChip supported 1 PCI ISA extension slot 8 TTL digital input output Supports various mounting ways Desktop Panel Wall VESA ARM Supports AC DC24V 48V power supply Windows 98 NT 2000 XP Linux O S supported Windows CE NET Windows XP Embedded supported 1 2 Specifications 1 2 1 Main CPU board CPU Intel Celeron 533MHz 1 3G MHz Intel Pentium Ill 550 1 4G MHz VIA Cyrix 111 C36 Family at 100 133MHz FSB System Chipset VIA VT8606 Twist T VT82C686B BI OS Phoenix Award BIOS 4Mbit with RPL PXE LAN boot ROM SmartView and customer BIOS backup System Memory One 168 pin DIMM Socket Maximum of 512MB SDRAM ECC parity L2
41. t PASSWORD SETTING at Main Menu and then password is asked to enter Do not type anything just press Enter and it will disable security Once the security is disabled the system will boot and you can enter Setup freely OS Select for DRAM 64MB This segment is specifically created for OS 2 when DRAM is larger than 64MB If the operating system is OS 2 and DRAM used is larger the 64MB OS 2 has to be selected otherwise under non OS2 default is NON OS2 Video BI OS Shadow Video shadowing increases the video speed by copying the video BIOS into RAM However it is still optional depending on the chipset design The default value of this option is Enabled Enabled Video BIOS shadowing is enabled Disabled Video BIOS shadowing is disabled C8000 CBFFF Shadow DCOO0 DFFFF Shadow Shadowing ROM reduces available memory between 640KB and 1024KB These fields determine whether optional ROM is copied to RAM or not System Installation 35 PANEL 1125 675 Users Manual A 3 Advanced Chipset Features Since the features in this section are related to the chipset on the CPU board and are completely optimized changing the default settings in this setup table are not recommended unless the user is well oriented with the chipset features Phoenix AwardBIOS CMOS Setup Utility Advanced Chipset Features DRAM Timing By SPD Enabled Item Help X DRAM Clock Host CLK X SDRAM Cycle Length 3 Menu Level gt X Bank Interlea
42. t n gt 1 PMDETECT program is able to skip the IRQ number detecting if you Touchscreen Driver Installation 13 do not need to detect the specified IRQ number For example you do not need to detect IRQ5 and the command is C PENMOUNT PMDETECT N5 22 System Installation PANEL1125 675 Users Manual If you do not need to detect IRQ5 and IRQ9 the command is C PENMOUNT PMDETECT N5 N9 3 3 3 Do Calibration 1 To adjust the touch screen mapping properly to display screen use PM BAT CAPENMOUNTVPM to do calibration Choose 1 DO CALIBRATION adjust screen mapping 2 The message on screen asks you to select video mode number Select by keyboard to start the calibration touch the upper center point then right center point bottom center point and left center point in sequence After calibration the data is shown in the screen press any key to continue the progress 3 After the calibration suggest you to test touch screen and display mapped results by choose 3 DRAWING TEST under PM BAT 3 3 4 Initializing the PenMount driver If you don t have the initialization commands in AUTOEXEC BAT initialize PenMount C PENMOUNT PMINIT controller before you use the PenMount Touch Screen The display will show the initialization message PenMount V7 06 Copyright c SALT International Corp Test COM lt n gt IRQ lt n gt lt n gt is the number after PHDETECT done PenMount communication settings COM lt N gt IRQ lt
43. ve Disabled Memory Hole Disabled P2C C2P Concurrency Enabled System BIOS Cacheable Disabled Video RAM Cacheable Disabled Frame Buffer Size 16M AGP Aperture Size 64M AGP 4X Mode Enabled AGP Driving Control Auto AGP Driving Value DA OnChip USB Enabled USB Keyboard Support Disabled OnChip Sound Auto OnChip Modem Disabled CPU to PCI Write Buffer Enabled PCI Dynamic Bursting Enabled PCI Master 0 WS Write Enabled PCI Delay Transaction Disabled PCI 2 Access 1 Retry Enabled AGP Master 1 WS Write Disabled AGP Master 1 WS Read Disabled VY Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults 36 System Installation PANEL1125 675 User s Manual DRAM Timing By SPD This itemis selected depending on whether the board has paged DRAMs or EDO extended data output DRAMs DRAM Clock The DRAM clock value is set depending on whether the board has paged DRAMs or EDO extended data output DRAMs The available choices are 66 MHz and Host CLK SDRAM Cycle Length When synchronous DRAM is installed the number of clock cycles of CAS latency depends on the DRAM timing Do not reset this field from the default value specified by the system designer The default setting is 3 Memory Hole To improve performance certain space in memory is reserved for ISA cards This memory must be mapped into the memory space below 16MB The available c
Download Pdf Manuals
Related Search