INSTALLATION MANUAL
Contents
1. 8 tally outputs corresponding to the video sources one to eight The system also has 5 GPI inputs These can be configured to trigger the AutoTrans Cut Fade to Black transitions and or Timeline functions Electrical Specification The GPI port is a 15 way Male Connector as shown right Pins 1 to 8 correspond to Tally outputs 1 to 8 Pins 9 to 13 correspond to General Purpose Inputs 1 to 5 Pins 14 amp 15 are Signal Ground pins view looking at rear panel GPIs All of the input lines are Active Low and are internally pulled up to 5V via 1K2 resistors GPI inputs are level triggered and are sampled once per field Tallv Outputs Tallv outputs are Active High TTL signals These are permanentiv enabled and require no software setup The state of the tallv outputs follow the program output bus as follows Active Button Tallv output PA WARNING THE TALLY AND GPI INTERFACE IS CONNECTED TO THE PROCESSOR CIRCUITRY DAMAGE TO THE PROCESSOR MAY BE CAUSED IF ADEQUATE PRECAUTIONS ARE NOT TAKEN S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 5 ESE JO CONTROL CABLE WIRING SwitchPack 16 Mainframe to Control Panel or Editor Panel or Editor Mainframe Male 9 Way Female 9 Way D type D type N C 1 1 Tx Rx 2 2 Tx Tx 3 3 Rx Gnd 4 4 Rx N C 5 5 Gnd Gnd 6 6 N C Rx 7 7 N C Tx 8 8 N C N C 9 9 N C 6 SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Pr2. cables such as Belden 8281 or BBC type PSF1 2M D TYPE CONNECTORS D type connectors shall have metal shells making good RF contact with the cable screen Connectors having dimples which improve the contact between the plug and socket shells are recommended vi SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Production Post Production ESE CONTENTS Port Descriptions External Reference Sync Updating Software and Hardware System Info Menu Disk Update Method Editor and Panel Cable Edit r Wipe G608S C ee S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 vii ESE JO DELIBERATELY BLANK viii SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Production Post Production SNe amp wicox JO Unpacking Check the delivery against the shipping note to ensure that all items are present Unpack the equipment carefully and check all items for transportation damage If damage has occurred contact the shipping company and Snell amp Wilcox Ltd or the local agent immediately with a written description of the visible damage The SwitchPack 16 system comes in two boxes one for the Control panel and the other for the Switcher Mainframe The Control Panel box contains Control panel and RS422 Serial Comms cable The Mainframe box contains Mainfr
3. INSTALLATION MANUAL SNELL amp wiLcox JO ESE SwitchPack 16 Installation Manual Issue 1 Revision 1 March 2003 2003 Snell amp Wilcox Post Production Division The Business and Technology Centre Shire Hill SAFFRON WALDEN Essex CB11 3AQ U K Tel 44 0 1799 523817 Fax 44 0 1799 528081 Support Tel 44 0 1799 508100 Support Fax 44 0 1799 508800 Support E mail post support snellwilcox com Web http www snellwilcox com COPVRIGHT Copvright protection claimed includes all forms and matters of copvrightable material and information now allowed by statutory or judicial law or hereinafter granted including without limitation material generated from the software programs which are displayed on the screen such as icons screen display looks etc Information in this manual and software are subject to change without notice and does not represent a commitment on the part of Snell amp Wilcox Ltd The software described in this manual is furnished under a license agreement and may not be reproduced or copied in any manner without prior agreement with Snell amp Wilcox Ltd or their authorised agents Reproduction or disassembly of embedded computer programs or algorithms prohibited No part of this publication may be transmitted or reproduced in any form or by any means electronic or mechanical including photocopy recording or any information storage and retrieval system without permission be
4. ainframe Rear View Z PNO GAS AGA A MA A SINS S 2 1 o o lt Q O o Q O Q Q O O ge E NET Aj ete reg JO e E KO NE Q Q f 00000688 20005 EP d E BYP GM PST Meini una Port Descriptions Black Burst with 300mV Sync loop BNC BYP Outputs program or input 8 on power fail Serial BNC External Reference Synchronisation The SwitchPack 16 MUST be locked to an external analogue reference source usually black burst with 300mV sync The unit auto senses 525 625 signals Note The SwitchPack 16 Engineering System menu must be set to AUTO for auto sense to be enabled 2 SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Production Post Production sneu amp wucox JO UPDATING SOFTWARE AND HARDWARE System Info Menu Information about the options installed the software build date and the hardware build dates can be accessed from the System Info Menu This menu is hidden from normal use To access it you must press the top three menu buttons simultaneously KEY WIPE 1 WIPE 2 SD S amp W System Info S W Build 03 Mar 2003 Panel Ver 2 0 Serial No 00 00 00 Versn H W Optns Figure 1 Svstem Info Menu The Svstem Info Menu has three sub menus which can be accessed using the bottom three softkeys Versn H W and Optns The Versn menu above displays the mainframe software build date the panel vers
5. ame and the Manuals The Mainframe The SwitchPack 16 mainframe is designed for mounting in a 19 equipment rack It occupies 1 Unit of rack space vertically and 21 535mm of rack depth The mainframe is supplied fitted with two rack mounting ears These ears are screwed to each side at the front of the mainframe using six Screws three each side The mainframe should be mounted in a standard 19 rack equipped with a rack tray to support the weight of the mainframe using the front ears merely to position it The ears should not be used to support the unit The Mainframe is cooled by four fans along one side of the unit These fans draw air in through vents in the opposite side and the front of the unit providing a cross flow Do not obstruct the inlet vents or the fans There is no mains power switch on the mainframe To the left front of the mainframe is a standard 1 44MB Floppy disc drive for archiving of all files At the rear of the mainframe the mains inlet video reference and the control ports are found The external connections are all clearly marked See diagram of rear panel on page 2 The Control Panel The Control Panel is powered from an internal power supply unit Communication to the Mainframe is via a RS422 link using 9 pin D Type connectors Control Panel operations are described in the user manual S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 1 ESE M
6. h have an internal power supply Mains Supply Voltage Before connecting the equipment observe the safety warnings section and ensure that the local mains supply is within the rating stated on the rear of the equipment Supply voltages for both units must be in the range 100 vac to 120 vac or 200 vac to 240vac at 50 to 60Hz Model Number PSU Rating Fuse Rating 100 120V Control Panel 4038200 200 240V T1AH 1A Max 100 120V Mainframe 4038550 200 240V T2AH 1 75A Max S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 iii SNe amp wicox JO Power cable supplied for the USA The equipment is shipped with a power cord with a standard IEC moulded free socket on one end and a standard 3 pin plug on the other If you are required to remove the moulded mains supply plug dispose of the plug immediately in a safe manner The colour code for the lead is as follows GREEN lead connected to E Protective Earth Conductor WHITE lead connected to N Neutral Conductor BLACK lead connected to L Free c go Free Live Conductor Plug Socket Power cable supplied for countries other than the USA The equipment is shipped with a power cable with a standard IEC moulded free socket on one end and a standard IEC moulded plug on the other If you are required to remove the moulded mains supply plug dispose of the plug immediately in a safe manner The colo
7. ing granted in writing by the publishers or their authorised agents Specification subject to change without notice All Trademarks acknowledged ii SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Production Post Production SNe amp wucox JO SAFETY This symbol refers the user to important information contained in the accompanying literature Refer to users manual This symbol indicates that hazardous voltages are present inside There are no user serviceable parts inside This unit should only be serviced by trained personnel A AX Servicing instructions where given are for use by qualified personnel only To reduce risk of electric shock do not perform any actions on this equipment other than contained in the operating instructions unless you are qualified to do so Refer all servicing to qualified personnel WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE Always ensure that the unit is properly earthed and power connections correctly made This equipment must be supplied from a power system providing a PROTECTIVE EARTH connection and having a neutral connection which can be reliably identified The control panel shall be separately earthed via the terminal on the rear of its enclosure The power outlet supplying power to the unit should be close to the unit and easily accessible Power Supply and Connections The mainframe and the control panel eac
8. ion and the serial number H W Shows the build date of the hardware system files Optns Shows the currently active options These will be either Active or Off The line Sys Expires Shows the expiry of the main system If the system expires then the unit will cease to function Never means that the system will never expire EXPIRED 1 means that the system has expired Contact Snell amp Wilcox for an updated Password Disk If this line shows a date then the system will expire on that date S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 SNe amp wucox JO Disk Update Method Software password and hardware updates are mainly provided in the form of one or more floppy disks The installation procedure is automated and is carried out as follows Power down the mainframe Put the disk in the floppy drive and power up the system The machine will now reboot and copy the contents of the floppy disk onto the system hard drive The panel will also update to show each file being copied When the installation is complete Remove the disk from the floppy drive and cycle the power on the mainframe The system will now operate as normal again 4 SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Production Post Production ESE TALLY amp GPI INTERFACE SwitchPack 16 has a simple tally and GPI interface using basic TTL levels Tally amp GPIs SwitchPack 16 has
9. oduction Post Production SNe amp wicox JO EDITOR WIPE CODES The following charts describes the wipe codes needed by an editor driving a SwitchPack 16 switcher Wipes codes are dependent on the editor protocols selected GVG200 Protocol Wipe Codes 200 Wipe Code Function Vertical Wipe Top Left Corner Wipe Clock Wipe Clock Wipe Top Right Corner Wipe Left V Wipe 13 Ellipse Wipe Diagonal Top Left Wipe 17 45 Cross Wipe 23 Square Wipe 30 Horizontal Mirror Wipe 4 Diamond Wipe Egg Timer Wipe S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 ESE JO END OF MANUAL S amp W Production Post Production
10. uct family standard for audio video audio visual and entertainment lighting control apparatus for professional use Part 1 Emission BS EN 55103 2 1997 Electromagnetic Compatibility Product family standard for audio video audio visual and entertainment lighting control apparatus for professional use Part 2 Immunity Federal Communications Commission Rules Part 15 Class A 1998 EMC Environment The product s described in this manual conform to the EMC reguirements for and are intended for use in either The commercial and light industrial environment including for example theatres E2 or The controlled EMC environment e g purpose built broadcasting or recording studios and the rural outdoor environment far away from railways transmitters overhead power lines etc E4 EMC Performance of Cables and Connectors Snell amp Wilcox products are designed to meet or exceed the requirements of the appropriate European EMC standards In order to achieve this performance in real installations it is essential to use cables and connectors with good EMC characteristics All signal connections including remote control connections shall be made with screened cables terminated in connectors having a metal shell The cable screen shall have a large area contact with the metal shell COAXIAL CABLES Coaxial cables connections particularly serial digital video connections shall be made with high quality double screened coaxial
11. ur code for the lead is as follows GREEN YELLOW lead connected to E Protective Earth Conductor BLUE lead connected to N Neutral Conductor BROWN lead connected to L Live Conductor Free Plug Free Socket iv SwitchPack 16 Installation Manual Issue 1 Rev 1 S amp W Production Post Production SNe amp wicox JO Maintenance amp Repair There are no user serviceable parts within either the Mainframe or the Control Panel In the unlikely event of an equipment failure contact the Snell amp Wilcox Post Production Customer Support department contact details below Telephone 44 0 1799 508100 Fax 44 0 1799 508800 e mail post support snellwilcox com Cooling Fan Failure IF A COOLING FAN IN THE MAINFRAME SHOULD STOP FOR ANY REASON THE SYSTEM SHOULD BE SWITCHED OFF IMMEDIATELY OR PERMANENT DAMAGE MAY RESULT Depending on the length of time the mainframe has been run with no fan the unit may need to be returned for checking and repair Contact Snell and Wilcox or your Snell and Wilcox dealer to discuss the situation Safety Standards This equipment complies with the following standards BS EN60950 2000 Safety of information Technology Equipment Including Electrical Business Equipment S amp W Production Post Production SwitchPack 16 Installation Manual Issue 1 Rev 1 v AKM EMC Standards This unit conforms to the following standards BS EN 55103 1 1997 Electromagnetic Compatibility Prod
Download Pdf Manuals
Related Search