User Manual
Contents
1. Standard UL 4 2XSL1210 shown The SmartPack Touring system offers small compact design built to travel Standard UL Touring rack provides room for two or four SmartPack dimmer packs with the similar output panel options as available in the SmartPack 19 Portable pack The UL SmartPack Touring system is SmartLink enabled and includes built in mains distribution with options for a main circuit breaker or a Cam Lok pass thru panel Standard CE Touring racks are available in a road case with any two SmartPack dimmer packs of your choice with similar output panel options as available with the CE SmartPack 19 Portable pack The CE SmartPack Touring system is SmartLink enabled and includes circuit breaker power distribution per pack with options for a mains breaker and RCD protection and a convenience outlet for accessories All the standard features of the SmartPack Portable unit in an industrial grade road case Contact ETC for configuration details Standby Control Power Switch Chapter 1 Menus and Configuration User Interface The SmartPack family user interface and menu structure provide users an intuitive easy setup with multiple language options built in Control Power2. Miti Part Number Breaker Voltage Supply SL620W 7021A1100 SL620W LPS 7021A1100 LPS with LinkPower Supply SL1210W 7021A1101 SL1210W LPS 7021A1101 LPS with LinkPower Supply SL1210TPW 7021A1102 with ThruPower only t us LISTED Part Number Channels Breaker Voltage Supply C 7021A1103 12 10A 7021A1103 LPS 12 10A with LinkPower supply 7021A1105 12 10A ND with 2 pole breakers 7021A1105 LPS 12 10A ND with 2 pole breakers and LinkPower supply 7021A1106 6 15A 7021A1106 LPS 6 15A with LinkPower supply 7021A1107 6 15A ND with 2 pole breakers 7021A1107 LPS 6 15A ND 230V 47 63Hz with 2 pole breakers and LinkPower supply 7021A1110 3 25A ND 39 or 10 with 2 pole breakers 7021A1110 LPS 3 25A ND with 2 pole breakers and LinkPower supply 7021A1111 12 10A ThruPower Switch 7021A1112 12 10A ND ThruPower Switch 7021A1113 12 10A ThruPower Relay 7021A1114 12 10A ND ThruPower Relay 7021A1115 12 10A Relay only 7021A1116 12 10A ND Relay only b Overview SmartPack 19 Portable The SmartPack Portable dimmer packs are designed in a rugged 19 inch 2 space rack mount package Ships standard with SmartLink enabled for total versatility e ULlisted SmartPack Portable dimming packs are available with either six 20A dimmers or twelve 10A dimmers CE marked Smart
3. ETC recommends configuring the SmartPack with the LinkPower supply installed and wall stations connected as the Station Master For systems without wall stations there is no requirement to configure a station master Default functionality for pack to pack synchronization is that the last SmartPack or SmartSwitch updated in the system acts as the station master and send its host messages to the other products in the system Step 1 Step 2 Scroll to Stations and press 2 Scroll to Station Master and press y If the SmartPack you are configuring is to be the Station Master scroll to Enable and press 2 If the SmartPack you are configuring is not the Station Master scroll to Disable and press y Remote Record Enable Remote Record within the station master for user ability to record presets from SmartLink wall stations Disable Remote Record within the station master to lock out the ability to record presets from SmartLink wall stations Step 1 Step 2 Step 3 Step 4 From the face panel of the station master scroll to Stations press y Scroll to Remote Record press 2 For the ability to record a preset from a SmartLink wall station scroll to Enable and press v After enabling Remote Record the user has the option to set dimmer levels to a desired look via the test menu or other DMX control device and record that look to a specific preset via the wall station
4. dois Joouenbe yes Jeouenbe suoneis ew edyeu seA1n9 Jewwiq H u nb sl SmartPack User Manual 28 nuayy peoueApy nuaw jeuuoN epon nuan sG6umes sG6umes elouag HHH CA uors1aA aemyos sBumes U0ISI9A sG6umes e aua 3oegueus 913 LARA XING sseuppy XWA Xwa XWA yoedquews 213 01 1 nus BWJON OHH ZH sonsouBeig MO I MO Z130 11 xoegueuis 313 snoad EULON HolApu g dn Jemod s um s eJaua yo je se 195 9 uo 3s l deey 1S9 1 1X3 5 AHHH 19 97 YO HE 6 auemyos JOWWIC 3S9 L sBunjas jeJeuec waj s s Jea 9 dee poyy 1891 3X8 1821 pue xg s um s Touuey u ur roul qovucu juouro10o q synejeq o jasay 1 i sG6umes eJauas 1uouro1ou suonoun4 uoyng peoueApy nus 1891 jguuoN nuan epoN NUIN sBunjas pueds3 yos neq ebenbue7 jas steoue 4 ysi Buz hu6rppeg 4211 oBenDue11e eBenBue4 19 1y6ppeg 4211 sbunmosg esaua eDenBue pekejdsip eui jes 0 joajas sjenejul puooes ouedsa Je suondo ay UGnouy seoiouo eDenDue1 2 uosineq L sreoues 4 e6enbue7 198 sBunjas je1eues ysy6ua sbumes yoeduews 913 edsa 01 JemOg SUN 1811
5. Step 4 Reinstall front cover before applying power to the unit Ensure that the ground wire is reattached to the front cover Replacement Parts Two different fuses are used in three places on the SmartPack control board Field replacements are available by ETC or may be purchased at your local electrical supply house e Control board location F1 and F2 use fuse type 0 125A 250V F 5x20mm ETC part number F113 F Control board location F3 use fuse type 0 500A 250V F 5x20mm ETC part number F112 F All other field issues please contact ETC technical services for assistance 24 SmartPack User Manual Appendix A LinkPower Supply Kit One SmartLink LinkPower Supply S LPS powers up to four wall stations over the SmartLink network You may have only one station power source on the SmartLink network This source may be either the LinkPower Supply S LPS or a SmartLink Station Power Module S SPM which powers up to 16 SmartLink stations As well you may have up to four SmartLink host products in a SmartLink system One SmartLink host product SmartPack SmartSwitch Unison DRd with SmartLink or Sensor with SmartLink in the system must have a LinkPower Supply or Station Power Module installed for wall station power Due to the similar design for the SmartPack Wall Mount and the SmartSwitch Relay Panel control terminations the following instructions may be used for either product Installation P
6. 10 ts do Roky A a E q 10 Presets 2 ithe Rls a ie Ee 11 ease 12 CUI DTE 13 EMENGENCY iss ll vl kle ee ee ee 14 Stations U Aaz ti ad AE os o x Ba Mf JA oi aba 14 General Settings ii lin ll va nu ke an aa an na ae ank 16 Diagnostics dik 17 Chapter 2 SmartLink Enabled 18 Features usps tuii as all ea a a A ANS UU RI ei d 18 Definitions eun cut Weed canes TE a acetal as ee A A ie 19 Pack SynchroniZatiON see ese eee never nee 22 20 Table of Contents i Preset and Sequence Synchronization 20 SALONS Git and kari ate tux ts ied s ute d cei AD 21 Record a Preset from a Wall Station 22 Chapter 3 Service and Maintenance 23 SEVICE xn m aaa ts ete Rc eee 23 Contacting ETC about Equipment Problems 23 Maintenance 2S rada ara ri AA doe te ed 24 Vac m the Ventnor arra Revue 24 Vacuum the nterior 24 Replacement Parts 24 Appendix A LinkPower Supply Kit 25 Installation Procedure 25 Appendix B Menu Flow Chart 27 ii SmartPack User Manual Introduction Congratulations on your purchase of the ETC SmartPack dimmer pack SmartPack continue
7. DMX Start Address set to start address gt 1 3 1 6 or 1 12 lt DMX Loss Behavior resets to gt Hold Last Look lt Deep Clear System Resets the unit as if it were new out of the box including the following attributes Resets same defaults as indicated in Reset to Defaults Clears presets and preset timing values to default values e Resets Language and prompts the user for language selection Software Version Displays current software version 16 SmartPack User Manual Power Up Behavior Choose between Normal or Previous State Normal the SmartPack powers up with both presets and the sequencer de activated Previous State powers up the SmartPack with the preset or the sequence active that was running during the previous session This feature allows unattended operation through power blackouts This state will not restore Test levels Diagnostics The diagnostics menu provides feedback of line errors and temperature readings for each line The initial display shows the temperature reading in C press the button for F readings at Menus and Configuration 17 Chapter 2 SmartLink Enabled Features SmartLink is a communications network created for enhanced control of the 32 built in presets and sequence as found in SmartLink enabled products The addition of the SmartLink network facilitates two additional control features wall stations and pack to pack synchronization Neither control feature is
8. User Manual Version 2 1 Copyright Electronic Theatre Controls Inc All Rights reserved Product information and specifications subject to change Part Number 7020M1200 2 1 0 Rev B Released 2014 02 ETC SmartPack SmartSwitch and SmartLink are either registered trademarks or trademarks of Electronic Theatre Controls Inc in the United States and other countries All other trademarks both marked and not marked are the property of their respective owners Table of Contents ntroduction 1 Congratulations lille ee 1 Using this Manual 1 OVEPMHe n doit it eat ta 2 Standard Features ius duro bare one QUERI aa boats 2 SmartPack Wall Mount 3 SmartPack 19 Portable 4 SmartPack Touring System 5 Chapter 1 Menus and Configuration 6 Userinterface Lue a pan an 6 Control Power Switch and LED Indicators 6 Keypads cid he ee da 6 TEC Dif artes Thos NU 7 Initial Power Up Display 7 Men Eockout RII Sec ede e EA 7 Circuit Mode Selection Switches for SmartPacks with ThruPower 8 Normal Menu Structure 9 Normal Menu Le Ri RIA e Gr 9 EE 9 Advanced Menu Structure
9. Test all offf displays To exit the Test menu and retain all Test Levels Scroll to Keep test on and press v Exit Test menu clearing all Test Levels and return to the previous menu Scroll to Test all off and press w Press to return to the main menu and clear all Test Level Lil Menus and Configuration Advanced Menu Structure DMX Enter the Advanced menu from the Normal Menu The Advanced menu provides all access to the menu and configuration settings for the SmartPack Step 1 Scroll to General Settings press y Step 2 Scroll to Menu Mode press y Step 3 Scroll to Advanced Menu press and hold y for 5 seconds The display will return to the main menu when the Advanced Menu has been accessed Ifthe y is released prematurely the menu will remain in Normal Menu mode DMX Start Address The start address range is determined by the size of your SmartPack When a DMX Start Address is selected as the active DMX Mode the DMX range will be displayed on the LCD DMX 001 gt 012 aM Level DMX Start Address range Athree channel unit allows a start address range of 001 510 A six channel unit allows a start address range of 001 507 Atwelve channel unit allows a start address range of 001 501 Step 1 Scroll to DMX press v Step 2 Scroll to DMX Start Address press y Step 3 Use or to increment or decrement the Start Address range Press y to set the address and return to t
10. sseuppy ueis XNA gt yo ed XING spow XNA no epey pue ye M XWa ape XWA 4007 1SE77 pioH Xna HHH XING lt wid uoied XING l lt HHETXING SsoJppy HEIS 195 Buiu dmes p102e3 SjeseJg eyeAnoeeg HH S S ld h s d Hi S S Lci esuodsay xwa opon Xna Xna HolAsu g sso7 XWa XING 49ed XNA sseuppy Hes XNA XWA 27 Menu Flow Chart moy90 nueui obeBuesip o spuooes G 101 pue pue ssaJd 4 ADO INN YALNA GH3201 STOM LNO BojJeip noy90 e elds p ym pun ay possoud si eoepiejui Jesn eu uo uojinq e pue s mnoy90 uauM 1noyoo nuau o spuooes G 10 pue pue SS ld l lqesiq lqeuzil jn0y201 huey JO oN seA AoueBJeuu3 l 96341 jueosaJon y husosouonj4 DENOA uelis 18S uunu JOWUWIG JeoH 81d he H zcil 9A97 Bd 18S uinu JOWWIG eouenbes ss ww ope4y deis 9Any eouenbegs ou Jo se doo1 oeouenbes dnje sdajs jo jequunN gouanbas dnje paddo s souanbas p1099y ojousy H ululq ubissy KoueBueui jueoseJon 4 pouyojims e9H 91d Jeou me SJENDS SeAIno Me T1 YOS POW lt 4 uunu jewwiqg sme Jeouenbes Jaguenba eouanbas dm sl Jaguenba
11. 29 Menu Flow Chart e Corporate Headquarters m 3031 Pleasant View Road P O Box 620979 Middleton Wisconsin 53562 0979 USA a Tel 608 831 4116 Fax 608 836 1736 London UK w Unit 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK w Tel 44 0 20 8896 1000 m Fax 44 0 20 8896 2000 Rome T a Via Pieve Torina 48 00156 Rome Italy Tel 39 06 32 111 683 a Fax 39 06 32 656 990 Holzkirchen DE m Ohmstrasse 3 83607 Holzkirchen Germany a Tel 49 80 24 47 00 0 m Fax 49 80 24 47 00 3 00 Hong Kong Room 1801 18 F Tower Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong a Tel 852 2799 1220 m Fax 852 2799 9325 Service Americas service etcconnect com m UK service etceurope com m DE techserv hoki etcconnect com a Asia service etcasia com Web www etcconnect com m Copyright 2014 ETC All Rights Reserved m Product information and specifications subject to change 7020M1200 2 1 0 m Rev B m Released 2014 02
12. Scroll to select Yes to continuously loop the sequence or No to play the sequence only once and then stop Press 2 SmartPack User Manual Start Stop a Sequence Step 1 Scroll to Sequencer press 2 Start the sequence scroll to Start Sequence and press v Sequence Started will briefly display and the control symbol on the LCD will display the S Note The sequence will start at preset 1 and run for a user configured number of steps If the sequence is not configured to loop the sequence will stop If the sequence is set to loop the sequence will continue looping until the sequence is deactivated Stop the sequence scroll to Stop Sequence and press v Sequence Stopped with briefly display and the control symbol on the LCD will no longer display the S Curves SmartPack is capable of dimming or switching multiple load types including incandescent low voltage and 2 wire fluorescent SmartPack provides five user selectable dimmer output curves to choose IES modified square law Linear e Switched 50 threshold non regulated Fluorescent with adjustable cut off e Adjustable pre heat Set Dimmer Curve Step 1 Scroll to Dimmer Curves press 2 Step 2 Use or to select the specific dimmer number or ALL to be modified Press y Step 3 Use or to scroll through the five options press to select the output curve of choice a If Fluorescent output curve is selected you must specify
13. See Record a Preset from a Wall Station on page 22 If the ability to record a preset from a wall station is not desired scroll to Disable and press y If disabled preset recording must be accomplished from the face panel of the station master See Presets on page 11 Et Menus and Configuration 15 General Settings The General Settings menu is used to configure standard features of your SmartPack dimmer pack including Set Language Multiple language options to choose from English Francais e Deutsch e Espanol LCD BackLight User selectable LCD backLight performance Auto LCD dims when not in use for period of time On always on Off always off Menu Mode User selectable Normal Menu or Advanced Menu Normal limited menu options allowing users only to change the DMX Start Address from the DMX menu view the Software Version and change menu mode from the General Settings menu To enter Normal mode from the Advanced menu scroll to Normal and press w The SmartPack will request confirmation that you want to exit the Advanced menu scroll to Yes and press 2 Advanced all menu access To enter Advanced mode from the Normal menu scroll to Advanced and press and hold y for 5 seconds The menu will adjust back to the main menu automatically without further prompt Reset To Defaults Resets the following attributes to default status Dimmer Curves set to Mod SQR Law lt
14. the Start Voltage Fluorescent circuits provide a dimmable output in the 596 to 10096 control range Trim the minimum RMS output voltage to match your specific ballast The default voltage is 47 of your mains voltage Use or to increase or decrease the Start Voltage value Consult the ballast manufacturer s documentation for the appropriate minimum start voltage b If Preheat output curve us selected you must specify the preheat level allowable 096 2096 range Lil Menus and Configuration 13 Emergency SmartPack is provided with a emergency contact input When an active emergency contact is received all non emergency dimmers in the SmartPack are forced off while all user selected emergency dimmers energize to full During an emergency the LCD will display a message advising the Emergency Input Is Active and the menu will lock out all ability to access the system After normal power is restored the SmartPack will restore to the configured DMX Loss Behavior mode See DMX Loss Behavior on page 11 Assign Dimmers as Emergency Loads Step 1 Scroll to Emergency press 2 Step 2 Scroll to Assign Dimmer press y Step 3 Use or to scroll the dimmer list Press v to select a dimmer Step 4 Use or to scroll In Emergency Yes or No press 2 Step 5 Press lt to return to the previous menu or lt lt to return to the main menu Stations A SmartPack dimming pack with a SmartLink LinkPowe
15. Pack Portable dimming packs are available with either three 25A dimmers six 15A dimmers or twelve 10A dimmers In addition the SmartPack 19 Portable pack is available with a wide variety of output panel options to fit industry needs 6 Channel 12 Channel 3 Channel 6 Channel 12 Channel Stage Pin Stage Pin Multi pin NF French Harting Multipin Twist Lock PowerCon Terminal Output Swiss Socapex Multipin Japanese Twist Lock Dual 6 circuit CEE 32A 230V UK 15A Roundpin Terminal Output Multipin PowerCon Terminal Strip Power Con Single 6 circuit Wireland GST18 Multipin Terminal Strip Harting Socapex Part Number Channels Breaker Voltage Supply t US qd 7020A1000 with output panel and SmartLink 120 240 VAC 1Phase enabled SL1210 7020A1001 120 208 VAC 3Phase with output panel and SmartLink enabled P Breaker C art Number Type Voltage Supply SL325 ND 7021 1106 vvith 2 pole breakers and output panel SL615 7020A1002 xx vvith output panel and SmartLink enabled SL615 ND 7020 1004 230 240 VAC 47 63Hz with 2 pole breakers output panel and SmartLink enabled SL1210 7020A1003 xx with output panel and SmartLink enabled SL1210 ND 7020A1005 xx with 2 pole breakers output panel and SmartLink enabled 4 SmartPack User Manual SmartPack Touring System m Overview
16. Switch and LED Indicators Power LED DMX LED Use the Standby Control power switch to start up and shut down operation of the SmartPack When the breaker is in the On position the blue Power LED is illuminated indicating the power is on WARNING When the Standby Control power switch is in the Off position the unit is still connected to the power supply When working on exposed load circuit wiring the load cables must be unplugged or the unit disconnected from the power supply The green DMX LED indicates a DMX signal When no DMX signal is present the green LED will flash When a stable DMX control signal is present the green LED will illuminate fully Keypad Description Return to the home menu lt Move back one menu item y Accept a menu choice or store a value Increase a value or scroll through the menu Decrease a value or scroll through the menu 28 Activate the Test menu SmartPack User Manual LCD The display is a high contrast 20 character by two line backlit LCD The control symbol indicated in the top right corner of the LCD indicates the current control source El z DMX DMX 001 gt 012 El Preset Level Sequence Control Symbol Ed Test Note If you discover a blinking C in the top corner of the LCD one or more of the power cubes has exceeded the maximum operating temperature of 90 Cels
17. ack Touring Systems and the SmartPack Wall Mount unit OT II ST Munim Mutt lilin Standard Features DMX512 native SmartLink enabled for pack to pack synchronization e Thirty two programmable presets and a built in sequencer for stand alone operation Ultra quiet variable speed cooling fan Multi language user interface including English Spanish German and French e User selectable dimming curves Fully rated magnetic circuit breakers Auto restart function for day to day operation Emergency contact input with load shedding capability on wall mount models 2 SmartPack User Manual SmartPack Wall Mount The SmartPack Wall Mount unit with SmartLink enabled provides total versatility and convenience for venues requiring low profile permanently installed dimming The SmartPack Wall Mount unit may be installed with or without other system components ensuring the lowest possible cost ownership In addition a rack mount kit is available for installing the unit into an equipment rack Product Variants p w mmm k oa a lt Titam Tii Hu ununun lm TR mi m un dn II 42111
18. ch that sets the circuit to Dimmable or Hot Power constant circuit Circuits set to Circuits set to Dimmable Hot Power A A V 1 ON y DIM TON 4 DIM SmartPack User Manual Normal Menu Structure Normal Menu The normal menu is used to view system status and to set the DMX start address for SmartPack The start address range is determined by the size of your SmartPack DMX Start Address range 3 channel 001 510 6 channel 001 507 12 channel 001 501 Set the DMX start address Step 1 Scroll to DMX press w Step 2 Scroll to DMX Start Address press v Step 3 Use or to scroll the start address range Step 4 Press v to set the start address Test Menu The test menu is a tool for testing dimmers and loads In the absence of a DMX control source the test menu may also be used to set dimmer levels for snapshot into a preset Enter the Test menu From any menu press the test button gt Test Dimmer All Level 100 Set dimmer levels in the Test Menu Step 1 Use or v to select one or ALL dimmers Step 2 Use or to set a level press y The menu will progress to the next channel Step 3 Press X Exit Test Mode
19. dependent upon the other for operation but instead rely independently on the SmartLink network and specific host messages Note The SmartPack Portable dimmer packs do not share the same I O panel as the SmartPack Wall Mount Utilize the RJ45 connectors located on the rear panel of the portable unit for SmartLink In and Thru Reference the SmartPack Portable Setup Guide for output panel details I O panel to chassis ground LinkPower supply optional SmartLink Emergency DMX IN DMX Thru ESD Ground Synchronization each SmartPack and SmartSwitch in the system must have the I O board installed i e SmartLink enabled and connected on the SmartLink network Up to four SmartLink host products may be utilized on the SmartLink network e Wall Station In addition to the I O board a SmartLink host product in the system must have a LinkPower supply S LPS or SmartLink Station Power Module S SPM installed to power the wall stations The LinkPower supply powers up to four SmartLink wall stations while the SmartLink Station Power Module S SPM can power up to 16 stations When utilizing a LinkPower supply ETC reccommends installing the supply in the same host product that the station data run terminates and utilizing that same product as the station master 18 SmartPack User Manual Definitions e Host Product any SmartPack SmartSwitch Unison DRd with SmartLink or Sensor with SmartLink within a sys
20. ee Remote Record on page 15 All SmartPack and SmartSwitch products on the SmartLink network will record the current output levels for the preset that is assigned to that button Step 1 Set dimmer levels to a desired look via the test menu and or other DMX control device Step 2 Press and Hold the preset button for 5 seconds After two seconds the LED will start to blink at a 1 2 second interval If the button is held for 5 seconds a record action will be begin Ifthe button is released before the 5 seconds have elapsed recording will be canceled and the normal preset will be activated Step 3 Release the preset button The new recorded preset will activate and the LED will illuminate SmartPack User Manual Chapter 3 Service and Maintenance Service Contacting ETC about Equipment Problems If you are having difficulties your most convenient resources are the references given in this manual To search more widely try the ETC web site at www etcconnect com If none of these resources is sufficient contact ETC Technical Services directly at one of the offices listed below Emergency service is available from all ETC offices outside of normal business hours When calling for assistance please have the following information handy Your location and job name Model of SmartPack used List of other installed products and components connected to the system you are troubleshooting DMX control source
21. he previous menu Step 4 Press to return to the previous menu or press to return to the main menu The specified DMX range will display on the LCD DMX Patch DMX Patch allows the user to patch different DMX numbers to selected dimmers This menu is to be used when setting the DMX Start Address is not sufficient When DMX Patch is selected as the active DMX Mode DMX Patch will be displayed on the LCD DMX Patch Step 1 Scroll to DMX press 2 Step 2 Scroll to DMX Patch press 2 Step 3 Use or to increase dimmer channel Dimmers will be numbered 1 6 or 1 12 depending on the SmartPack channel count Initially the DMX address will patch consecutively with the dimmer channel If the DMX address should differ from the channel number press 2 SmartPack User Manual Step 4 Dim gt DMX will display Press or to change the DMX address Step 5 Press y to return to the dimmer channel selection Continue with steps 3 and 4 until all dimmers are patched to the required DMX Address Step 6 Press lt to return to the previous menu or press lt lt to return to the main menu DMX Patch will display on the LCD DMX Loss Behavior DMX Loss Behavior may be set to either Hold Last Look Fade to Preset or Wait and Fade Out Hold Last Look holds any active dimmers at whatever levels they were receiving when the data was lost The dimmers will remain on until data is restored or the SmartPack is re
22. if any Related system problems or equipment failures Americas ETC International Technical Services Department 3031 Pleasant View Road Middleton WI 53562 800 775 4382 USA toll free 1 608 831 4116 service etcconnect com Asia ETC Asia Ltd Technical Services Department Room 1801 18F Tower Phase 1 Enterprise Square 9 Sheung Yuet Road Kowloon Bay Kowloon Hong Kong 852 2799 1220 service etcasia com E Service and Maintenance United Kingdom Electronic Theatre Controls Ltd Technical Services Department 26 28 Victoria Industrial Estate Victoria Road London W3 6UU UK 44 0 20 8896 1000 service etceurope com Germany Electronic Theatre Controls GmbH Technical Services Department Ohmstrasse 3 93607 Holzkirchen Germany 49 80 24 47 00 0 techserv hoki etcconnect com 23 Maintenance Vacuum the Vents Vacuum the dust from the airflow vents regularly The interval between cleanings is dependant on the installation environment Never allow the vents to become completely clogged with dust Vacuum the Interior WARNING High Voltage Remove power from the SmartPack unit prior to removing the front cover Step 1 Remove power from the SmartPack Step 2 Remove the front cover of the SmartPack unit and detach the ground wire Step 3 Vacuum dust from the interior of the unit Use canned air to blow dust from the circuit boards to avoid possible damage from electrostatic discharge
23. ith the same fade up time hold time and fade down time as sent from the host product Sequence Synchronization Activating a sequence on any pack causes all connected SmartLink enabled SmartPack and SmartSwitch products to run the same sequence in lock step synchronization using the host product fade up hold and fade down times In addition sequence loop yes or no will be sent from the host product to all inter connected SmartLink enabled products to ensure lock step synchronization If the sequence is activated from the facepanel of a SmartPack That SmartPack will act as the host product and send its host messages to the other SmartLink enabled products in the system Each SmartLink enabled product in the system will activate the sequence as sent from the host product with steps and timing synchronized If one product in the system does not have specific step recorded and the host product sends the message to play that step the receiving product will simply ignore that command and pick up with the next recorded event SmartPack User Manual Stations Two button station types are available for use on the SmartLink network a 5 button anda 10 button station providing easy remote access to the 32 built in presets and sequencer found in the SmartPack The SmartLink Timeclock also provides access to all your presets and adds real and astronomical time functions to the SmartLink control system from a single location Wall
24. ius When you have corrected the temperature problem the error should clear If the error persists contact ETC Technical Services for assistance When configuring the SmartPack Characters or TEXT in brackets indicate an item can be selected Characters or gt Text lt in angle brackets indicate an item is selected Adjusting the Contrast of the LCD Display Press and hold lt lt and use the and buttons to adjust the contrast of the LCD display Initial Power Up Display The first time you apply power to the SmartPack you will be asked to choose a language for the operating system The language options will cycle through the following four options at three second intervals Set Language English Choisir la langue Fran ais Press y to set the displayed language option Sprache ausw hlen Deutsch Seleccionar idioma Espa ol Menu Lockout The menu lockout function restricts users from performing any changes to the current operation of the SmartPack from the facepanel When lockout is enabled the emergency contact input SmartLink station control and incoming DMX levels will still affect change in the output level of the Smartpack dimmers Set levels from the test menu prior to engaging lockout will be held until lockout has been disengaged To engage menu lockout Press and hold and buttons for a period of 5 seconds When lockout is on all local controls are disabled If a user interface button
25. lect a preset Step 4 Preset Run Instant will display briefly a To run the preset with its programmed Fade Up and Fade Down times ignore the Run Instant message The display will return to the previous menu after a few seconds of display b Press y to complete the preset in the default time of 3 seconds The display will default to the previous menu Deactivate a Preset If a Preset is active the control symbol located in the top right corner of the LCD will display the preset number and the P symbol To deactivate the preset Step 1 Scroll to Presets menu press 2 Step 2 Scroll to Deactivate Preset and press y Preset Deactivated will display briefly then returns to the previous menu Sequencer The built in sequencer in SmartPack plays a series of recorded presets sequentially The order of execution is based on the first preset and the length is determined by the number if steps configured for the sequence Fade Up Fade Down and Hold Times are determined in the preset menu and may be different for each preset The sequence can be set to loop continuously or stop after only one occurrence Setup a Sequence Step 1 Scroll to Sequencer press 2 Step 2 Scroll to Setup Sequence press 2 Step 3 Use or to select the number of steps to be included in the sequence up to 32 The Sequencer will play the steps in series with preset one as step one always Press y Loop NO will display Step 4
26. nu or by a DMX input If both levels are present it will record all levels When a new preset is recorded using the same preset number SmartPack will record over the previous levels Unless preset timing is configured otherwise presets are activated in the default fade up and fade down time of 3 seconds Record a Preset snapshot Step 1 Set dimmer levels with an external DMX source and or set test levels Step 2 Scroll to Presets menu press 2 Step 3 Scroll to Record Preset press 2 Step 4 Press or to select the desired preset number then press y Preset record will briefly display Lil Menus and Configuration 11 Setup Preset Timing Step 1 Scroll to Presets menu press 2 Step 2 Scroll to Setup Timing press v Setup Timing Preset Step will display Step 3 Press or to scroll the presets list Press v Fade Up min 03 will display Step 4 Press or to increase or decrease the Fade Up minutes Press The selection will change to the seconds field Step 5 Press or to increase or decrease the Fade Up seconds Press y Fade Down min 03 will display Step 6 Repeat steps 4 and 5 for Fade Down Press y Hold Time min 00 will display Step 7 Repeat steps 4 and 5 for Hold Time Press y when done Activate a Preset Step 1 Scroll to Presets menu press 2 Step 2 Scroll to Activate Preset and press v Number will display Step 3 Press or to scroll the list of presets Press to se
27. press is received the unit will CONTROLS LOCKED display a lockout dialog for three seconds then return ENTER UNLOCK CODE to the main status display To disengage menu lockout Press and hold and buttons for a period of 5 seconds The display returns to the main status display and all controls function normally Fat Menus and Configuration 7 Circuit Mode Selection Switches for SmartPacks with ThruPower ThruPower Relay Each circuit has a dedicated three position switch that sets the circuit to Dimmable Relay or Hot Power constant circuit nuum n n THEE EHE LH ED HR DEED HH TE HH HIPH D HU nnn nn nn m n nnn n xQ X IDI n n nn n n n nm n n 7 xQ Q AI n n n n nm n nmmm m n n l n n Circuit set Relay Circuit set to Dimmable to Circuits set to Hot Power TODO DO CHO DN EDI IC DD LH D HL EDD TH C FH ELO ILI ET HILL E LL IH E LLL DD LA ThruPower Switch CE only ON RELAY DIM Each circuit has a dedicated two position swit
28. r supply S LPS installed or an external SmartLink Station Power Supply facilitates the communication of host messages reference page 19 for host messages between SmartPack dimmer packs and the use of SmartLink stations See Stations on page 21 DRd 12 with SmartLink SmartLink LinkPower Supply Presets Sequences Sequence Timing gt SmartLink ATC Belden 8471 plus 1 14 ground Y Xi 4000 GUE i Gi i as qr CHG A SmartLink LinkPower supply is limited to four SmartLink stations Alternatively you may have up to 16 SmartLink stations when using a SmartLink Station Power Module S SPM You are limited to four SmartLink host products in a SmartLink system One SmartLink host product SmartPack SmartSwitch Unison DRd with SmartLink or Sensor with SmartLink in the system must have a LinkPower Supply or Station Power Module installed for wall station power SmartPack User Manual Assign Station Master One SmartPack in a system with wall stations installed should be configured as the Station Master The station master tracks and updates button LED states for connected wall stations when preset or sequence changes occur In addition the station master sends host messages to other SmartLink enabled SmartPack dimmer packs in the system
29. rocedure The LinkPower supply kit includes a LinkPower supply and four screws Step 1 Step 2 Step 3 Step 4 Step 5 Step 6 Step 7 EY LinkPower Supply Remove power from the control electronics a Fora SmartPack Wall Mount turn the Standby breaker off b Fora SmartSwitch relay panel turn the circuit breaker off at the breaker panel Remove the two screws securing the I O panel to the chassis Fold the I O panel down to reveal the control terminations Step 5 LinkPower supply WO board Angle the LinkPower supply board approximately 10 and insert the four pins as found on the LinkPower supply into the receptacle on the I O board Align the LinkPower supply with the four screw mounts located on the I O panel and secure with the four screws provided Do not over tighten the screws Close the I O panel and secure with the two screws Re apply power to the control electronics Kit 25 26 SmartPack User Manual Appendix B Menu Flow Chart This appendix contains the SmartPack menu structure ss uuu euun4 ploH deis neseJd ss uu dq epey deySfeseld Yoseud GAZ ay eut HEM mo 9pe4J pue Jem 1equunN jesaJg o epey 48 4 XNG WIG yoyed XING ss uw umog epe4 deis neseJg dejs nosoud Bu dmes 4 1equnN jeseJg p1009y pejeAnoeeq 1eseJd jequinN jesaJgd ejeAnov Kejaq 1exoed pp esuodsay XWG
30. s ETC s tradition of providing the highest quality product for the entertainment and architectural lighting market If you have questions regarding the operation or installation of your SmartPack system please contact ETC Technical Services at the office nearest you Using this Manual This manual contains information on the basic features and configuration for the SmartPack dimming pack with SmartLink enabled wall station integration and maintenance procedures The following symbols are used throughout this manual to alert you to danger or important information Note Notes are helpful hints and information that are supplemental to the main text A CAUTION A Caution statement indicates situations where there may be undefined or unwanted consequences of an action potential for data loss or an equipment problem WARNING A Warning statement indicates situations where damage may occur people may be harmed or there are serious or dangerous consequences of an action WARNING RISK OF ELECTRIC SHOCK This warning statement indicates situations where there is a risk of electric shock Please email comments about this manual to TechComm etcconnect com Introduction 1 Overview SmartPacks are designed to provide SCR based professional quality dimming packaged for portable touring and permanent installations ETC offers three versions of the SmartPack including the SmartPack 19 Portable Pack SmartP
31. set Wait and Fade holds any active dimmers at whatever levels they were receiving when the data was lost for a user defined amount of time and then fade those dimmers to zero in a user defined fade time The maximum wait and fade time is 59min 59sec Fade to Preset plays a user defined preset when data is lost Step 1 Scroll to DMX press 2 Step 2 Scroll to DMX Loss Behavior press 2 Step 3 Use or to select the desired Loss Behavior press y Step 4 Use or to set the values as required press 2 Step 5 Press lt to return to the previous menu or press lt lt to return to the main menu DMX Mode DMX Mode is provided as a shortcut for switching between DMX Start Address and DMX Patch The LCD will either display the DMX address range or DMX Patch depending on the mode selected Presets SmartPack features up to 32 built in presets which can be recalled without the need of any external control system For SmartLink enabled systems with a LinkPower supply installed up to four 5 or 10 button preset stations may be used for remote recall of the built in presets and sequence See Stations on page 14 In addition these 32 presets are available for use in the built in sequencer See Sequencer on page 12 For best results presets should be recorded sequentially as they would be recalled in a sequence When you record a preset SmartPack will snapshot any level whether set in the test me
32. station use with the SmartPack Portable dimmer pack requires additional hardware that is separate from the pack itself Contact ETC for assistance A LinkPower supply must be installed into one SmartPack Wall Mount and is required to operate up to four wall stations per SmartLink system The LinkPower supply is available factory installed or as a kit S LPS for field installation Reference LinkPower Supply Kit page 25 for installation instructions DRd 12 with SmartLink SmartLink LinkPower Supply Presets Sequences Sequence Timing gt SmartLink ATC Belden 8471 plus 1 14 ground s B COUGH GOCE Fu ui ni TETEG A SmartLink LinkPower supply is limited to four SmartLink stations Alternatively you may have up to 16 SmartLink stations when using a SmartLink Station Power Module S SPM You may have up to four SmartLink host products in a SmartLink system One SmartLink host product SmartPack SmartSwitch Unison DRd with SmartLink or Sensor with SmartLink in the system must have a LinkPower Supply or Station Power Module installed for wall station power 122 SmartLink Enabled 21 22 Record a Preset from a Wall Station It is possible to record a preset from a wall station if Remote Record has been enabled in the station master S
33. t products when they are connected on a SmartLink network SmartLink connected products share various configuration parameters and events known as host messages as sent from the host product Reference page 19 for host messages defined DRd12 SmartPack SmartSwitch SmartPack Portable m m t po 7 EE 252 LEEG Belden 8471 Presets Sequence Sequence timing Preset and Sequence Synchronization Default functionality is that the last SmartPack or SmartSwitch updated in the system acts as the host product and sends its host messages to the other SmartLink enabled products in the system Each product SmartPack and SmartSwitch will retain its own preset and sequence configuration as programmed but when a host product is selected each SmartLink enabled product will activate and play its sequence with the number of steps and timing fade up fade down hold time as sent by the host product Preset Synchronization Selecting a preset on any pack affects the same numbered preset to run on all inter connected SmartLink enabled products simultaneously If Preset 1 is activated from the facepanel of a SmartPack That SmartPack will act as the host product and send its host messages to the other SmartLink enabled products in the system to activate Preset 1 The preset will activate w
34. tem that sends specific host messages to other SmartLink enabled products in the system for preset and sequence synchronization e Station Master any SmartLink enabled host product with a LinkPower Supply S LPS or Station Power Module S SPM installed that is configured via the menu to control wall stations The station master will track and update LED status when preset or sequence changes occur and receive host messages from the wall stations when a button is pressed and released In addition the station master will act as the host product for preset and sequence synchronization ETC reccommends configuring the product with the LinkPower supply installed and the station data runs terminated as the station master Host Messages specific configuration settings and events sent from the host product to other SmartLink enabled products for lock step synchronization of preset and sequence playback Host messages communicated include DMX Loss Behavior Hold Last Look Wait and Fade or Fade to Preset Wait and Fade Times or Fade to Preset Number if applicable Sequence Start Stop and Loop Yes or No e Preset Fade Up Time Fade Down Time and Hold Time e Language Language selected Station Master Enable or Disable Power Up Behavior Normal or Previous State 2 SmartLink Enabled 19 Pack Synchronization It is possible to synchronize presets and sequence activation across up to four SmartLink hos
Download Pdf Manuals
Related Search