DP 01/ DP 01S DECT Phone User Guide
Contents
1. then press to end the registration procedure Once the registration procedure is finished briefly press the page button again on the base to check that all handsets registered to that base ring at the same time when an incoming call is received b To register a DP 01 ora DP 01S handset to the Base unit of a different manufacturer brand you should first set the other manufacturer s Base unit to Registration mode refer to the user manual for details Then using your Punkt handset follow the registration procedure as explained under paragraph a of this section c Toregister another manufacturer s handset to the Base unit of the DP 01 Main unit begin the registration procedure with that handset in accordance with the manufacturer s instructions then hold down the Page button on your DP 01 Base unit for 5 seconds to activate the registration procedure on the DP 01 Base unit Finally complete the registration procedure on the other manufacturer s handset according to the manufacturer s instructions 21 Select base If your Punkt handset is already registered to more than one DECT base a maximum of 4 bases are allowed you can switch between the current linked base and a new base by following the procedure described below By default the DP 01 Handset is registered to its own DP 01 Base which is identified as Base 1 Press select Handset settings and press Choose2. Call or save a number in the phone book from the call history Once a telephone number is highlighted in the call history by pressing the button you can choose either to 15 Call the selected number Select Call and press to start the call Save the selected number in the phone book Select Save and press Select New contact if you wish to create a new contact for that number refer to the Phone book section in this Guide or select Add to existing if you wish to add the selected number to an already existing contact In this case select the desired contact in the phone book and press to confirm Then select the type of number Home Office Mobile you wish to add or replace it with To replace an already existing number press amp when the option Replace number is shown a confirmation tone will be audible Answering machine TAM The Punkt integrated answering machine TAM provides 15 minutes of 7 DN total storage capacity for recorded messages Each recorded message can i i be up to 1 minute long The default setting of the TAM is not active Off and the TAM Ring count parameter is set to 10 Rings when On the TAM will answer the incoming call automatically after 10 rings 1 1 ia 3 s To activate the TAM service On and change the TAM Ring count 7 setting please read the sections below hu on d ay 3 F th J une N J Note
3. Press to confirm your choice Flash time Note If you are in France and are connected to the public analogue line PSTN network you should set Flash time 270 ms as explained below During a conversation the Flash option is normally used to access special services also known as supplementary services if these are supported by your telephone operator such as Call waiting service 3 way conference etc Please check with your telephone operator for availability of the above services Press select Base settings and press Select Flash time and press Select one of the available settings 98 ms default setting 270 ms 380 ms 900 ms If you are located in France you should choose 270 ms Press to confirm your choice Reset to default After this operation e the Call History will be emptied e the Flash time will be restored to 98 ms e the Dial mode will be restored to Tone DTMF Press select Base settings and press Select Reset to default and press Select Yes and press to confirm 20 Multi Handset configuration setting up the DP 01S Additional unit If you purchased the DP 015 kit Additional unit to make and receive calls with your DP 01S Handset you first need to register it to your DP 01 Base station Main unit or to another DECT model base
4. Select Language and press Select required language Press to confirm Answer on pickup The default setting for Answer on pick up is Off the user needs to press the key to answer an incoming call When the Answer on pickup option is set to On and the handset is located on the base station the incoming call is automatically connected answered once the handset is removed from the base station Press select Handset settings and press Select Answer on pickup and press Press to select On or Off Press to confirm 19 Base settings Set Base PIN The default base PIN is 0000 You can change it if you do not want other users to register additional handsets to your Punkt Base station Please refer to the Multi Handset section in this Guide for further information concerning the registration procedure Press select Base settings and press Select Set base PIN and press Enter the new PIN 4 digits select Done and press to confirm Note Make a note of your new PIN and keep it in a safe place Deregistration Refer to the Multi Handset section of this Guide for more details Dial mode Press select Base settings and press Select Dial mode and press Select Tone for DTMF dialing default setting or Pulse for decadic dialing
5. Then modify the name amp operates as backspace the key toggles between small letters and capital letters select Done and press to finish When finished press repeatedly to exit the phone book 14 Call history NOTICE ABOUT THE VISUALIZATION OF THE CALLER NUMBER ON INCOMING CALL After the first ringtone the caller number information will be showed on the display only if the CLI service is supported by your telephone operator and it is also activated on your own phone line According to each single operator the activation of the CLI service can be subjected to a special additional service fee Please contact your operator for further details Please note that if the caller voluntarily hides his own phone number the Punkt display will show Withheld no even if the CLI service is activate while if the CLI service is not active on your phone line the display will just show Number Unknown Access Call history Press select Call history and press The calls stored in this list are identified by the following icons L Identifies a received call answered call The caller number is shown only if the CLI service is activated on your phone line see text box above Identifies a missed call unanswered call The caller number is shown only if the CLI service is activated on your phone line see text box above t Identifies an outgoing call a dialed phone number
6. option R Button does not work correctly Why Reason 1 The Flash time setting on the Base unit is incompatible with your country s telephone network For example if you are located in France then you may have to change the default setting 98 ms toa new setting 270 ms If it still does not work correctly please set another possible Flash time value and try again make sure that the service you are trying to use is actually activated on your phone line Reason 2 The service you are trying to use is not activated on your phone line Please contact your telephone operator Possible solution Contact your telephone operator to check if the desired service is actually active on your phone line then try to set a different value for the Flash time as explained above 25 CE Declaration of Conformity In accordance with European standards ISO IEC Guide 22 and EN 45014 and with reference to Annex IV of Council Directive 1999 5 EC R amp TTE We Promelit S p A Via Modigliani 20 20092 Cinisello Balsamo Italy declare under our sole responsibility that this device meets the essential requirements and other relevant regulations laid down in Directive 1999 5 EC In particular this product is compliant with the following standards Radio Part ETSI EN 301 406 V 1 5 1 TBR6 EMC Electromagnetic Compatibility EN301489 1 V 1 8 1 EN301489 6 V 1 3 1 Electrical Safety EN60950 1 2001 A11 2004 Additionally the
7. service activation Note If you are in France and are connected to the French public analogue line PSTN network before using the Flash button you should set the Flash time parameter to 270 ms as explained in the Base settings section of this Guide During a conversation the Flash option is used normally to access special services also known as supplementary services if supported by your telephone operator such as the Call waiting service 3 way conference etc Please check with your telephone operator for availability and activation of the above services on your phone line In order to use the Flash option during an external conversation Pres Select Flash and press R will appear on the display Dial additional digits according to the instructions provided by your telephone operator for example in Italy you can dial R2 to switch between 2 external connected calls and then dial R3 to activate the 3 way conference service 13 Phone book Enter a new contact in the phone book Press to open phone book Press to select New Usethe keypad to enter the name amp operates as backspace Press the key to toggle between lower case abc and upper case ABC mode Select Done and press to confirm Press to select the option Home Office Mobile you wish to assign to the inserted number
8. From the DP 01S handset the TAM option is accessible only if paired with a DP 01 main unit base TAM data is stored in the DP 01 main unit base only Activate de activate the answering machine TAM Press to open the answering machine menu Press and select Settings Press Press to toggle the answering machine On Off When the answering machine TAM is on the TAM icon will be shown on the display in standby mode Greeting message Record Listen Delete For the default setting only an acoustic tone will be played when the TAM feature is activated and an external incoming call is received If you wish to record your own greeting message listen to it or delete it please follow the procedure below Press to open the answer machine menu Press and select Settings Select Record greeting and press Select Record and press You now have 30 seconds to record your own greeting message which will be played on incoming calls when the TAM is activated press amp to stop the recording When you have finished recording the greeting select Listen and press to listen to the greeting message which is now stored in your Punkt phone press amp to stop playback Select Delete to delete the recorded greeting message after this operation only the default acoustic tone will be heard by the caller and no greeting message will be played when
9. Select base and press Select the base you wish to connect to If you choose the Auto option the handset will search for the nearest available base with which it was registered in advance provided the Base is connected to the mains and there is sufficient signal strength to allow the connection Deregistration If you want to deregister a Handset from your Punkt DP 01 Base you can do so from your DP 01 DP 01S handset or from another handset connected to the same Punkt DP 01 Base as explained below Press select Base settings and press Select Deregistration and press Insert the PIN of the Punkt DP 01 Base unit 4 digits and select Done Press Select the Handset number you want to deregister from those shown in this list Press to confirm cancellation Note If you wish to re use the cancelled Handset on the same base you must repeat the Registration procedure as explained earlier in this Guide 22 Internal calls internal direct calls and external calltransfer If you have more than one handset registered to your Punkt DP 01 Base unit you can make internal calls between handsets registered on the same DECT Base and also transfer an incoming external callto another handset To place an internal direct call Press select Internal call and press Select the handset you wish to call and press to start the call To
10. and press to confirm Enter the number using the keypad Select Done and press to save the contact and end the procedure Make a phone call using the phone book Press to open the phone book Use to browse your contacts Press to select the required contact Use to browse phone numbers Press to start the call Press to end the call Delete a single contact from the phone book Press to open the phone book Use Sto search for the contact you wish to delete then select it by pressing O Select Edit and press Select Delete and press Select Delete contact and press Select Yes and press to confirm Delete all contacts from the phonebook Press to open the phone book Use toselect Delete all and press Select Yes and press to confirm Modify a contact s details name and or associated phone numbers Press to open the phone book Use tosearch for the contact you wish to modify then select it by pressing Select Edit and press Ifyou wish to modify one of the 3 possible telephone numbers related to that contact select it in the list with and press Then modify the telephone number operates as backspace select Done and press to finish Ifyou wish to modify the contact s name select Name with OQ S and press
11. DP 01 DP 01S DECT Phone User Guide Punkt Notes l1 Ifyou purchased the Pu it to make and receive calls with your handset you first need to register it to your DP 01 Base station Main unit or to another DECT model base station In this case please refer to the Multi Handset section of this User Guide for the registration procedure 2 Ifyour DP 01 Base station is connected to the French phone network to use the Flash option during a conversation you first need to set the Flash time parameter to 270 ms In this case please refer to the Base settings section of this User Guide 3 Please note that the DP 01 is designed for analog telephony however It is also possible to connect it to an PSTN analog port of a ISDN line Please visit http www punktgroup com to download the latest available version of this User Guide The current User Guide version is Ver 1 01 Nov 24th 2011 Change Log User Guide version and date Modified sections Ver 1 01 Nov 24th 2011 Second release updated for US market version Contents Content of the gift box Technical specifications Health amp Safety instructions Care of the product Disposal of the product and batteries Installation Display icons and function keys Basic use of the phone initial settings In call options Phone book Call history Answering machine TAM Handset settings Base settings Multi Handset config
12. Insert the power cable for both DP 01 and DP 01S models Connect to phone and power sockets A specific adaptor for your phone socket and or your mains socket may be requested depending on the country you are in and the standard socket configuration Place the handset on the base for battery charging a docking sound indicates that the handset has been placed correctly on the base Let the batteries to charge for at least 16 hours before using your phone for the first time Subsequently 8 hours will be sufficient for a full recharge For DPO1 Main unit only Display icons and function keys With reference to the diagram below A Select Send Yes Cancel End No Backspace Exit Menu hold for 2 seconds Power On Off hold for 2 seconds in Home screen w Scroll up and Scroll down Phone Book Answering machine Signal Power Number of answering machine message s Battery Power Handset Number Missed call icon Upper Lower Case Keypad Per Udt tat ya Page Button May not appear in past versions of the phone 10 OO 00 OO I G Dan J F Ren ce H 11 35 a Monday 26th June c E SON fh oo A 1 D LA N B a aAa OES C aN A C 1 we2 3 ED EEH HTA Sy og a a Nr SD 5 o Punkt Basic us
13. above mentioned product conforms to the following standards ETSIES 203021 3 V2 1 2 Conformity to Directive 2009 125 EC ecodesign requirements for energy related products is ensured according to the following regulations External power supplies Regulation EC No 278 2009 Standby and off mode Regulation EC No 1275 2008 not applicable This device is intended for analogue phone lines in your network Country specific requirements have been taken into consideration According to the above statement this product is marked with the following mark A copy of the 1999 5 EC Declaration of Conformity is available at this internet address http www promelit it punkt EC declaration pdf Place of issue Cinisello Balsamo MI ITALY Date of issue August 4 2010 26 Technical Information AC DC Power Adapter Information AC DC Adapter for the Base DP 01 and Handset Charger DP 01S Adapter model DYS052 050070W 1 Input voltage 100 240V AC 50 60Hz Output voltage 5 0V 0 7A Use only the supplied AC adapter Donot place the unit in direct sunlight or subject it to high temperatures Batteries Information Rechargeable batteries with normal use Number of batteries 2 Battery type Ni MH AAA size rechargeable batteries Capacity 1 2V 700 mAh Talk time about 10 hours Standby time about 100 hours Time required for first charging about 16 hours Time r
14. an incoming callis received 16 Listen to received voice messages When the TAM is activated the number of new voice messages received will be notified on the display according to the indication below in this example only 1 voice message has been left by external callers In order to play received voice messages follow the procedure below Listen to all new messages Press Select New and press Press to play all After a single new voice message has been played for the first time it will subsequently be classified as an old message You can replay it by selecting the Old option in the main TAM menu Listen to a selected new message Press Select New and press Press to browse the messages Press to select Select Play and press to play the message After a single new voice message has been played for the first time it will subsequently be classified as an old message You can replay it by selecting the Old option in the main TAM menu Options for a single voice message call the caller listen or delete a message Press Select the New or Old folder and press Press to browse the messages Press to select the required message At this point e Select Play and press to play the message Select Call and press to call the caller directly Select Delete and
15. and DP 01S handsets is explained in a later section of this User Guide For some countries a specific Power adaptor and or a telephone line adaptor may be provided inside the gift box Please check this with your dealer Technical specifications Type of technology RF channels Frequency range used Channel spacing Audio coding Type of modulation Maximum transmitted RF power Operating range Handset power supply Battery charge duration autonomy Time required for first charge Time required for subsequent charging cycles Base dimensions and weight Handset dimensions and weight Display Connectable handsets to a single DP 01 base unit Connectable bases to a single Punkt handset Dialing type Phone book capacity Supported Languages DECT Digital Enhanced Cordless Telecommunications standard with GAP Generic Access Profile profile 10 channels For EUROPEAN version 1 881 GHz 1 897 For US version 1921 636 MHz 1928 448 MHz 1 728 MHz ADPCM 32 Kbit per second GFSK 250 mW 24 dBm max 40 mindoor max 200 m outdoor Transmission range may vary according to the position of the base construction materials used in the area electromagnetic pollution interference with other radio devices etc DECT performance levels are given as areference only and are not guaranteed 2 x AAA Ni MH rechargeable batteries 1 2V 700 mAh up to 100 hours in stand by mode and up t
16. bout what will disable alarm equipment contact your telephone company or a qualified installer CAUTION WARNING Any changes or modifications to this product not expressly approved by the manufacturer or other party responsible for compliance could void not only your authority to operate this product but also the limited warranty According to telephone company reports AC electrical surges typically resulting from lightning strikes are very destructive to telephone equipment connected to AC power sources To minimize damage from these types of surges a surge arrestor is recommended Hearing Aid Compatibility HAC This telephone system meets FCC standards for Hearing Aid Compatibility FCC Part 15 amp SAR Information This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation Privacy of communications may not be ensured when using this phone FCC PART 15 105 b Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not 30 installe
17. ct Telephone Jack Requirements RR Wa ate To use this phone you need an RJ11C type modular telephone jack which rae might look like the one pictured here installed in your home If you don t Modular a elephone have a modular jack call your local phone company to find out how to get line jack one installed 28 FCC Compliance Information FCC Part 15 Part 68 SAR test S measurements FCC Part 68 Information valid for DP 01 model only Note The base unit of the DP 01S model Additional unit should be connected ONLY to the electrical mains by using the power adaptor provided in its original package The base unit of the DP 01S model Additional unit acts only asa battery charger for the DP 01 Handset units For this reason it should NOT be connected to the PSTN analogue telephone line network 1 The DP 01 model complies with Part 68 of the FCC rules and the requirements adopted by the ACTA On the bottom of this equipment is a label that contains among other information a product identifier in the format US A2TW401BDP01 If requested this number must be provided to the phone company 2 The DP 01 model uses the RJ 11 Universal Service Order Code USOC jack 3 Aplugand jack used to connect this equipment to the premises wiring and telephone network must comply with the applicable FCC Part 68 rules and requirements adopted by the ACTA A compliant telephone cord and m
18. d and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna that is the antenna for radio or television that is receiving the interference Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for additional suggestions FCC RF Exposure Compliance Information This product complies with FCC radiation exposure limits set forth for an uncontrolled environment under the following conditions The base must be placed to allow a minimum of 20 cm 8 inches between the antenna and all persons during normal operation The base must not be collocated or operated in conjunction with any other antenna or transmitter The handset is designed for body worn operation and meets FCC RF exposure guidelines when used with any belt clip carrying case or other accessory supplied with this product all necessary accessories are inclu
19. ded in the package any additional or optional accessories are not required for compliance with the guidelines Third party accessories unless approved by the manufacturer should be avoided as these might not comply with FCC RF exposure guidelines SAR Tests amp Measurement The SAR Specific Absorption Rate tests are performed in positions and locations eg at the ear as required by the FCC for each model The SAR value for this handset when tested for use at ear is 0 054 mW kg Any questions regarding this compliance information statement should be directed to Please contact the Punkt point of sale nearest you or contact us via the form available on the Punkt web site at www punktgroup com 31 www punktgroup com info punktgroup com Tel 41 91 924 9003 Fax 41 91 924 9004 Punkt Tronics AG Via Losanna 4 CH 6900 Lugano Switzerland Punkt is a registered trademark of Punkt Tronics AG
20. e of the phone initial settings Menu language selection at first power on During the very first handset power on the list of selectable languages is shown automatically on the display Please select your language and press the button to confirm Later you can change the current language at any time as explained below Change the menu language The Punkt handset DP 01 DP 01S supports the following menu languages English English USA French German Italian Spanish Danish Swedish Finnish Norwegian Dutch Press select Handset settings and press Select Language and press Select required language Press to confirm Make a phone call Enter the number using the keypad to call a contact stored in the phone book refer to the Phone book section of this Guide Press to start the call Press to end the call Set time date Time and date settings are stored in the Punkt base station For this reason if the power cable is disconnected and then reconnected the previously set time and date will be cleared and the display will show default values 00 00 Friday lst Jan In this case you should reconfigure the time and date settings or wait for an incoming call with time and date information provided by your telephone operator Normally if you can see the CLI calling number on an incoming call then you can also obtain time and date settings automatically fro
21. equired for the next about 8 hours charging cycles Use only 2 Ni MH type AAA size 1 2V 700mAh rechargeable batteries as the ones provided in this package or with identical mechanical and electrical specifications Leave the handset located on the base unit for DP 01 model or battery charger for DP 01S model for 16 hours before using the DP 01 handset for the first time After that time the batteries will be fully charged and the handset can be used to make and receive phone calls Next charging cycles will take around 8 hours from full discharge Keep batteries out of reach of children When the batteries charging level gets low the handset beeps and shows a low battery alert recharge the batteries Rechargeable Battery Warning This equipment contains 2 rechargeable Nickel Metal Hydride Ni MH batteries Nickelisa chemical known to the state of California to cause cancer Donot short circuit the batteries The batteries in this equipment may explode if disposed of in a fire Donot charge the batteries in any charger other than the original DP 01 DP 01S handsets itself Using another charger may damage the battery or cause it to explode 27 CAUTION Risk of explosion if battery is replaced by an incorrect type Rechargeable batteries must be recycled or disposed of properly Do not open or mutilate the batteries Remove the batteries from the handset before shipping this produ
22. he product All electrical and electronic equipment EEE must be disposed of separately from general household waste at sites designated by local authorities Ifa product displays the symbol of a crossed out rubbish bin the product is subject to European Directive 2002 96 EC The appropriate disposal and separate collection of used equipment help to prevent damage to the environment and health They are a precondition for the re use and recycling of used electrical and electronic equipment For further information on how to dispose of your used equipment please contact your local authority your refuse collection service or the dealer where you purchased the product Installation To install your Punkt phone DP 01 Main unit or DP 01S Additional unit please follow the steps below 1 Remove the back cover of the phone insert your finger in the opening near the charging contacts and remove the battery flap Insert the batteries into the handset then replace the cover be sure to observe the correct polarity indications and as shown inside the battery compartment Insert the phone cable for the DP 01 Main unit only not for the DP 015 Additional unit The base unit of the DP 01S serves only to charge the handset batteries You therefore need only connect the power adaptor cable to this base unit You do not need to connect the phone cable to the base unit of the DP 01S
23. hone calls if the main unit is disconnected from the electrical network Werecommend that the base unit should be located in a place not easily accessible by young children and near a wall power socket When inserting the batteries in the handset ensure correct polarity of the batteries as indicated by the diagram in the battery compartment Always keep batteries out of reach of children Charge the battery for the first time for at least 16 hours before use Subsequently a recharging time of 8 hours will suffice for a full re charge We recommend that you do not use the phone to make or receive calls during initial battery charging Fit only recommended rechargeable batteries AAA size R03 Ni MH 1 2V 700mAh i e never use a different battery type or non rechargeable batteries conventional batteries as this could result in significant health risks and personal injury Do not attempt to open or damage the batteries Do not throw batteries into the fire they could explode Read the section Disposal of the product and batteries for more details When the phone is not in use put the handset on the base in order to keep the batteries charged When battery level is low a warning tone will be emitted by the handset Put the handset on the base to recharge the batteries Ifthe telephone is not used for a prolonged period for example 1 month it is recommended that batteries should be removed from the un
24. it Always keep batteries out of reach of children The display is protected by a plastic film Please remove the protective film The operation of medical appliances may be affected Be aware of the technical conditions in your particular environment e g doctor s surgery Donot hold the rear of the handset to your ear when it is ringing as this entails a risk of serious and permanent damage to your hearing The handset may cause an unpleasant humming noise in hearing aids Donot install the phone in a bathroom shower room or in locations where there are high levels of humidity The handset and base station are not splash proof Donot use your phone in environments where there is a potential explosion hazard e g paint shops The operating temperature for use of this product is between 0 C and 35 C while the non operating temperature is between 20 C and 45 C CAUTION RISK OF EXPLOSION IF BATTERIES ARE REPLACED BY AN INCORRECT TYPE DISPOSE OF USED BATTERIES ACCORDING TO INSTRUCTIONS GIVEN IN THE SECTION DISPOSAL OF THE PRODUCT AND BATTERIES IN THIS GUIDE Care of the product Cleaning the product Wipe the base and the handset with a damp cloth do not use solvent or an antistatic cloth Never use a dry cloth This can cause static Contact with liquids If the handset comes into contact with liquids Switch off the handset and remove the batteries immediately Allow the liquid to drai
25. m the telephone network Otherwise this will not be possible Please contact your telephone operator for more information Press select Time date and press Enter the time Enter the date Select Done and press to confirm Change the ringtone melody Press select Sounds and press Select Ring tone and press Press to select your favorite sound Press to confirm 11 Change the ringtone volume disable ringtone Press select Sounds and press Select Ring volume and press Press Sto select the required level 1 6 where level 1 stands for Ringtone mute Press to confirm the choice Activate De activate key tones 12 Press select Sounds and press Press Sto select Key tones Press to toggle key tones On Off In call options Hands free mode Whenin call press on the Hands free option to toggle On Off Mute When incall press and select on the Mute option to toggle Mute On Off Note When the mute option is On the other party will not hear your voice Volume control When incall press and select Volume Press Press to adjust the volume Press or wait 2 seconds to return to the in call menu Call Transfer Refer to the Internal calls section in this Guide for further details Flash R button
26. n from the handset Patall parts dry then place the handset with the battery compartment open and the keypad facing down in a dry warm place for at least 72 hours not in a microwave oven etc Donot switch on the handset again until it is completely dry When fully dried out it will often be possible to use the handset again although some problems could arise Oxidation caused by liquids such as water that has penetrated into the phone can cause serious functional problems Such problems are not covered by the warranty service Product transportation If transporting this product use the original packaging to protect the product from potential damage Wall mounting solution The base station can be mounted on a wallif preferred A magnet in the base station next to the charging contacts holds the handset vertically during the charging phase To ensure that the phone does not become detached from its base and fall to the ground make sure the handset is properly seated on the base station before removing your hand from the handset Damage and or broken parts due to user negligence in this phase are not covered under the terms of the warranty Disposal of the product and batteries European WEEE Directive 2002 96 EC Batteries should not be disposed of in general household waste Observe local waste disposal regulations details of which can be obtained from your local authority or the dealer where you purchased t
27. none TAM Ring count 10 Rings Speaker On 24 FAO Frequently Asked Questions Problem I can t see the caller s number when I receive an incoming call Why Reason the CLI service is not activated on your phone line Possible solution Contact your telephone operator for activation ask also if there is an additional price to be paid for activation Please note that if the caller hides his own phone number the Punkt display will show Number withheld even if the CLI service is active while if the CLI service is not active on your phone line the display will simply show Number unknown Refer to the Call History section in this Guide for more details Problem Even though I have set up the correct time date settings the display still shows 00 00 Friday Ist Jan Why Reason The power adaptor power cable has been disconnected from the base unit or from the electrical wall socket mains Possible solution Reconnect the power adaptor to the base and reset the time date If the CLI service is enabled on your phone line you can also simply wait for the first incoming call to ring Problem When the TAM is On the device answers after too longa time 10 Rings Why Reason The TAM Ring count parameter is set on too long a value example 10 Rings Possible solution Change the TAM Ring count parameter as explained in the TAM section of this User Guide Problem The Flash
28. o 10 hours in conversation mode 16 hours 8 hours 155 mm x 48 mm x 50 mm x 175 gr including connector 155 mm x 48 mm x 20 mm x 125 gr without batteries 1 6 horizontal 128 x 64 dots PWM back lit with black font on white background 6 4 DTMF tone dial default setting or pulse mode decadic dial 100 contacts with 3 numbers for each entry English English USA German Italian French Spanish Swedish Norwegian Danish Finnish Dutch Note English USA it is used for displaying time and date in American format MM DD YYYY and 12 hours AM PM Visual answering machine TAM with message registration sorted by date and time Total storage capacity for recorded messages 15 minutes max 1 minute for each message Note the TAM service is accessible from a DP 01S handset only if paired with a DP 01 base unit TAM data is stored in the DP 01 base unit only Nominal working temperature Extreme working temperature Relative humidity 15 to 35 C 0 to 40 C 5 to 75 Note Battery charging time and lifetime depend on phone usage by the user If batteries are not used properly the actual values for both parameters may differ from the information given above Health amp Safety Instructions Only use the mains unit and the phone cord supplied Both the power cord and the phone cord must be plugged in at all times Itis not possible to make and receive p
29. odular plug is provided with this product DP 01 model only It is designed to be connected to a compatible modular jack that is also compliant See installation instructions for details 4 Onthe DP 01 model the REN information is used to determine the number of devices that may be connected to a phone line Excessive RENS on a phone line may result in devices not ringing in response to an incoming call In most but not all areas the sum of RENs should not exceed five 5 0 To be certain of the number of devices that may be connected to a line as determined by the total RENs contact the telephone provider For products approved after July 23rd 2001 including this product the REN value is part of the product identifier that has the format US AAAEO TXXXX The digits represented by are the REN without a decimal point e g 03 is a REN of 0 3 For earlier products the REN is separately shown on the label 5 Ifthis equipment DP 01 model only causes harm to the telephone network the telephone company will notify you in advance that temporary discontinuance of service may be required But if advance notice isn t practical the telephone company will notify the customer as soon as possible Also you will be advised of your right to filea complaint with the FCC if you believe it is necessary 6 Thetelephone company may make changes in its facilities equipment operations or procedures that could affect the operation of
30. press to delete the selected message Delete all voice messages Press Select the New or Old folder and press Press to select Delete all Press to select Yes and press 17 STSI Listen to old voice messages After a single new voice message has been played for the first time it will subsequently be classified as an old message You can play it again by selecting the Old option in the main TAM menu The procedure to listen an old voice message and the available options are the same as described for new voice messages above refer to above sections for more details Change the number of rings before TAM activation Press Select Settings and press Press Sto select Ring count and press Use Oto choose one of the available values and press to confirm Set the speaker ON OFF while listening to voice messages 18 Press Select Settings and press Press Sto select Speaker and press to toggle the speaker On Off While listening to a recorded voice message you can press the button to toggle the speaker On Off Handset settings Registration Refer to the Multi Handset section of this Guide for more details Select base Refer to the Multi Handset section of this Guide for more details Change language Press select Handset settings and press
31. station Please refer to the Registration procedure explained under point a below Note If another manufacturer s products are connected to the Punkt DP 01 Base unit only the ability to make and receive phone calls is guaranteed according to the DECT GAP standard Proprietary features for example TAM service or CLI display may not be available if another manufacturer s products are being used with Punkt products Registration a To register a DP 01 ora DP 01S handset to the DP 01 Base unit please follow the procedure below Onthe DP 01 or DP 01S handset press select Handset settings and press Select the Registration option and press Select Base 1 and press if you have only one Punkt Base unit DP 01 Main unit already available and switched on If your Punkt handset was previously registered to another Base unit you can select Base 2 or Base 3 4 to keep your handset s previous registration setting s with that base unit Insert the base PIN code 4 digits default 0000 then press to highlight the Done option Press The message Press and hold page button on base will appear on the display Hold down the page button on the DP 01 base until the display shows the list Handset 1 2 3 4 5 6 then release the page button Select your Handset number from the list that appears default selection Handset 2
32. the equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service 29 7 Iftrouble is experienced with this equipment for repair or warranty information please contact the Punkt point of sale nearest you or contact us via the form available on the Punkt web site at www punktgroup com If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved 8 This equipment contains no user serviceable parts For repair and warranty information contact the Punkt point of sale nearest you or contact us via the form available on the Punkt web site at www punktgroup com 9 Connection to party line service is subject to state tariffs Contact the state public utility commission public service commission or corporation commission for information This equipment is hearing aid compatible If you experience trouble with this equipment contact the manufacturer see the cover of this manual for contact information or an authorized agent 10 Ifthe equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved 11 Ifyour home has wired alarm equipment connected to a phone line be sure that installing the system does not disable your alarm equipment If you have questions a
33. transfer an external call to another handset During an external conversation on handset 1 press select Transfer and press With select the handset you wish to transfer the call to for example Handset 2 and press amp to start the internal call the external caller will remain connected with an intermittent acoustic tone When Handset 2 answers the internal call on Handset 1 press the button to end the internal call and transfer the external call to Handset 2 23 Factory default settings HANDSET UNIT SETTINGS Handset number Handset 1 Menu language user selectable at first Handset power on Answer on pickup Off In call earpiece volume 5 In call speaker phone volume 5 Ring tone melody Motion Ring volume 5 level 1 stands for Ring mute Key tones On Connected Base Base 1 BASE UNIT SETTINGS for DP 01 Base unit only PIN code 0000 Flash time R key 98 ms Dial mode Tone DTMF Predefined associated handset Handset 1 Time date 00 00 Friday lst Jan Phonebook empty Call history empty Settings will be restored to the above values if the user carries out the Reset to default procedure explained in the Base settings section TAM TELEPHONE ANSWERING MACHINE SETTINGS for DP 01 Base unit only Answering machine status Off not active Voice message folders New and Old empty Pre recorded greeting message
34. uration Internal calls internal direct calls and external call transfer Factory default settings FAO Frequently Asked Questions CE Declaration of Conformity Technical Information FCC Compliance Information oA N Oo A 10 ll 13 14 15 16 19 20 21 23 24 25 26 27 29 Content of the gift box Please check that all of the below items are contained in the gift box of your Punkt DP 01 Main unit DP 01S Additional unit 1 Punkt base unit with external connectors for Power and Line plugs Punkt handset unit identical for both DP 01 and DP 01S models Power adaptor with power cable to be connected to the base unit Telephone line cable for connection to the DP 01 Main unit only 2x AAA Ni MH rechargeable batteries 1 2V 700 mAh for the handset unit a FP WN 6 Technical Safety amp Compliance Information sheet Regulamentary Norms for USA 7 Quick guide 8 Regulatory norms for EU Countries 9 International Warranty For the DP 01 model Main unit the base unit incorporates both the DECT base station and the battery charger For the DP 01S model Additional unit the base unit includes only the battery charger In the latter case to make and receive calls with this handset you need to register it to another DECT base station for example the base station of your Punkt DP 01 Main unit The registration procedure for a Punkt handset valid for both the DP 01
Download Pdf Manuals
Related Search