Genie GK-R Instructions / Assembly
Contents
1. o Mounting Keypad The keypad MUST be mounted within sight of the garage door s at least 5 feet above the floor and clear of any moving door part i head gap 2 Drill 1 16 pilot hole for the top mounting screw included 3 Install a screw into the pilot hole leaving a 1 8 gap between the screw head and wall 4 Hook the keypad slotted mount on back over the screw Continued other side 3 Mounting Keypad Atemporary PIN allows temporary access to your garage by repair persons meter readers etc while you are out if you so desire 5 Mark and drill a pilot hole for the bottom screw and secure keypad to wall DO NOT overtighten 6 Reinstall batteries and cover Resetting PIN If you have forgotten your PIN or you fear it may have fallen into unauthorized hands you must erase the old programming 1 Enter your current PIN and press Program key 3 times 2 Enter a temporary PIN and press Program key PROGRAM NOTE The temporary PIN is automatically cancelled whenever you enter your normal PIN after the temporary PIN is set D PROGRAM g If the Keypad backlight does not come on this indicates the need To erase follow these simple steps to replace the batteries No programming is lost when replacing the 1 Press and hold Program key and then the Up Down key for batteries 5 seconds or until the LED starts to slowly blink When blinking stops you have successfully2. erased the old programming 2 Go back and follow the steps in Setting Up a Pin and Programming Replacing Batteries Changing Your PIN 1 Remove battery cover and batteries 1 Enter your current PIN then press Program key direction for and terminals 2 Enter your new PIN press Program key 2 Replace batteries with same type batteries and check proper Additional Genie products can be ordered through your local GENIE Professional Dealer To locate a dealer near you call 800 OK GENIE If the first five digits of your serial number fall between 10289 and 11188 contact Genie for assistance 800 354 3643 FCC and IC CERTIFIED This device complies with FCC Part 15 and RSS 210 of Industry Canada This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which may be determined by turning the equipment OFF and ON the user is encouraged to try to corre
3. will automatically stop fully open or closed When the door has stopped moving pressing on any single button will activate door until backlight goes off 30 seconds NOTE Rapid blinking of the red LED on the Powerhead indicates an error When the blinking stops you must start programming steps over Using The Keypad 1 U 2 Press Up Down key Door opener will run E C EA For multiple doors only 1 Enter your PIN 2 Press Up Down key 3 Press the number of door to operate Door opener will run For multiple doors only Emr SF 1 Enter your PIN 2 Press Up Down key Opener LEDs will stay on steady ee 3 Select the number of the door you want to program 1 2 or 3 4 Press Up Down key again Opener LEDs will turn off 5 Press Up Down key again Door opener will run Each door MUST be programmed separately You MUST start all steps over when programming multiple doors NOTE Pressing any key will stop or start the opener while the door is in motion The door will automatically stop fully open or closed When the door has stopped moving pressing on any single button will activate door until backlight goes off 30 seconds NOTE Rapid blinking of the red LED on the Powerhead indicates an error When the blinking stops you must start programming steps over
4. GENE Keypad Overview Program Key CO Do Doo LED Flashing Up Down Key enter Keypad Off Keypad On Keypad Flashing Keypad LED s Successful Entries The Keypad s LED will flash on and off each time you press a key indicating the keypad has accepted each entry 7 Tiki The Keypad s LED and Program key will flash slowly Keypad lights will remain ON for 30 seconds if you have entered a valid PIN or have successfully programmed your Keypad 7 j will go OFF Retry failed step Preparation for Use Single Door Wireless Keypad Instructions FOR YOUR CONVENIENCE IT S EASIER TO PERFORM PROGRAMMING BEFORE MOUNTING KEYPAD A moving door can cause serious injury or death e Keep people clear of opening while door is moving e DO NOT allow children to play with wireless keypad e Wall control should be mounted within sight of door at least 5 feet above floor and clear of moving parts e During programming the door opener could begin to run so stay away from the moving door and its parts To keep the door from moving close the door and disconnect it from the opener by pulling the Emergency Release Cord If Safety Reverse does not work properly e Close door and disconnect the opener using Emergency Release Cord e DO NOT use door opener remote or wireless keypad e Ref
5. ct the interference by one or more of the following measures 1 Re orient or relocate the receiver antenna 2 Increase the separation between the opener and receiver 3 Connect the opener into an outlet on a circuit different from that to which the receiver is connected and 4 Consult your local dealer 4
6. er to Door and Door Opener Owner s Manuals before attempting any repairs Failed Entry The Keypad s LED and Program key will light Keypad will flash quickly if you have entered an invalid PIN or have failed to program your Keypad correctly and then Change your keypad to work with ALL Genie Intellicode openers by using the following steps 1 Enter 3 5 7 and press the Up Down key 2 When the keypad lights stay on steady 3 Hold the Program key down until the LED changes from green to red 4 Release the Program key and allow your keypad to go dark Your keypad is now set for ALL Genie model openers 38318501760 Setting Up a PIN eE Press in order 3 5 7 Press the Program key Enter your new PIN 3 8 characters Press Program key Your single door keypad is ready for programming woe gt For multiple doors only Enter your new PIN 3 8 characters Press Program key 2 times 1 2 3 Now press the number of doors you need to control 2 or 3 4 Press Program key After step 4 repeat the following steps for each door i De 1 Enter your PIN and press the Up Down Key Green Red wW 2 Enter number of door 2 or 3 3 Hold the Program keydown until the LED changes from green to red 4 Release the Program keyand allow your keypad to go dark Your keypad is
7. now set for all Genie model openers on the DOOR NUMBER CHOSEN Your multiple door keypad is ready for programming Bg gt Programming Locate Your Opener s Programming Buttons and LED New Genie Openers RADIO SIGNAL LEARN CODE a If your opener has a black antenna wire and serial number beginning with a number less than 10 for older Intellicode openers the Learn Code button and LED will be near the antenna You may have to open the light lens b If your opener does not have an antenna you have an external receiver The Learn Code Button and LED are inside You must remove the cover to access the learn code button Synchronizing Keypad to Opener PROGRAM HOLD 2 seconds 1A Press and hold Program Set key for 2 seconds The round LED turns blue and then goes off The long LED will begin flashing purple RADIO SIGNAL E LEARN SIGNAL LEARN CODE CODE 1B Press the Learn Code button and LED will blink NOTE The Learn Code button and LED may be located under the light lens or you may have to remove your unit s cover Cyt Hert bl to Eer as 2 Enter your PIN 3 Press Up Down key Opener LEDs will stay on steady v Opener Yv 4 Press Up Down key again Opener LEDs will turn off 5 Press Up Down key again Door opener will run NOTE Pressing any key will stop or start the opener while the door is in motion The door
Download Pdf Manuals
Related Search