Art Decor I-04-5092-CH Installation Guide
Contents
1. TEKNO 25 INSTALLATION INSTRUCTIONS STEP 1 Installing Supports OUTSIDE POST 4 4 4 a i ki 7 a u LA A CARRIERS e i b Coe Uy E al y COVER PLATE 0 a ma BACK PLATE w T i 4 INSIDE POST Height calculation for regular clips Add 1 to length of drapes plus at least 1 2 clearence from the floor This measurement is the distance from floor to center point of Back Plate Please note drapes should not touch rail install pin on hooks with this in consideration I l M 6 BOLT COVER PLATE INSIDE POST 1 Install Back Plate to wall Make sure all M 6 bolts are level If you have a spliced track the Center Support must be installed at the position of splice Cover Back Plate with Cover Plate 3 Screw on Inside Post very securely Do not leave any play STEP 2 Splice track if necessary 1 Join the track sections together Tighten set screws Screw Center Support directly into center hole of Splice CENTER SUPPORT STEP 3 Installing Outside Posts OUTSIDE POST 1 Loosen all screws on Outside Posts 2 Slide Ouside Posts into back channel of Rail 3 Align Outside Posts with Inside Posts from Step 1 STEP 4 Mount rail onto supports Slide Outside Posts over Inside Posts 2 Once all Outside Posts including Center Supports are in place tighten posts securely by turning clockwise 3 Tighten set screws 4 Finish2. ed result for Center Supports 5 Finished result for side posts STEP 5 Hand draw systems 1 Install Finials and then click in carriers 2 Attach Fling Rod to side of drape you wish to operate from by clipping it into first carrier 3 Use plastic plug to lock last carrier in place so end of drape does not move when the drape is closed STEP 6 Installing regular carriers corded system 1 Install Finials and then click in carriers 2 For center opening tracks greater than 84 click in plastic plug at center point of rail STEP 7 Cord Draw Systems Installing Pulley 1 Attach pulley to cord Stretch pulley until cord is tight It is not necessary to use excessive tension Mark spot with pencil on wall or floor Remove cords and install pulley then re install cords e THE PULLEY MUST BE INSTALLED IT IS THE LAW FAILURE TO DO SO CAN RESULT IN INJURY TO CHILDREN OR PETS 2 IF NEEDED To adjust CONTROL cord drop pull cord through master carrier until pulley is at desired height Pull cord an extra few inches and knot cord at proper spot When you install the pulley the cord will slide back into place INSTALLATION OF EURO SCOPE UPGRADE KONTUR NEXGEN TEKNO 25 TEKNO 40 STEP 1 Assembling track when splicer is included STEP 3 Installing track Dies 1 Place the front lip of the track into the front edge of the clip Rotate the back of the track up into the clips and snap into
3. place STEP 4 Installing baton 1 Click in carriers 2 Attach baton to side or rail you wish to operate from Clip baton either into a carrier or directly into the rail STEP 5 Installing Pulley 1 Determine if cord is on the side you wish to operate Control side can be changed by pulling cord through opposite control 2 Attach cord to pulley Stretch pulley and create sufficient tension so cord remains in track Do not apply excessive tension Mark spot with pencil on wall or floor 3 Remove cords and fasten pulley to wall or floor Re install cords e THE PULLEY MUST BE INSTALLED IT IS THE LAW FAILURE TO DO SO CAN RESULT IN INJURY TO CHILDREN OR PETS 4 For center opening tracks greater than 84 click in plastic plug at center point of rail to help support cords 1 Assemble Upgrade Clips for Outside Posts 2 Attach assembled clip to Outside Posts 3 Partially assemble Upgrade Clip for Center Post 4 Mount Center Clip to Center Post and finish assembly 5 Finished result of Center Clip 6 Clips must align to be able to install track
Download Pdf Manuals
Related Search