Xantech Radio RF2IR User's Manual
Contents
1. RF2IR RF Base Station Quick Start Installation Instructions ATTENTION Requires the XTR39 to operate TEN 1 Welcome The RF2IR base station is the ultimate Xantech accessory to the Xantech XTR39 Color LCD remote It s a receiver that accepts the Radio Frequency output of the XTR39 remote and translates it into IR and RS232 command signals that can control virtually any home electronic device The RF2IR makes it simple to set up a reliable and sophisticated multi room control system that is easily controlled by the intuitive LCD touch screen control of the XTR39 RF capable remote Specifications RF Receive Frequency 2 4GHz RS232 Port Interface Tx Rx and Gnd Channel Address 16 RS232 Adapter DB9 Male to Stereo 3 5mm Plug Network ID 256 per Channel Address IR Blaster Range 30 Unit Size 5 0 x 4 75 x 1 0 IR Format Support XIR1 and XIR2 Library Unit Weight 4 0 oz Addressable Emitter Output Ports 4 Unit Color Black with silver logo Power Requirements 12Volts DC 300mA RoHS Compliant Default Network ID 1 Default RS232 Settings 9600 BAUD 8 DATA BITS 1 STOP BIT NO PARITY RF2IR Diagram Rear RS232 Port 4 Routable IR Emitter Output Power Supply RF2IR Diagram Front IR LED RF LED IR LED RF LED Flashes when emitting IR and RS232 commands Quick Start Instructions Step 1 Plug the 4 283M emitters included into the port labeled IR output 1 thru 4 on the back of the RF2IR Next pla2. RF exposure requirements and void bidaiant Raia OSSDEORBA user s authority to operate the device Xantech Limited Warranty Effective for products sold after July 1 2006 Xantech Corporation Xantech warrants to the holder of a valid proof of purchase as the first end user purchaser You its products to be free from defects in materials and workmanship for the periods specified below from the date of purchase This limited warranty extends only to You for product purchased and used in the United States of America For product purchased outside of the United States of America the terms of this warranty apply EXCEPT that You must contact the Xantech authorized distributor in your region for warranty services Product is not intended for end user installation If within the applicable warranty period above You discover such item was not as warranted above and You promptly notify Xantech in writing Xantech shall repair or replace the items at its option Xantech may elect which remedy or combination of remedies to provide in its sole discretion Xantech may use functionally equivalent reconditioned refurbished pre owned or new products or parts under this limited warranty This warranty shall not apply a to product which shall have been installed by other than an authorized Xantech installer b to installed product which is not installed to Xantech s specifications c to product which shall have been repaired or altered by oth
3. a height greater than 3 feet above the floor The ideal height should be level to the XTR39 transmitter e Avoid placing the RF2IR near comers of a room e Avoid placing the RF2IR next to microwave ovens Care and Maintenance Clean the outside of the plastic housing using a soft cloth Use warm water and mild soap solution Do not use abrasive cleaners FCC NOTICE Section 15 19 Labeling requirements This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 0197 2 This device must accept any interference received including interference that may cause undesired operation RF2IR RF Base Station Quick Start Installation Instructions Section 15 21 Information to user 2006 Xantech Corporation The changes or modifications nat expressly approved by the party responsible for compliance could void the user s authority to operate the This document is copyright protected No part of this manual may be equipment copied or reproduced in any form without prior written consent from Xantech Corporation IMPORTANT NOTE To comply with the FCC RF exposure compliance requirements no change to the Xantech Corporation shall not be liable for operational technical or antenna or the device is permitted Any change to the editorial errorsiomissions made in this document antenna or the device could result in the device exceeding the
4. ce the associated 283M emitter head directly over the IR eye on the proper source component to be controlled Step 2 Plug the RS232 Adapter Cable if required into the RF2IR port labeled RS232 Next connect the DB9 plug to the source component to be controlled In some instances a null modem converter may be required Below is a pin out of the RS232 Adapter Cable Pin 2 Rx Pin 3 Tx Hi Pin 5 Gnd Step 3 Plug the power supply into the RF2IR port labeled 12VDC The IR and RF LEDs will illuminate for 10 seconds This is part of the start up sequence After the LEDs turn off the RF2IR is ready to be used Step 4 Follow the XTR39 Instructions RF2IR Addendum and follow the steps to setup the XTR39 RF2IR Configuration Channel Address The Channel Address on the RF2IR cannot be programmed using Universal Dragon Located on the bottom of the RF2IR device is a rotary switch Turn this switch to select the desired Channel Address The switch is labeled in HEX notation A stands for Channel Address 10 B stands for Channel Address 11 The Channel Address increments with the alphabet until it ends at F which is 15 CHANNEL ADDRES Locating the RF2IR Thanks to Xantech s superior antenna design the RF2IR can be placed in several locations Key Location Points e The RF2IR should be placed on a flat stable surface e For optimal performance the RF2IR should be placed at
5. ers than Xantech d to charges for installation or set up or adjustment of customer controls e to product that has suffered normal cosmetic deterioration 1 to product which shall have been subjected to negligence misuse abuse accident or damage by circumstances beyond Xantech s control including but not limited to lightning flood electrical surge tomado earthquake or any other catastrophic events beyond Xantech s control or g to product which shall have been subjected to improper operation connected equipment failure or malfunction inadequate packing or shipping damage maintenance or storage or to other than normal use of service The foregoing warranties do not cover reimbursement for labor transportation shipping removal installation or other expenses which may be incurred in connection with repair or replacement All claims for product shipping damage must be processes within 3 days of receipt by You A Xantech Return Authorization RA must be obtained from Xantech by You your installer or your distributor for Product covered under this warranty Covered product must be sent to Xantech together with proof of purchase RA number prepaid and insured to Xantech Freight collect shipments will be refused Risk of loss or damage in transit is borne by the sender Xantech s warranty does not cover Products which have been received improperly packaged altered or physically damaged Products will be inspected upon receipt E
6. onents 1 year Limited imited j Volume Controls and Speaker Selectors 5 year Limited j J 1 year
7. xcept as may be expressly provided and authorized in writing by Xantech Xantech shall not be subject to any other obligations or liabilities whatsoever with respect to equipment manufactured or sold by Xantech or services rendered by Xantech THE FOREGOING WARRANTIES ARE EXCLUSIVE AND IN LIEU OF ALL OTHER EXPRESSED AND IMPLIED WARRANTIES INCLUDING BUT NOT LIMITED TO IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ATTENTION TO OUR VALUED CONSUMERS To insure that consumers obtain quality pre sale and after sale support and service Xantech products are sold exclusively through authorized dealers and authorized distributors Xantech products are not sold online The warranties on Xantech products are NOT VALID if the products have been purchased from an unauthorized distributor or an online E tailer In order to determine if your Xantech re seller is authorized please call Xantech 800 843 5465 WARRANTY DURATION Limited Lifetime Limited Lifetime Limited Lifetime Limited Lifetime XANTECH PRODUCT go to Xantech comiwarranty for model numbers IR Receivers and IR Emitters AIV distribution and Control Remote Control Switchers Modules and Connecting Blocks Accessories Limited Lifetime Speakers Limited Lifetime MFC BX ZPR and Commercial Products 2 year Limited Amplifiers 2 year Limited Control Interfaces Hand Held Remote Controls SPLCD Product Source Comp
Download Pdf Manuals
Related Search