Power Acoustik PEQ-86BC User's Manual
Contents
1. gt 500B DIMENS anne 178x 25 x 150 mm MIT 750 grams CONSUMPTION 5A POWER UPP 11 16V DC negative ground Due to our continuing efforts towards products improvement the above specification are subject to change without notice2. Power Acoust MODEL PEQ 86BC 7 BAND HIGH POWERED GRAPHIC EQUALIZER WITH SUBWOOFER ELECTRONIC CROSSOVER 7 BANDA GRAFICO DE ALTA POTENCIA EQUALIZADOR AMPLIFICADOR CON SUBWOOFER Y CROSSOVER ELCTRICO OWNER S MANUAL MANUAL DE INSTRUCCIONES ENGLISH INTRODUCTION The Power Acoustik Model PEQ 86BC is intended for those who value the acoustic benefits of a multi band Graphic Equalizer but who also desire higher audio power level capabilities than can be obtained in an in dash unit H contain stereo power amplifiers to drive speakers directly and 1 subwoofer pair with crossovers and sensitivity control Subwoofer output can be connected to remote high power amplifiers The seven center frequencies are concentrated in the critical 40Hz to 15KHZ region where compensation is most needed E FEATURES AND OPERATING CONTROLS SUPER AASS 8 OVER Bt ery Cain 1 FADER Allows front to rear balancing in four speaker systems for best directional imaging 2 MASTER VOLUME Simultaneously raises and lowers the volume of all output signal 3 POWER SWITCH Press into switch on the unit And press it again at outer position to switch off the unit 4 OUTPUT LEVEL DISPLAY These LED indicators show approximate power of output for both the left and right channels 5 SUBWOOFER GAIN CONTROL Allows user to adjust subwoofer output to match overall system output 6 SUBWOOFER SWITCH When the subwoofer is connected use t
3. to 12 dB 12 COMPACT DISC IN PUT JACK Using 3 5mm jack and cable plugging into CD in pul jack from any external portable player will automatically cut off the low level input and transmits the CD signal to the outlet 14 PHASE SHIFT SELECTOR SWITCH Use this switch to select Output Phase for the Subwoofer Channel to provide best time alignment and stereo imaging 14 CD INPUT GAIN CONTROL Use this control lo adjust the inpul signal from CD RCA jacks to match your 2 Sources units INSTALLATION The PEQ 86BC is designed forin dash installation directly above or below 8 standard DIN sized radio tape player Installation Kits for the purpose are available from a variety of suppliers Consult with a professional Autosound installer for assistance Each wire is individually labeled to reduce any chance oferror Phono cable pairs with plugs on both ends are required to connect the PEQ 86BC SUB WOOFER outputs tothe remote amplifiers and also for the phono inputs ifused These can be purchased froma local audio dealerinthe correctlengths for your particular installation The Black wire labeled Power Ground is connected directly to the vehicle chassis The Red wire with in line fuse is the main power input to the PEQ 86BC It should be connected toa source of Switched 12 volts Cul off by the Ignition switch This is normally the same fuse panel terminal that powers your radio The final step inthe electrical installation is to connect th
4. e Left amp Right Output signals from yourradio tothe PEQ 86BC inputs in one of two ways depending on how your radio is equipped Ifi has Phono style Line Outputs then they are connected to the matching Line inputs using a purchased cable pairas discussed above E INPUT CONNECTION Connection Wilh Speaker Inputs Connection With Speaker Inputs Connection With RCA Inputs Common Ground Floating Ground 12V 12V RCA Input CD RCA Input Red L White Right Left Black Vehicle Ground Black Vehicle Ground E OUTPUT CONNECTION 12V Red Vehicle Ground Amplified Outputs to Front and Rear Speakers Green Red Green 5 J i Grey Red IF Front ole LS Brown Red Y a E Brown i White Red S as R White Black gt ice Sub Ground Fr RCA Amp Note Use either RCA low level or SPEAKER high level inputs NEVER connect both high and low level inputs SPECIFICATIONS CONTROL ERE QUENG Ys estdcanacuaepencmvedes 40H2z 150Hz 400Hz 1KAz 3 5KHz 8KHz AND 15KHz BOCCONTROLARANGE activities euoiduaawtne te BOOST 12dB 3dB CUT 12dB 3dB INP OT SINGAL VOLTAGE eis Beech SV High 500mV Low FREQUENGY RESPONSE uinnvidde 20Hz 20KHz DISTORTO EEE owed shes lt 0 01 SUBWOOFER FREQUENCY POINT ci ce ded wigs 80Hz 120Hz SUB tna ha 12dB 3dB EE gt 600B CHANNEL SJEF
5. his switch to aclivate deactivate the subwoofer 7 SUBWOOFER CROSSOVER POINTS Two operating modes The SUBWOOFER MODE activates an internal low pass filter so only the deepest bass notes are passed to the woofer system Two position 80Hz or 120Hz 8 MUTE SWITCH Switch the knob to on position The whole music system will become silence And switch again to disengage this setting 1 9 1NPUT SELECTOR Selects Line 1 or Line 2 This can be used to switch an additional components beyond the input capabilities of your head unit For example if you wish to add a DVD or CD changer to your system you can input the signal into the CD RCA jacks located in the rear of the PEQ 86BC and select the input source via the front panel switch The top of the PEQ 86BC chassis features stereo Input Gain adjustments for the CD input See 14 in Figure 1 so that you can match the input signal of your 2 source units to match in volume when you switch between them 10 EQ Press in to engage the equalizer circuitry Press it outer position the result is the same as setting all slide controls to center position tis useful in judging the result of your EQ Settings 11 EQ SLIDE CONTROLS Each slide controls the amount of boost or cut in one small part of the total audio frequency range With all of the slides in the center positon the overall frequency response is flat By moving any slide up or down the outpul within the band ts increased or decreased by up
Download Pdf Manuals
Related Search