Brunton Bantam 81-100726 User's Manual
Contents
1. BRUNTON BANTAN Instructions for 81 100726 Use outdoors only and do not allow children to reach Please read understand and follow all instructions and warnings before using this product The proper fuel bottle for this product is included BRUNTON www brunton com Before using the Brunton Bantam stove please read and follow all the steps below carefully 1 Fino tre ruer potre 1 Pour the fuel up to the fill line on the bottle Do not overfill 2 Insert pump and turn clockwise to tighten 3 Before pumping pressure into the fuel bottle ensure that the control valve for the stove unit is set to the OFF position Pump the handle on the pump set to pressurize the fuel bottle 20 strokes NOTE Less fuel in the bottle needs more pumping strokes to pressurize the bottle N WARNING e Keep away from children To avoid the possibility of serious injury use only a Brunton pump and bottle Gog Use only White Gasoline other fuel could clog the nozzle and may cause a fire hazard OPERATING IN TIONS Ae C2 ED 1 Unfold the stove legs and place the stove on a flat surface 2 After connecting the flexible hose to the pump ensure that the fuel bottle is placed on a flat surface A WARNING Using the stove on uneven surface is very dangerous and may cause a fire hazard and serious injury When the fuel bottle has been connected to the pump be2. sure that the valve knob is set to the OFF position e When the stove is in use keep fuel bottle as far away as possible q 3 Preheating the stove Before using the stove with white gas it is necessary to pre heat the fuel This is called priming the stove 1 Turn the valve knob counter clockwise to the ON position and wait 1 2 seconds until the jet emits a small amount of fuel onto the priming pad then close the valve by rotating the knob counter clockwise to the OFF Position If fuel does not flow the fuel bottle is low on gas and the bottle may need preasurizing or more fuel e Before igniting the stove ensure that the valve knob is turned to the clockwise OFF position Never place your head or body above the stove when lighting it 2 After fuel has been primed to the stove ignite the fuel through the ignition port with a lighter or a match to preheat the generator pipe 3 After pre heating 1 2minutes slowly open the valve to allow fuel to flow through the generator unit The flame may appear yellow for the first minute of operation but should settle to a crisp blue flame that is the normal cooking flame If an excessively high yellow flame is evident turn off the stove and repeat the preheating process 4 Never allow fuel to overflow from the stove base as leaking fuel will ignite and may cause a fire hazard and serious injury 5 If the flame decreases in intensity further pressurization of the fuel bot
3. bolt Nw air spring Stove parts head oil plate leg B cS S oan iS guide spring wave washer ESS guide fab venturi nozzle pump knob filter nozzle eee nozzle Ais cap body nut heating pipe heating pipe connect bolt pane nozzle A connect nut ie connect pipe bolt gt hose pipe bushing aa AN WARNING hose washer nozzle body valve lt E connect valve connect bolt e After disassembling and assembling be sure to check for leakage with soapy water q 2 Poor performance amp nozzle clogging Colgging inside the nozzle or generator tube may disturb the fuel and create poor stove performance Remove clogging inside the nozzle hole with a nozzle pin If clogging persists inside of the nozzle or generator tube a more thorough cleaning is required A How to clean with nozzle pin 1 Turn off the stove valve and wait until the stove has completely cooled down 2 Remove the Jet by disassembling and removing the generator tube assembly from the stove with the tool kit 3 Clean the jet with the nozzle pin 4 Re Assemble the stove and check for any fuel leaks If cleaning the Jet does not improve the stove efficiency clean the generator tube as well B How to clean the generator tube 1 Begin by removing the generator tube assembly from the stove with the tool kit 2 Pull the wire out brush clean of any debris and replace 3 Re Assemble th
4. days with proof of purchase for warranty to be valid BRUNTON ATTN WARRANTY DEPT 2255 BRUNTON COURT RIVERTON WYOMING 82501 307 857 4700 NAME ADDRESS CITY ST PROV ZIP PHONE EMAIL MODEL DATE PURCHASED PURCHASED FROM CITY ST PROV ZIP PRICE PAID 1008 BRUNTON
5. e stove and check for any fuel leaks WARRANTY Brunton warrants this product to be free of defects in workmanship and materials for the lifetime of the original owner and is nontransferable If you have any problems with your Brunton stove the stove should be returned to the dealer or sent to Brunton 2255 Brunton Court Riverton WY 82501 U S A Please contact Brunton at the number below to obtain RA Clean food and soot from stove before shipping Shipping cost to Brunton is the responsibility of the purchaser Return postage will be paid by Brunton Please return this warranty card to Brunton as a proof of purchase This warranty does not cover damage caused by accident misuse abuse or tampering A nominal charge will be assessed to repair such damage BRUNTON www brunton com 2255 Brunton Court Riverton WY USA 82501 PH 307 857 4700 LIMITS OF LIABILITY Brunton assumes no responsibility for any inconvenience loss or injury direct or consequential damage arising from possession or use of the goods This warranty gives you specific legal rights which may vary from state to state Check with your local state about your rights N WARNING Only use in well ventilated areas Keep well away from children Do not leave unattended while in use Do not operate near flammable materials BRUNTON VISIT OUR WEBSITE AT www brunton com Warranty card must be filled out completely and returned within 30
6. tle is required Turn slowly counter clockwise after preheating Preheating d 4 Extinguishing the stove 1 To extinguish the stove turn the valve knob to the OFF position and flip the bottle over NOTE The stove will continue to burn for a short time until all of the fuel in the generator tube and fuel hose is consumed Flip C m Small flame remains for 2 3 minutes consuming all the fuel in the hose 2 After the fire extinguishes the stove will remain hot wait until the stove cools down 3 Separate the stove from pump 4 Fuel bottle and pump can be transported as a connected assembly When separating the pump from fuel bottle turn the pump slowly so that the pressure retained inside the fuel bottle can release gradually a Hissing _ aa Inner pressure exclusion Separation PARTS REPLACEMENT AND MAINTENANCE 1 Dried or torn parts need to be replaced Check the color and size and any printed markings and contact your nearest Brunton stock list or retailer for replacements Oil seals Oil Nozzle Tool kit Checking amp replacing seals and 0 rings pump knob pipe bolt Pump parts zo guide spring guide packing washer guide washer packing holder ag packing rubber i connect bushing setting bushing spindle head assembly g setting bolt housing cap housing i knob nylon hose A o rings pipe filter Soris A air bushing body o ring air bushing air
Download Pdf Manuals
Related Search