Siig Hi-Speed USB Dual-Port PCI
Contents
1. Devices with yellow exclaimation marks remove them and restart your system Refer to software installation section to re install the driver If there s no USB controller under Other Devices shut down your system remove the board and re insert it in the same or a different PCI slot Make sure the board is properly seated in the PCI slot Boot up your system and refer to software installation section to re install the driver Technical Support QUESTIONS SIIG s Online Support has the answers Simply visit our web site at www siig comand click SUPPORT Our online support database is updated daily with new drivers and solutions The answers to your problems could be just a few clicks away Return Merchandise Authorization RMA SIIG warrants to the original buyer of the product that the hardware is free of defects in materials and workmanship for a period of one two or five years from the date of purchase If your product fails to be in good working order during the warranty period you may return it to SHG for repair or replacement at SIIG s option To return the product you need to follow these steps Step 1 Contact SIIG s RMA Department To obtain an RMA number SIIG s RMA Department can be reached by phone at 510 413 5333 or fax at 510 657 5962 or email at service siig com In order to issue an RMA number the product serial number is required This number can be found on the side of the box and on the back of the pro2. AA USB 2 0 PCI Quick Installation Guide Introducing the USB 2 0 PCI The USB 2 0 PCI adds high speed USB 2 0 interface to your system It supports high speed 480 Mbps full speed 12 Mbps and low speed 1 5 Mbps data transfer modes With USB 1 1 backward support this host adapter works with various types of USB 2 0 1 1 devices including hubs digital cameras PC video cameras scanners joysticks and more Note USB 1 1 devices are limited to USB 1 1 speeds even when they are connected to USB 2 0 host adapter or USB 2 0 hubs Features and Benefits e Compliant with USB specifications revision 2 0 e Conforms to PCI Specifications e Supports simultaneous operation of multiple high speed USB 2 0 and USB 1 1 devices e Users friendly hot swapping feature allows you to attach remove USB devices without turning your system off e Supports 480 Mbps 12 Mbps and 1 5 Mbps data transfer modes e Works with a variety of USB2 0 USB 1 1 devices including hubs data storage devices PC video cameras digital cameras CD R RWs DVD ROMs scanners printers memory card readers CF SM SD MMC Memory Stick and more System Requirements e Pentium class computer with an available PCI slot e Windows 98SE ME 2000 XP Package Contents e One USB 2 0 PCI e Driver diskette e This quick installation guide 04 0293A 1 Hardware Installation General instructions for installing the card are provided below Refer to your computer s refe
3. I US22xx FCC RULES TESTED TO COMPLY WITH FCC PART 15 CLASS B OPERATING ENVIRONMENT FOR HOME OR OFFICE USE FCC COMPLIANCE STATEMENT This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation THE PARTY RESPONSIBLE FOR PRODUCT COMPLIANCE SIG Inc 6078 Stewart Ave Fremont CA 94538 3152 USB 2 0 PCI is a trademark of SHG Inc SIG and SIIG logo are registered trademarks of SIIG Inc Microsoft and Windows are registered trademarks of Microsoft Corporation Pentiumisa registered trademark of Intel Corporation Other names used in publication are for identification only and may be trademarks of their respective companies October 2002 Copyright 2002 by SIIG Inc All rights reserved Empty Page
4. ard click Next Choose Search for the best driver for your device click Next Clear all check boxes click Next and Next again Click Next then Finish Repeat steps 5 8 one more time when the second USB 1 1 host is detected 10 Windows now detects the USB 2 0 host and loads it s driver 11 The board is now ready for use Windows ME Driver Installation 1 After installing the board boot up to Windows At the Add New Hardware Wizard click Cancel Click Start Run insert the driver diskette type A setup206 exe then click OK Give it a few seconds for driver installation to complete Remove the driver diskette then click Close to restart On the restart Windows installs the driver automatically 5 The board is now ready for use Windows 2000 Driver Installation 1 After installing the board boot up to Windows At the Found New Hardware Wizard click Cancel Click Start Run insert the driver diskette type A setup206 exe then click OK Give it a few seconds for driver installation to complete Remove the driver diskette then click Close to restart On the restart Windows installs the driver automatically 5 The board is now ready for use Windows XP Driver Installation If you have have XP Service Pack 1 or later installed Windows will automatically detect and install the correct driver for this board Otherwise follow all steps below 1 After installing the board boot up t
5. duct Step 2 Complete the RMA form e Fill out your Return Merchandise Authorization RMA form and include it in the package with the product e Properly pack the product for shipping All software cable s and other accessories that came with the original package must be included e Clearly write your RMA number on the top of the returned package and on the accompanying RMA form SIIG will refuse to accept any shipping package and will not be responsible fora product returned without an RMA number posted on the outside of the shipping carton Step 3 Ship the Product You are responsible for the cost of shipping back to SIIG at the following address SIIG Inc RMA 6078 Stewart Ave Fremont CA 94538 SIIG will ship the repaired or replaced product via UPS Ground or US Mail at no cost to you 6 UK Warranty amp Support Information The 5 year warranty supplied with this product is offered by SIIG Inc If you should happen to encounter any problems with this product please follow the procedures below 1 If itis within the first year of purchase please return product to the outlet you purchased from 2 If your product is between 2 and 5 years old from date of purchase please contact SIIG using the contact details below For UK Technical Support Telephone 44 0 1255 687503 Fax 44 0 1255 687501 Email support siig uk com Website http www siig uk com PRODUCT NAME MODEL NUMBER USB 2 0 PC
6. o Windows At the Found New Hardware Wizard click Cancel Click Start Run insert the driver diskette type A setup206 exe then click OK At the Software Installation window click Continue Anyway Our driver has been thoroughly tested in Windows for stability This message appears because Microsoft has not tested this product through WHQL certification 4 Click Close to restart and remove the driver diskette 8 9 At the Found New Hardware Wizard select Install the software automatically Recommended then click Next At the Hardware Installation window click Continue anway then click Finish Windows now detects the USB 2 0 Hub and prompts you to load it s driver Repeat steps 5 and 6 The board is now ready for use To verify successful driver installation 1 Check Device Manager to verify successful driver installation Windows 98SE ME From the main desktop right click My Computer then click Properties Click Device Manager tab Windows 2000 XP Right click My Computer then click Manage Click Device Manager Double click Universal Serial Bus controllers and the following options should be displayed in addition to others that may come with your system NEC USB Open Host Controller NEC USB Open Host Controller NEC USB Enhanced Host Controller USB 2 0 Root Hub Device USB Root Hub USB Root Hub If these options DO NOT appear a Look for USB controller s under Other
7. rence manual for further information if needed 1 Turn OFF the power to your computer 2 Unplug the power cord and remove your computer s cover 3 Remove the slot bracket from an available PCI slot 4 Carefully align the card to the selected PCI slot and push the board down firmly but gently until it is well seated gl Replace the slot bracket s holding screw to secure the card 6 Replace the computer cover and reconnect the power cord Figure 1 Inserting PCI Board Software Installation The USB 2 0 PCI has three built in USB hosts Two hosts handle USB 1 1 devices and the third host handles USB 2 0 devices USB 1 1 and USB 2 0 devices are automatically routed to the correct USB hosts Please follow instructions below to install drivers Note Throughout the driver installation you may be prompted to insert your Windows Installation CD Some files on this CD are neccessary to complete the installation Please insert the CD when prompted and follow the on screen instructions Windows 98SE Driver Installation 1 NO 08 SD ASA O After installing the board boot up to Windows At the Add New Hardware Wizard click Cancel three times Click Start Run insert the driver diskette type A setup206 exe then click OK Give it a few seconds for driver installation to complete Remove the driver diskette then click Close to restart When Windows restarts a USB 1 1 host is detected At the Add New Hardware Wiz
Download Pdf Manuals
Related Search