Primera Technology DX850 Label Maker User Manual
Contents
1. Figure 2 6 In order to feed the label stock between the rollers the Liner Idler Roller should be in the unclamped position See Figure 2 10 for a detailed diagram of the Liner Idler Roller positions Figure 2 6 Note This procedure assumes that the first 6 inches of labels will not be dispensed using the Label Dispenser Of course you may still peel these labels by hand 6 DX850 Label Dispenser 9 Pull the stock through until the Peel Edge is positioned in between two of the labels Figure 2 7 Figure 2 7 Note The liner may be fed out the front or back of the Label Dispenser 10 Push the Liner Idler Roller into the clamped position by pressing your thumbs on the Liner Idler Roller Tabs on both sides Figure 2 8 Figure 2 8 DX850 Label Dispenser 7 11 Move the Label Sensor Bracket where desired within the width of the label Figure 2 9 Figure 2 9 12 You are now ready to dispense labels 8 DX850 Label Dispenser Section 3 Dispensing the Label To dispense a label first load label stock as described in Section 2 connect power and switch on the Label Dispenser Follow these steps to dispense labels 1 Before you start dispensing you should adjust the Label Sensor on the Label Sensor Bracket so that the distance between the Label Sensor and the Peel Edge is equal to roughly 1 2 less than the label height Figure 3 1 Figure 3 1 For example for a 4 wide x 22. Start Stop Button Starts or stops the motor depending on whether or not the label sensor is tripped Note If sensor does not get triggered in a 24 run the motor will stop a Ifthe motor is in Stop Mode the display flashes Otherwise the display is on Counter solid Reset b If held for 2 seconds it will toggle the label counter between Decrement and Increment Mode as indicated by the lower right decimal point If the decimal point is on the label counter is in Decrement Mode Counter Reset Button Pressing this button will reset the label counter if held for 2 seconds Button Pressing this button for 2 seconds will increase the label counter It will repeat advance if held Button Pressing this button for 2 seconds will decrease the label counter It will repeat advance if held Special Setup Modes 1 To set the LED Display Intensity Press and hold the Start Stop Button and the Button until the display changes to LED Then press the or buttons to adjust the LED intensity 2 Half Speed Mode To start system in Half Speed Mode for wide label stock Press and hold the Button during power up DX850 Label Dispenser 11 Section 5 Label Path Diagram Label Path Diagram Label Path Liner Drive Roller Liner Idler Roller Peel Edge Front or Rear Liner Output 12 DX850 Label Dispenser Section 6 Troubleshooting and Maintenance Troubleshooting Motor stalling on labels 6 152 mm
3. 0 75 to 8 25 19 1mm to 209 6mm 1 00 to 8 38 25 4mm to 213 0mm 0 75 to 24 00 19 1mm to 609 6mm 2 to 3 51 8mm to 76 2mm ID 12 VDC 5 0 A 100 240 VAC 50 60 Hz 60 watts 4 in sec in Default Mode 2 in sec in Half speed Mode for 6 8 wide labels See Section 4 UL UL C CE FCC Class B 11 5 lbs 5 2 kg 13 44 W x 8 75 Hx 11 25 D 341mm W x 222mm H x 2876mm D P N 511260 052609
4. high 101 6mm x 50 8mm label you would set this distance to approximately 1 1 2 38 1 mm The exact distance is not critical It is only important that you set the distance so that the label does not come off the liner when presented If the label height dictates the sensor be moved beyond the available travel set the sensor to the minimum or maximum position as applicable 2 To Start dispensing press the Start Stop button on the Control Panel Figure 3 2 Figure 3 2 Mi Li Start Counter Stop Reset DX850 Label Dispenser 9 3 A label will peel off the liner until it trips the Label Sensor Figure 3 3 Figure 3 3 4 Pull the label off the liner with a quick upward motion Figure 3 4 Figure 3 4 Note For labels higher than 3 76 2 mm you will have to slowly pull up on the label with continuous force until the end of the label clears the Guide Roller For these type of labels set the label sensor bar to the maximum distance from the Peel Edge 5 When you are ready to stop dispensing labels or if you want to stop for another reason such as adjusting the label sensor position simply press the Start Stop Button 6 To remove the label stock disengage the Liner Idler Roller by pulling back on the tabs 10 DX850 Label Dispenser Section 4 Using the Control Panel The Control Panel can be used to start and stop dispensing of labels display label counts and other advanced functions
5. or wider For label stock 6 152 mm and wider it may be necessary to reduce the speed of the Label Dispenser The Label Dispenser includes a Half Speed Mode that generates more power from the motor for wider label stock To activate this mode hold down the Button while switching on the unit The Label Dispenser will revert back to the Default Mode when switched on without holding down the Button Maintenance Unclamp Liner Idler Roller When not in use leave the Liner Idler Roller in the unclamped position This will minimize the possibility that permanent indentations will be made in the Liner Drive Roller Lubricate bearings Primera recommends oiling the four bearings associated with the Liner Drive Roller and Liner Idler Roller Oil these four bearings for every 50 000 labels dispensed They should only be oiled after the first 50 000 labels as they are lubricated with a special grease at the factory One drop of any machine oil or motor oil for each bearing should be adequate This maintenance is optional but will increase the life of the Label Dispenser for heavy users who use the Label Dispenser for several hours each day DX850 Label Dispenser 13 Section 7 Specifications Supply roll diameter Label width Media liner width Label height length Supply roll core Electrical rating Power requirements Feed speed Agency certifications Weight Dimensions 14 DX850 Label Dispenser Up to 8 203mm
6. DXS50 LABEL DISPENSER PRIMERA O 2009 All rights reserved Unpacking and Setup Loading the Label Stock Dispensing the Label Using the Control Panel Label Path Diagram Troubleshooting and Maintenance Specifications 11 12 13 14 Notices The information in this document is subject to change without notice NO WARRANTY OF ANY KIND IS MADE WITH REGARD TO THIS MATERIAL INCLUDING BUT NOT LIMITED TO THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE No liability is assumed for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material This document contains proprietary information that is protected by copyright All rights are reserved No part of this document may be photocopied reproduced or translated into another language without prior written consent Trademark Acknowledgments Windows is a registered trademark of Microsoft Corporation All other trademarks are the property of their respective owners Printing History Edition 1 0 052609 Copyright 2009 All rights reserved FCC Compliance Statement This device complies with part 15 of the FCC rules Operation is subject to the following two conditions 1 this device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation For Users in the United States Thi
7. H THE CLOTHING WHILE THE LABELS ARE BEING APPLIED Section 1 Unpacking and Setup Thank you for purchasing the DX850 Label Dispenser hereafter referred to as Label Dispenser The Label Dispenser includes a Power Cord 12 volt Power Adapter and the parts shown in Figure 1 1 The Roll Bar Roll Guides and Roll Drag Arm are located in the supply box along with the Power Cord You will need to assemble them as shown in Figure 1 1 and 1 2 Also see Section 2 for more detailed instructions on assembling these parts Attach the Power Cord and switch on the power as shown in Figure 1 2 Finally remove the foam insert between the Liner Idler Roller and Liner Drive Roller Figure 1 1 Guide Roller Label Sensor Roll Guides Liner Drive Roller Roll Bar Liner Idler Roller Control Panel Label Sensor Bracket Peel Edge Figure 1 2 Power Adapter Roll Guides Roll Bar Roll Drag Arm Power Switch Power Input 12V DX850 Label Dispenser 3 Section 2 Loading the Label Stock 1 Remove the Roll Bar and Roll Guides from the Label Dispenser The Roll Guides and Roll Drag Arm are removable and adjustable They are held in place magnetically Figure 2 1 Figure 2 1 2 Remove one Roll Guide and the Roll Drag Arm from the Roll Bar 3 Place the label stock roll on the Roll Bar with one side against the upright of the remaining roll guide Place it on the Roll Bar with the lo
8. ity to operate and or obtain warranty service for this equipment For Users in Canada This digital apparatus does not exceed the Class A limits for radio noise for digital apparatus set out on the Radio Interference Regulations of the Canadian Department of Communications Le present appareil numerique n emet pas de bruits radioelectriques depassant les limites applicables aux appareils numeriques de la class A prescrites dans le Reglement sur le brouillage radioelectrique edicte par le ministere des Communications du Canada General Safety Information Note Notes are used to notify of installation operation or maintenance information that is important but not safety related Caution Caution is used to indicate the presence of a hazard which if ignored may result in damage to the unit Warning Warning means that a potential safety hazard exists and indicates procedures that must be followed exactly to avoid serious personal injury A WARNING TO PREVENT FIRE OR SHOCK HAZARD DO NOT EXPOSE THE UNIT TO RAIN OR MOISTURE TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE EXTERIOR PANELS NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL OPERATE THE UNIT WITH ONLY THE PROPER ELECTRICAL SPECIFICATIONS AS LABELED ON THE PRINTER AND AC ADAPTER A WARNING DO NOT WEAR LOOSE FITTING CLOTHING SUCH AS NECK TIES OR LOOSE LONG SLEEVES WHEN OPERATING THE DX850 THE MOTOR IS VERY POWERFUL AND THE LINER DRIVE ROLLER COULD CATC
9. ose end of the stock feeding off the top of the roll Figure 2 2 Figure 2 2 Tip For smaller diameter label roll cores you may need to reverse the Roll Guides so that the bottom of the guides are facing out to allow the uprights to be placed next to the roll 4 DX850 Label Dispenser 4 Place the Roll Drag Arm under the Roll Bar The Roll Drag Arm may be placed on either side of the Roll Bar but the rounded tip of the Roll Drag Arm should be located in the center of the inside of the core The arm is spring loaded so that there is downward pressure on the inside of the roll This helps prevent application alignment problems near the end of a roll Figure 2 3 Figure 2 3 5 Place the removed Roll Guide back on the Roll Bar and slide it close to but not touching the label stock roll Figure 2 4 Figure 2 4 Tip Roll Guide Uprights must not pinch the label stock roll The label stock roll must have free play between guides DX850 Label Dispenser 5 6 Now position the stock to correspond with the general area where the labels will be dispensed 7 Pull the loose end of the label stock forward under the Top Roller Pull approximately 6 inches of label stock out beyond the Peel Edge Figure 2 5 Figure 2 5 Tip See Section 5 for a Label Path diagram 8 Take the loose label stock and feed it between the Liner Idler Roller and the Liner Drive Roller
10. s product is intended to be supplied by a UL listed Direct Plug In Power Supply marked Class 2 or a UL listed ITE Power Supply marked LPS with output rated 12VDC 4 5A or higher This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Re orient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technician for help Use of shielded cables is required to comply with the Class A limits of Part 15 of the FCC Rules You are cautioned that any changes or modifications not expressly approved in this manual could void your author
Download Pdf Manuals
Related Search