User`s Manual U User`s Manual
Contents
1. D OO If you don t want to use the upper cutlery basket pull it back to yourself to remove it from the machine rotate the rail lids towards outside and pull them towards yourself to take them out B In order to replace the upper cutlery basket into its place again repeat the same process in reverse order 20 39 EN Dishwasher User s Manual Preparation Cutlery basket Cutlery basket is designed to wash your dishes such as knife fork spoon etc in an efficient manner Since the cutlery basket can be moved A B you can create more space while placing your dishes in the lower basket and free up space for your dishes of different sizes Adjusting the height of the upper basket Basket adjustment mechanism on the loaded upper basket of the machine Is designed to allow you create taller areas in the upper or lower section of the machine based on your requirements by adjusting the height of the loaded basket in up or down directions To raise the basket Grab one of the upper basket wires right or left and lift it up A Repeat the same process to raise the other Side of the basket Make sure that both sides of the loaded basket height adjustment mechanism are at the same level down or up To lower the basket Press the latch on the loaded basket adjustment mechanism right and left to lower the basket B Repeat the same process to lower the other side of the basket2. E Preparing the machine 9 Programme selection 24 Auxiliary FUNCTIONS 26 Programming the washing time 27 Starting the proqrammoe 28 Child Key LOCK 28 Cancelling the proqramme 29 Salt indicator B 29 Rinse Aid indicator 56 29 End of proqramme 29 Water cut off warning 29 Overflowing warning 29 6 MAINTENANCE AND CLEANING 30 Cleaning the outer surface of the S RUS SE R L 30 Cleaning the interior of the machine30 Cleaning the filters 5 5 30 Cleaning the hose filter 31 Cleaning the impellers 31 Lower impeller 31 1 32 Top Impeller 32 7 TROUBLESHOOTING 33 8 GUARANTEE 38 EB instructions for safety and environment This section contains safety instructions that will help to give protection from risk of personal injury or property damage Failure to follow these instructions shall void all warranties General safety Never place the product on a carpet covered floor otherwise lack of airflow beneath the product will cause electrical parts to overheat This will cause 7 vvith your product Do not operate the product if the power cable p
3. Dishwasher User s Manual 27 39 EN Operating the product Time Delay function can not be set after the programme starts G Starting the programme To start your machine after selecting the programme and auxiliary functions press Start Pause Cancel key Once the programme starts a tune is played and the estimated time remained to the end of the programme will appear on the Display Information Line Start Pause Cancel indicator starts lighting continuously water softening depending on the hardness level of the supply water Remaining time displayed towards the end in some programmes can be different from the time indicated at the beginning due to this process The total time can also change while the programme is running depending on the ambient temperature where your machine is installed temperature of the supply water and amount of the dishes ii Your machine performs Pay attention not to open the door of the machine when it is running Stop the machine by pressing Start Pause Cancel key if you have to open the door Then open the door of the machine There may bea rush of vapour when you open the door of your machine be careful Close the door of your machine and press Start Pause Cancel key again Programme The machine will remain silent in pause mode for some time in order to remove the water in the machine and on the dishes completely and to have the vvater
4. 3 2 17 will appear on the display Machine will turn off with the end melody at the end of 3 seconds Machine will turn on with economy programme in On mode and the number of the economy programme will appear on the programme Indicator In Off position indicators on the display will turn off Start Pause Cancel key t is used to start pause or cancel a selected programme or function Programme Selection keys They are used to select the washing programme you determined from the table of Programme data and average consumption values Delayed Start key It should be pressed to make the time delay settings Preparing the machine 1 Open the door of the dishwasher 2 Place the dishes in accordance with the Instructions in the user manual 3 Make sure that the upper and lower impellers rotate freely 4 Put adequate amount of detergent into the detergent dispenser 5 Check if the Salt and Rinse Aid indicators light and add salt and or rinse aid if needed 6 Close the door of the dishwasher Programme selection 1 Press the On Off button to turn on your machine 2 Refer to the table of Programme data and average consumption values to determine a washing programme Suitable for your dishes 3 Press Programme Selection keys until the number of the programme you selected appears on the Programme indicator Use P to switch to the next programme and P to switch to the previous
5. corroded item can migrate to other stainless steel surfaces and cause corrosion on those surfaces as well Such items should not be washed in dishwashers Dishwasher User s Manual 35 39 EN Troubleshooting Detergent remains in detergent dispenser e Detergent dispenser was damp when adding detergent gt gt gt Make sure that the detergent dispenser is dried well prior to filling it with detergent e Detergent is added long before the washing process gt gt gt Pay attention to add detergent shortly before start up of the washing e Opening of the detergent dispenser lid is prevented during washing gt gt gt Place the dishes in a way that will not prevent the detergent dispenser lid from opening and the water going into the machine from impellers e Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents e Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Care Decorations and ornaments on kitchen utensils are being erased i Decorated glasses and decorated lustre porcelains are not suitable for washing in the dishwasher Manufacturers of Some glassware and porcela
6. eko sz Dishvvasher DFN28R20W User s Manual Dishwasher DFN28R20W Users Manual Please read this user manual first Dear Customer We hope that you get the best results from your product which has been manufactured with high quality and state of the art technology Therefore please read this entire user manual and all other accompanying documents carefully before using the product and keep it as a reference for future use If you handover the product to someone else give the user manual as well Follow all warnings and information in the user manual Remember that this user manual is also applicable for several other models Differences between models will be identified in the manual Explanation of symbols Throughout this User Manual the following symbols are used G Packaging materials of the product are manufactured 9 from recyclable materials in accordance with our National Environment Regulations Important information or useful hints about usage Warning for hazardous Situations with regard to life and property Warning for electric shock Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material collection points designated by the local authorities CONTENTS 1 INSTRUCTIONS FOR SAFETY AND ENVIRONMENT 4 General safety 4 Intended Use yadd adana
7. Tea cafe or lipstick stains remain on dishes e Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Surface quality of the kitchen utensils is deteriorated gt gt gt Tea and cafe Stains or other dye spots may not be cleaned in dishwasher when they have penetrated in deteriorated surfaces Desired washing performance can not be obtained on kitchen utensils with deteriorated surfaces and it is not suitable to use such utensils in terms of hygiene as well It is not recommended to wash such kitchen utensils in dishwasher e Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents Lime traces remain on dishes and glassware gains a misty appearance e Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse ald If necessary Increase the rinse aid setting If there is enough amount of rinse aid in the machine e Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting e Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed af
8. material Packaging materials are dangerous to children packaging materials in a safe place away from reach of the children Packaging materials of the product are manufactured from recyclable materials Dispose of them properly and sort in accordance with recycled waste instructions Do not dispose of them with normal domestic waste Transportation of the product If you need to move the product do it in upright position and hold from the rear side Tilting the product onto its front Side may cause the electronic parts in it get wet and damaged 1 Unplug the product before transporting It 2 Remove water drainage and water supply connections 3 Drain the remaining water in the product completely Dishwasher User s Manual 5 39 EN Instructlons for safety and environment Compliance with WEEE collection points designated by Directive and Disposing the local authorities of the Waste Product This product complies with EU WEEE Directive 2012 19 EU This product Dears a Classification symbol for waste electrical and electronic equipment WEEE This product has been manufactured with a parts and materials which can be reused and are suitable for recycling Do not dispose of the waste product with normal domestic and other wastes at the end of its service life Take it to the collection center for the recycling of electrical and electronic equipment Please consu
9. EN Dishwasher User s Manual Preparation Suggestions for loading the dishwasher Improper Loading Of Dishware T MN Lower basket li ha m PULL Tag Dishwasher User s Manual 19 39 EN Preparation Upper cutlery basket The upper cutlery basket is designed for small dishes or long items that cannot fit 8 M into the lower cutlery basket FEA var Spe eee ae pa a g After taking out the basket by lifting it up remove the carrier part from the rails by pulling it towards yourself C Thanks to the easy take out from the machine feature it allows taking out the dishes from the machine together with the basket after they are washed A Since it can fit into all standard size drawers it does not require the dishes to be removed from the basket and placed into the kitchen drawers or shelves Replace the rail lids and push them back to O seat them into their places Turn the rails inside the machine sideways to seat them properly in their places D d Sees 3i eja a 2 2 Rane hg cy eae Be oe fees 4 e mym ae pang FENN BAe ees azil m4 H A yA ae oe 4
10. Make sure that both sides of the loaded basket height adjustment mechanism are at the same level down or up Dishwasher User s Manual 21 39 EN Preparation Collapsible upper basket tines Upper basket of the machine is equipped with tines with gradual folding system A that you can lay down when you need a larger space for large dishes To bring the collapsible tines into horizontal position grab the tines from mid position and push them in the directions of arrows Place your larger dishes into the area created To bring the tines back to vertical position just lift them up Collapsible tines will click into the latch again yO Bringing the tines to the horizontal position by holding them from the tips may cause them to bend Therefore it will be appropriate to bring the tines in the middle to horizontal or vertical position by holding them from their stems and pushing in the direction of arrow Collapsible lower basket tines The six piece foldable tines A located at the lower basket of the machine are designed for an easier placement of large pieces such as pans bowls etc You can create larger spaces by folding each tines individually or all of them at once To bring the collapsible tines into horizontal position grab the tines from mid position and push them in the directions of arrows B To Dring the tines back to vertical position just lift them up Co
11. consumption 1800 2100 W see rating label 1800 W see rating label Total current depends on the model 10 A see rating label Drain pump power consumption 30 W see label Mpa Technical specifications may be changed without prior notice to improve the quality of the product G Values stated on the markings of the product or in the printed documents accompanying the product are obtained in the laboratory on basis of the relevant standards Depending on operational and environmental conditions of the product these values may vary Figures in this manual are schematic and may not match the product exactly Fan drying system Fan drying system ensures efficient drying of your dishes It is normal to hear a different sound than that of washing cycle during fan operation Note for test institutions Data required for performance tests shall be provided upon request Requests can be e mailed to the following address dishwasher standardloading com Do not forget to provide the code stock and serial numbers of the product to be tested in your request e mail along with your contact information Code stock and serial numbers of the product may be found on the type label attached to the side wall of the door 8 39 EN Dishwasher User s Manual Installation To make the product ready for use make sure that the electricity tap water Supply and water drainage systems are appropriat
12. machine Since the Salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme Salty food remnants have remained on dishes for along time gt gt gt If cutlery soiled with such foods will be kept waiting in machine dirt must be removed by prewash or dishes must be washed without being kept waiting e Electric installation is not grounded gt gt gt Check if your machine is connected to the actual grounding line Otherwise the static electric created in the product causes arcs on the surfaces of metal items creating pores removing the protective cover on the Surface and Causing discoloration e Intensive cleansers such as bleaches are used gt gt gt Protective cover on metal surfaces gets damaged and looses its efficiency in time when it gets in contact with cleansers such as bleach Do not wash your dishes with bleach e Metal items particularly such as Knives are used for purposes other then their intended 4565 gt gt gt Protective cover on the edges of knives may get damaged when they are used for purposes such as opening cans Do not use metal kitchen utensils out of their intended uses e Cutlery are made of low quality stainless steel gt gt gt Corrosion on such items is inevitable they should not be washed in dishwashers e Kitchen utensils that are already corroded are washed in dishwasher gt gt gt Rust ona
13. softener cleaned and then itvvill resume runninq in drying mode G Child Key Lock You may prevent other people from interrupting and changing the programme cycle and time delay while the machine is running To activate the Child Lock 1 Pres Child Key Lock keys simultaneously and hold for 3 seconds 3 2 1 is displayed on Display Information Line and key lock is activated Child Lock prevents the selected programme or functions from being changed and disables the Start Pause Cancel key G Child Lock does not lock the door of the machine G If you turn your machine off by using On Off key at the end of the programme the Child Lock will be deactivated automatically For energy saving the product is automatically turned off following the completion of the programme or if the programme is not started will resume running To deactivate the Child Lock 1 Pres Child Key Lock keys Simultaneously and hold for 3 seconds 28 39 EN Dishwasher User s Manual Operating the product 2 3 2 1 is displayed on Display Information Line and key lock is cancelled Cancelling the programme 1 Press Start Pause Cancel key for 3 seconds to cancel the programme 2 Release the key when the Start Pause indicator starts flashing For a couple of minutes the machine vvill Tulfill the necessary operations required to cancel
14. sound is heard Do not use the dishwasher without filter G Incorrect placement of the filters will reduce washing efficiency G Cleaning the hose filter Damages on the machine that may be caused by impurities coming from the urban supply water or your own water installation such as sand dirt rust etc can be prevented by means of the filter attached to the water inlet hose Check the filter and the hose regularly and clean them if necessary 1 Turn off the tap and remove the hose 2 After taking out the filter clean it under runninq tap vvater 3 Place the cleaned filter back to its seat in the hose 4 Install the hose to tap depends on model Cleaning the impellers Clean the impellers at least once a week in order for the machine operates efficiently Lower impeller Check if the holes on the lower impeller 1 are clogged If they are clogged remove and clean the impeller Pull the lower impeller up to remove it A B Dishvvasher Users Manual 31 39 EN Maintenance and cleaning Upper impeller Top Impeller Check if the holes on the upper impeller 1 Check if the holes on the top impeller 1 are clogged If they are clogged remove of your machine are clogged If they are and clean the impeller Turn its nut to left clogged remove and clean to remove the upper impeller A B To remove them slightly 1 push them Make sure that
15. the programme There might be residues of detergent or rinse aid left in the machine and or on the pieces being washed depending on the step the programme you have cancelled was in Salt indicator S Please check the salt indicator on the display to see whether there is adequate amount of softening salt in the dishwasher or not You need to refill the salt reservoir with salt whenever salt warning Indicator appears on the display of your machine Adjusting the water hardness 1 level is explained in Water Softening System section Rinse Aid indicator Please check the rinse aid indicator on the display to see whether there is adequate amount of rinse aid in the dishwasher or not You need to refill the rinse aid reservoir with rinse ald whenever rinse aid warning indicator appears on the display of your machine End of programme End of Programme indicator will light up once the washing programme is over 1 Press the On Off button to turn off your machine 2 Close the tap 3 Unpluq the machine from the socket For energy saving the product is automatically turned off following the completion of the programme or if the programme is not started Leave your dishes in the machine for about 15 minutes to cool dovvn after they are washed Your dishes will dry in a Shorter time if you leave the door of your machine ajar during this period This process will increase the dr
16. 4 Children s safety wc 5 Disposing of packaging material 5 Transportation of the product 5 Compliance with WEEE Directive and Disposing of the Waste Product 6 Compliance with RoHS Directive 6 Package information 6 2 DISHWASHER 7 OVET VIEW ada daaa yala andan 7 Fan drying system sesers 8 Technical specifications 8 3 INSTALLATION 9 Appropriate installation location 9 Connecting water supply 9 Connection to the draln 9 Adjusting 13 25 10 Electrical connection 10 This appliance must be earthed 10 Fitting a different pluq 11 PUTAS a id 11 4 PREPARATION 12 Tips for energy savinq 12 Water softening system 12 Adjusting the water softening aydi 12 Adding Salt sesser z Water hardness amp regeneration 5105 b 13 GTC 15 Adding detergent 15 Tablet detergents 16 Rinse S 17 Upper basket height adjustable r 5770075550 18 Upper cutlery baskef 20 Cutlery basket wcrc 21 Adjusting the height of the upper Uu 21 Collapsible upper basket tines ze Collapsible lower basket tines 22 5 OPERATING THE 77
17. Adjust the Water Hardness 1 After turning on the machine press Time Delay and P P keys simultaneously After the countdown 3 2 1 is displayed keep the keys pressed for a while 2 Press P P key to activate the e position 3 Using Time Delay key adjust water hardness level according to the hardness of the supply water See Water hardness level adjustment table for correct setting 4 Press On Off key to save the setting Water Hardness Level Adjustment Table English German French Position of Hardness Water Water Water Regeneration Level Hardness Hardness Hardness Adiustment Water Hardness Level Indicator dE dF Switch 1 Level l 1 Press the Time Delay key to switch the 2 4 Level water hardness level to position 1 6 9 EE 3 Level 2 Press the Time Delay key to svvitch the 9 4 14 22 z le 4 water hardness level to position 2 2 Perform the same hardness level adjustment that you um 2 water hardness level to position 3 also with the regeneration 5 Level i adjustment switch For 2 28 34 Press the Time Delay key to switch the example if you have adjusted to 3 in the control panel 6 Level also set the regeneration Press the Time Delay key to switch the adj ustment switch to 3 99 90 vvater hardness level to position 5 r5 If the hardness level of the water that you use is above 90 dF French standard for water hardness or if yo
18. alt in water may take a couple of hours Therefore Salt Indicator remains on for awhile after adding salt into the machine Loose Salt grains can cause rust marks in your machine if not rinsed away Only fill salt just before a programme is run Detergent You can use powder or tablet detergent in the machine Only use in the machine the detergents produced particularly for use with dishwashers We recommend you not to use detergents that contain chlorine and phosphate as they are harmful for the environment Contact the detergent producer if the dishes are wet and or if you notice limescale spots particularly on glasses after the washing programme is over G Adding detergent o ZN Put the detergent into the detergent dispenser just before operating the machine as Illustrated below 1 Push the latch to right to open the detergent dispenser lid A Refer to the Programme Table to determine the correct amount of detergent for the selected programme Do not put solvents into the detergent dispenser There is the risk of explosion 2 Putsuggested amount of powder or tablet detergent in the dispenser Dishwasher User s Manual 15 39 EN Preparation Inside the detergent dispenser there are level markings that help you use appropriate amount of detergent When brimful detergent dispenser will contain 40 cm of detergent F
19. anufacturers guarantee has expired If you have purchased an extended guarantee please refer to the instructions contained within the extended guarantee agreement document Otherwise please call the appropriate number above where service can be obtained at a charge Should you experience any difficulty in obtaining service please contact the Beko Customer Help Line Tel 0845 6004911 e mail service beko co uk Beko pic Beko House 1 Greenhill Crescent Watford Hertfordshire WD18 8QU UK www Dbeko co uk 15 0361 0100 REV AA 06 2015 Dishwasher User s Manual 39 39 EN
20. bleware you are going to purchase is Suitable for washing especially in the dishwasher i Decorative prints of chinaware Placing the dishes into the dishwasher You can use your dishwasher in the optimum way with respect to energy consumption and washing and drying performance only if you place the dishes in an orderly way e Wipe away any coarse food remnants bones seeds etc on the dishes before placing them in the dishwasher e Place thin narrow pieces in the middle sections of baskets If possible e There are two separate baskets in which you can place your dishes in the dishwasher Place the heavily soiled and bigger items in the lower basket and smaller delicate and light items in the upper basket e Place the hollowed dishes such as bowls glasses and pans upside down in the dishwasher Thus accumulation of water in deep hollows is prevented To prevent possible injuries always place the sharp and pointed dishes such as service fork bread knife etc upside down so as their pointed ends will face down or they will lie horizontally in the dish basket Unload dishes in the lower basket first and then the dishes in the upper basket Upper basket height adjustable rack Use the lower and upper parts of the height adjustable racks in the upper basket of the machine by sliding them down or up according to the heights of the glasses cups or etc A B C 18 39
21. cidental or consequential damages The guarantee does not in anyway diminish your statutory or legal rights The product guarantee does not cover damages to plates glass ware cutlery crockery and also damage to the product itself as a result of using these Three in one Tvvo in one detergents 38 39 EN Dishwasher User s Manual Guarantee Please keep your purchase receipt or other proof of purchase in a safe place you will need to have it should the product require attention under guarantee You should also complete the details below it will help us assist you when requesting service The model number is printed on the Instruction Booklet and the serial number is printed on the Rating Label affixed to the appliance Model No Serial No Retailer Date of purchase For service under guarantee simply telephone the appropriate number below UK Mainland amp Northern Ireland Fridges amp Freezers 0845 6004903 or 0345 6004903 Electric Cookers 0845 6004902 or 0345 6004902 Gas amp Dual Fuel Cookers 0845 6004905 or 0345 6004905 Washing Machines 0845 6004906 or 0345 6004906 amp Dishwashers Republic of Ireland All Refrigeration All Cookers 01 862 3411 Washing Machines amp Dishwashers Before requesting service please check the trouble shooting guide in the Operating Instructions as a charge may be levied where no fault is found even though your product may still be under guarantee Service once the m
22. ding salt Water softening system needs to be regenerated in order that the product operates with the same performance continuously Dishwasher salt is used for this purpose Use only special softening salts produced particularly for the dishwashers in your machine We recommend using granular or powder softening salts Do not use salts that are insoluble in water such as table salt or common salt Performance of water softening system may get worse in time c 22 Salt reservoir will fill with water when you start the product Therefore add the softening salt before starting the machine 1 First take the lower basket out to add softening salt 12 39 EN Dishwasher User s Manual Preparation 2 Turn the salt reservoir lid counter clockwise to open it A B Salt reservoir will Till with water when you Start the product Therefore add the softening Salt before starting the machine Before Initial use fill the water softening system with 1 litre of water C 3 Fill the salt reservoir with salt by using salt funnel D To speed up dissolution rate of Salt in water stir it with a spoon You can put about 2 kg of Dishwasher salt into the salt reservoir G 4 Replace the lid and tighten it securely when the reservoir is full 5 If you will not start a washing programme immediately after adding the salt run t
23. e Filters are clogged gt gt gt Check if the filter system Is clean Clean the filter system regularly as illustrated in section Cleaning and Care Filters are installed incorrectly gt gt gt Check the filter system and make sure that It Is installed correctly Baskets are overloaded gt gt gt Do not overload the baskets in excess of their capacity Detergent is stored under unsuitable conditions gt gt gt If you are using powder detergent do not store the detergent package in humid places Keep it in a closed container if possible For ease of storing we recommend you to use tablet detergents Detergent is not sufficient gt gt gt If you are using powder detergent adjust the amount of detergent according to the soiling degree of your dishes and or programme definitions We recommend you to use tablet detergents for optimum results Rinse aid is not sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting If there is enough amount of rinse aid in the machine Detergent dispenser lid is left open gt gt gt Make sure that the detergent dispenser lid is closed tightly after adding detergent Dishes are not dry at the end of cycle Dishes are not placed orderly in the machine gt gt gt Place your dishes in a way that no water will accumulate in them Dishwasher User s Manual 33 39 EN Troubleshooting e Rinse aid is not
24. e before calling the Authorised Service Agent If they are not calla qualified technician and plumber to have any necessary arrangements carried out i Preparation of the location and electrical tap water and waste water Installations at the place of installation is under customer s responsibility Manufacturer shall not be held responsible for damaqes arisinq rom processes carried out by unauthorised persons Prior to installation visually check if the product has any defects on it If so do not have it installed Damaged products Cause risks for your Safety Make sure that the water inlet and discharge hoses are not folded pinched or crushed while pushing the product into its place after installation or cleaning procedures When placing the product pay attention not to damage the floor walls piping etc Do not hold the product from its door or panel to move It Appropriate installation location e Place the product on a solid and flat floor that has sufficient load carrying capacity The product must be installed on a flat surface in order for the door to be closed comfortably and securely Do not Install the product at places where temperature may fall below UG Place the product on a rigid floor Do not place it on along pile rug or similar surfaces 0 Ensure the power cable does not get trapped under the product Make sure that you select a locatio
25. ecially Tor dishwashers only 1 Open the lid of the rinse aid reservoir by pressing Its latch B o Fillthereservoir until MAX level 3 Close the lid of the reservoir by pressing on it lightly Wipe clean any spilled rinse aid outside the reservoir Rinse ald that spilled accidentally will cause foaming and it will eventually decrease washing performance 4 Tum the rinse aid amount adjuster manually to a position between 1 and 6 4 If there are stains on tableware Dishwasher User s Manual 17 39 EN Preparation items after washing level must be increased and if there is a blue trace after wiping them by hand it must be decreased This is set to position 4 as factory default Items not suitable for washing in the dishwasher e Never wash dishes soiled by cigarette ash candle remnants polish dyestuff chemicals etc in your dishwasher Donotvvash iron alloy items in the dishwasher It can get corroded or leave stains on other items Do not wash cutlery with wooden or bone stems glued pieces or pleces that are not resistant to heat as well as copper and tin plated containers In the dishwasher as well as aluminum and silver items may get discoloured or tarnished after washing in the dishwasher just as It happens in handwashing as well Some delicate glass types and crystals may become dull in time We strongly recommend you to check if the ta
26. equency shown in the rating label corresponds to your electricity supply We recommend that this appliance be connected to the mains supply via a suitable switched and fused socket in a readily accessible position If the supply cord or the mains lead is damaged please do not replace it yourself The supply cord or the mains lead must be replaced by a Authorised Service Agent or a similarly qualified person should not be connected to any surface water drain Drainpipe must be connected 1 to the foul water system and it Adjusting the feet If the door of the product cannot be closed properly or if the product wobbles when you push it slightly then you need to adjust the feet of the product Adjust the feet of the product as illustrated in the relevant section Electrical connection Before you Insert the plug into the wall socket make sure that the voltage and n This appliance must be earthed If the fitted moulded plug is not Suitable for your socket then the plug should be cut off and an appropriate plug fitted Destroy the old plug which Is cut off as a plug with a bared cord could cause a shock hazard if inserted into a socket elsewhere in the house The moulded plug on this appliance incorporates a 13A fuse Should the fuse need to be replaced an ASTA approved BS1362 fuse of the same rating must be used Do not forget to refit the fuse cover In the event of losing the fuse cover the pl
27. et can be found amongst the usage instructions on the packages of the tablet detergents Tablet detergent types commonly found in the market 16 39 EN Dishwasher User s Manual Preparation 2in1 Contains detergent rinse aid or water softening salt 3in1 Contains detergent rinse aid and water softening Salt Ain1 Contains glass protectors in addition to detergent rinse aid and water softening salt 5in1 Contains glass and stainless steel protectors in addition to detergent rinse ald and water softening salt Observe the instructions of the 1 detergent manufacturer on the package when using tablet detergents When you switch to powder detergent from tablet detergent 1 Make sure that salt and rinse aid reservoirs are full 2 Setthe water hardness to the highest level and perform an empty run 3 After the empty washing cycle review the user manual and readjust the water hardness level so as to suit the water Supply 4 Make the appropriate rinse aid settings Rinse aid Depending on the model Salt indicator and or rinse aid indicator must be enabled again if they were disabled before The rinse aid used in dishwashers is a special combination used to increase drying efficiency and prevent water or limescale stains on the washed items For this reason care must be paid to have rinse ald in the rinse aid reservoir and to use rinse aids produced Sp
28. g unless necessary Be careful for the rush o hot steam when you need to open the door Intended use This product has been designed for domestic use 4 39 EN Dishwasher User s Manual Instructlons for safety and environment lt must be used to do the domestic type dishes only e This appliance is intended to be used in household and similar applications such as Staff kitchen areas in shops offices and other working environments e Only dishwasher safe detergents rinse aids and additives must be used e The manufacturer waives any responsibility arisen from incorrect usage or transportation e This appliance can be used by children aged from 8 years and above and persons with reduced physical sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved Children Shall not play with the appliance Cleaning and user maintenance shall not be made by children without Supervision Children s safety Electrical products are dangerous for the children Keep children away from the product when it isin use Do not let them to tamper with the product Do notforget to close the door of the product when leaving the room where It is located Store all detergents and additives in a safe place away from the reach of the children Disposing of packaging
29. gently with a mild cleaning material and damp cloth Wipe the control panel only with a damp cloth Cleaning the interior of the machine e Clean the interior of the machine and the tank by running a prewash programme without detergent or a long washing programme with detergent based on the degree of dirtiness e vvater has remained in the machine drain the vvater by performinq the procedures under the topic Cancelling a programme If the water cannot be discharged clean any leftover deposits that have piled up in the bottom of the machine blocking the water path Cleaning the filters Clean the filters at least once a week in order for the machine operates efficiently Check If food residues are left on the filters If there are food residues on filters take them out and clean well under running water 1 Tum the micro filter 1 and coarse filter 2 assembly counterclockwise and pull it out from its seating A 2 Pullout the metal plastic filter 3 from the seating C 3 Press the two pawis on the coarse filter inwards and separate the coarse filter from the assembly B 30 39 EN Dishwasher User s Manual Maintenance and cleaning 4 Clean all three filters under tap water by means of a brush 5 Replace the metal plastic filter 6 Place the coarse filter into the microfilter Make sure that it is properly seated Turn the coarse filter clockwise until a click
30. he machine empty in the shortest programme to dissolve and wash away the scattered salt in the machine Water hardness amp regeneration settings The dishwasher requires lime free water Hard water leaves watermarks on your dishes Your dishwasher has a special water softening system to remove the hardness of the tap water Setting this system correctly will increase the washing effectiveness To find out the hardness level of water in your area contact your local Water Board or Determine water hardness level by the help of test strip provided If you move to a different location the level of water hardness will possibly be different It is essential to reset the water hardness in order to obtain optimum washing efficiency Dishwasher User s Manual 13 39 EN Preparation Test Strip o eve No Lime i Level 2 Very low lime content a a Level 3 Low lime content 4 minute Level 4 Medium lime content Level 5 High lime content Level 6 Very High lime content Remove the water Fill a glass with Take the test strip Hold for Set the water hardness level of your dishwasher test strip from flow from your tap water and out of the water and 1 minute according to the result shown by the test strip its packing tap for 1 minute dip the test strip shake it into water for 1 second To
31. ill detergent up to 15 cm or 25 cm level marks in the detergent dispenser according to fullness of the machine and or soiling degree of the dishes 1 If dishes have been waiting for a long time and have dried residues fill the 5 cm compartment too 5 3 Close the detergent dispenser lid by pressing on it lightly A click will be heard when the lid is closed In programmes with prewash and at high temperature In which you use tablet detergents make sure that the detergent dispenser lid is closed firmly Use powder detergent in short programmes without prewash since the solubility of the tablet detergent changes depending on the temperature and time Excessive usage of powder detergents will cause the detergent not dissolve completely and will also cause scratches on the glassware A Tablet detergents Tablet detergents exhibit water softening and or rinse aid effect in addition to detergent effect Some types of these detergents also contain special purpose washing chemicals such as glass and stainless steel protectors Tablet detergents give satisfying results only under certain usage conditions The best washing performance in dishwashers is obtained by using detergent rinse aid and water softening salt individually Information about suitable places detergent dispenser basket etc in the dishwasher to place the tabl
32. in tableware items do not recommend washing such kitchen utensils in the dishwashers either Dishes are scratched Kitchen utensils that contains or are made of aluminum should not be washed in dishwasher e Salt leakage exists gt gt gt Pay attention not to spill salt around the salt filling hole while adding salt Spilled salt can cause scratches Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the Salt that spilled inside the machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme e Water hardness setting is low or salt level is insufficient gt gt gt Measure the hardness of the supply water appropriately and check the water hardness setting Dishes are not placed orderly in the machine gt gt gt When placing the glasses and other glassware into the basket lean them not against other dishes but the edges or racks of the basket or the glass support tines Striking of the glasses to each other or to other dishes due to the impact of water during washing can cause breaks or scratches on their Surfaces 36 39 EN Dishwasher User s Manual Troubleshooting A smear remains on glasses that resembles milk stain which can not be removed when wiped by hand A bluish rainbow appearance occurs when the glas
33. llapsible tines will click into the latch again C NJ 1 b 7 cdl zr suv ANTS Bringing the tines to the horizontal position by holding them from the tips may cause them to bend Therefore it will be appropriate to bring the tines in the middle to horizontal or vertical position by holding them from their stems and pushing in the direction of 22 39 EN dl FOW Dishwasher Users Manual 5 Operating the product Display On Off key Start Pause Cancel key Time Delay key Function keys 2 3 Half Load Function Fast Function a b C SteamGloss function d Aqualntense Function 6 Programme Selection keys 10 16 7 Programme indicator 8 Salt S indicator 9 Notin use 10 Start b Pause indicator 11 Time Delay indicator 13 1211 12 End of Programme indicator 13 Screen information line 14 Child Lock indicator 15 Rinse ald 5 indicator 16 Notin use Dishvvasher Users Manual 23 39 EN Operating the product Keys On Off key t is used to turn on or off the machine Press On Off Key to switch ON A signal is heard and the machine door is turned on Press the On Off key for 1 second to turn off A signal will be heard and machine will turn off at the end of 1 second To turn off while the programme is running keep Off key pressed for 3 seconds A countdown in the form of
34. lt your local authorities to learn about these collection centers Compliance with RoHS Directive The product you have purchased complies with EU RoHS Directive 2011 65 EU It does not contain harmful and prohibited materials specified in the Directive Package information Packaging materials of the roduct are manufactured rom recyclable materials in accordance with our National Environment Regulations Do not dispose of the packaging materials together with the domestic or other wastes Take them to the packaging material 6 39 EN Dishwasher User s Manual Bi Dishwasher Overview 15 14 13 G B ND eS T 10 al yana Upper basket Upper impeller Lower impeller Filters Lower basket Rating Label Control panel Door Detergent dispenser 10 Cutlery basket 11 Salt reservoir lid 12 Upper basket rail 13 Upper cutlery basket 14 Top Cover 15 Ceiling impeller 16 Fan drying system Dishwasher User s Manual 7 39 EN Dishwasher Technical specifications Compliance to standards and test data EC declaration of conformity C This product complies with the following EU directives Development production and sales stages of this product comply with the safety rules included in all pertaining European Community regulations 2006 95 2004 108 EC 93 68 EC IEC 60436 DIN 44990 EN 50242 220 240 V 50 Hz see rating label Total power
35. lug is damaged Call the Authorised Service Agent Connect the product to a 7 outlet protected y a fuse complying with the values in the Technical specifications table Do not neglect to have the ing installation made y a qualified electrician Our company shall not be liable for any damages that will arise when the product is used without grounding in accordance with tne local regulations The water supply and draining hoses must be securely fastened and remain undamaged Unplug the product when not In Use Never wash the product by 7 pourinq vvater onto itl There is the risk of electric shock Never touch the plug with wet hands Never unplug by pulling on the cable always n out by grabbing the plug he product must be unplugged during installation maintenance cleaning and repairing procedures Always have the repair procedures carried out by the Authorised Service Agent Manufacturer shall not be held liable for damages that may arise from procedures Carried out by unauthorised ersons Never use chemical solvents in the product They bring forth the risk of explosion When you pull the upper and lower baskets out completely the door of the product will bear all the weight of the baskets Do not put other loads on the door the product may ilt Never leave the door of the product open apart from loading and unloading rocedures o not to open the door of the product when it is runnin
36. n If the function button is pressed again the symbol will disappear and selection is cancelled 3 Selection will be cancelled when you press the function key again Half Load function It is used to operate the machine without loading it completely 1 Load your dishes in the machine as you like 2 Turn the machine on with On Off key 3 Select the desired programme and press the Half Load key The Half Load can save both water and power while using the lower and upper baskets of the machine Fast Function It shortens the time of the washing cycle selected and decreases water consumption by enabling washing under higher pressure SteamGloss function It provides superior drying performance Aqualntense Function Wz Aqualntense impeller located under the lower impeller helps washing your heavily soiled dishes places in the right side of the lower basket It will give better results to place the most soiled dish to the right front Side Do not try to remove the Aqualntense impeller Automatic Detergent Detection Feature The product has a feature to automatically detect the type of the detergent and adjust the washing programme and drying system to the best performance If special tablet detergent is used the programme duration can be extended by 20 minutes in order to optimize the washing and drying performance To deactivate 1 After turning on the machi
37. n that will allow you to load and unload the dishes in a fast and comfortable manner Install the product in a place close to the tap and the drain Select the installation location by considering that it will not be changed after the connections are made Connecting water supply Do not use old or used water inlet hose on the new product Use the new water inlet hose supplied with the product Connect the water inlet hose directly to the water tap Pressure coming from the tap should be minimum 0 3 and maximum 10 bars If the water pressure exceeds 10 bars a pressure relief valve should be Installed in between Open the tap completely after making the connections to check for water leaks For your safety close the water inlet tap completely after the washing programme is over ZN Connection to the drain Water discharge hose can directly be connected to the drain hole or sink s Dishwasher User s Manual 9 39 EN Installation drainage The length of this connection must be min 50 cm and max 100 cm from the floor A discharge hose longer than 4 meters will cause washing performance to be affected Attach the water discharge hose to the drainpipe without bending it Tightly fix the water discharge hose to the drainpipe in order to prevent any dislocation of the water discharge hose during operation of the product Dl max 1000 the fr
38. ndles or container lids Accessories or consumable items including but not limited to ice trays scrapers cutlery baskets filters and light bulbs e Repairs required as a result of unauthorised repair or inexpert installation that fails to meet the requirements contained in the user Instruction book e Repairs to products used on commercial or non residential household premises Loss of frozen food in freezers or ridqe Treezers Food loss insurance is often included within your household contents insurance policy or may be available separately from your retailer Important notes Your Beko product is designed and built for domestic household use only The guarantee will be void if the product is installed or used in commercial or non residential domestic household premises The product must be correctly installed located and operated in accordance with the instructions contained in the User Instructions Booklet provided Professional installation by a qualified Electrical Domestic Appliance Installer Is recommended for all Washing Machines Dishwashers and Electric Cookers Gas Cookers must only be installed by a Gas Safe or BORD GAIS registered Gas Installer The guarantee Is given only within the boundaries of the United Kingdom and the Republic of Ireland The guarantee Is applicable only to new products and is not transferable if the product Is resold Beko disclaims any liability Tor in
39. ne press and hold Time Delay and Programme keys simultaneously for 3 seconds 26 39 EN Dishwasher User s Manual Operating the product 2 Press the Programme key until tablet icon is displayed When you enter the Automatic Detergent Detection Feature menu tablet icon will start to flash and the active setting will be displayed Automatic Detergent Detection ON P1 Automatic Detergent Detection OFF P2 3 Automatic Detergent Detection Feature is turned ON and OFF with the Time Delay key 4 Turn off the machine with On Off key to save the changes While the Automatic Detergent Detection Feature is active or passive the Tablet Detergent indicator is not displayed Changing Warning Sound Volume Your machine is equipped with an audio Signal to inform warnings audibly 1 After turning on the machine press Time Delay and P keys Simultaneously Continue to press until the countdown 3 2 1 is completed on the display 2 Press P key to activate the S position 3 Select one of 51 52 and SO with Time Delay key 4 Turn off the machine with On Off button to save the changes Programming the washing time Time Delay If an economical electricity tariff is applied in your region you can use the Time Delay function to vvash your dishes durinq appropriate hours You can delay the start of the selected programme until 24 hours Time Delay cannot be set after the programme starts 1 Press
40. one 24 39 EN Dishwasher User s Manual SUOIPUOD 62106 Japun 2 10 4 194 ABW s v l Hiq SUOIIPUOD 5 JOPUN LH M QE v Ul UMOUS S nD EA UONdWNSUOD BU ewWWeIGOJd s 94 Husn pue oasa pie SULL IIRI e pue s su dSI p 15S H U NOS J9 EM YIM NO p LLE q snw ZPZOG NJ UM soUePsJONIR Ul 5159 S mi s l B ns 10 NSEQ y Ul paysem s us p Jo s d eq ued s e n JE 40 lqeq ns dnpying nopo pue sued jayseq Ajeonewozne peq y J ddn y ul w Buiysem Buljlos JO snu p ysem 54 y SE Il M pue s ep maj e Aem 1S SE SSEIB se sayem DUIUSEA JO SUIYDEW v UI y Ul pauesjO ue HUAA Swe y JO d y ase Buryiem d y q Suna jdey oe onseld Sulpnioul pue yey s usip 18 s us p p llos p ysem 180 s ys p p llos s us p pexiw Ilep y 5199 p llos winipew u UO 51 JO pades ae ey nq peuesgjo v yorym sued pue JO wwepod pue s us p y y JO 5 y s us p p llos jou ey ye sjod s us p p llos S
41. s in excess of their capacity Water remains in the dishwasher at the end of the programme Filters are clogged gt gt gt Check if the filter system Is clean Clean the filter system regularly as illustrated in section Cleaning and Care e Discharge hose is clogged blocked gt gt gt Check the discharge hose If necessary remove the discharge hose clear the blockage and insert Is as illustrated in the user manual If you cannot eliminate the problem although you follow the instructions in this section consult your dealer or the Authorised Service Agent Never try to repair a nonfunctional product yourself G Dishwasher User s Manual 37 39 EN 8 Guarantee Guarantee for Refrigeration Cooking Appliances Washing Machines amp Dishwashers Please visit the Support section on the Beko website at www beko co uk to register your one year warranty Your new Beko product is guaranteed against the cost of breakdown repairs for one year from the date of the original purchase What is covered e Repairs necessary as a result of faulty materials defective components or manufacturing defect e The cost of functional replacement parts but excluding consumable items The labour costs of a Beko approved repairer to carry out the repair What is not covered e Transit delivery or accidental damage or misuse and abuse Cabinet or appearance parts including knobs flaps ha
42. s is pointed to light e Excessive rinse ald is used gt gt gt Lower rinse ald setting Clean the spilled rinse ald when adding rinse aid Corrosion has occurred on glass due to soft water gt gt gt Measure the hardness of the Supply water appropriately and check the water hardness setting If your supply water is soft lt 5 dH do not use salt Choose programmes that wash in higher temperatures e g 60 6590 You can also use glass protective detergents that are commercially available Foam forms in the machine e Dishes are washed with hand wash detergent by hand but not rinsed before placing them into the machine gt gt gt Hand wash detergents do not contain antifoam There is no need to hand wash the dishes before placing them into the machine Removing the coarse 501 on the dishes under tap water with a tissue paper or fork will be sufficient e Rinse aid has spilled into the machine when adding rinse aid gt gt gt Take care that rinse aid is not spilled in the machine when you are filling it Clean any spilled rinse ait with the help of a tissue paper towel Lid of the rinse aid reservoir is left open gt gt gt Make sure that the lid of the rinse aid reservoir is closed after adding rinse aid Kitchen utensils are broken e Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual e Baskets are overloaded gt gt gt Do not overload the basket
43. sufficient gt gt gt Check the rinse aid indicator and add rinse aid if necessary Increase the rinse aid setting If there is enough amount of rinse aid in the machine e Machine is unloaded right after the programme is over gt gt gt Do not unload your machine right after washing process is completed Slightly open the door and wait for evacuation of the steam inside for a while Unload the dishes after the pieces cool down to a touchable level Start unloading process from the lower basket Thus dropping of water remained on a piece at upper basket onto the pieces at lower basket is prevented Selected programme is unsuitable gt gt gt Since rinsing temperature is low at programmes with short duration drying performance will also be low Select programmes with longer duration for a higher drying performance e Surface quality of the kitchen utensils is deteriorated gt gt gt Desired washing performance can not be obtained on kitchen utensils with deteriorated surfaces and It is not suitable to use such utensils in terms of hygiene as well Also water can not flow easily on deteriorated surfaces It is not recommended to wash such kitchen utensils in dishwasher i It is normal that drying complaints can be experienced with Teflon kitchen utensils It is associated with the structure of Teflon Since the surface tensions of Teflon and water are different water droplets will remain as beads on the Teflon surface
44. t There might be a small amount of water left in the product after factory quality control tests This causes no harm to the product Dishwasher User s Manual 11 39 EN 4 Preparation Tips for energy saving Following information will help you use the product in an ecological and energy efficient manner Wipe away any coarse food remnants on the dishes before putting them in the product Operate the product after filling it completely When selecting a programme consider the table of Programme data and average consumption values Do not put more detergent than suggested on the detergent package Water softening system G Your dishwasher requires soft water If the hardness of the water is above 6 dH the water must be softened and descaled Otherwise ions that create the hardness will accumulate on the surfaces of the dishes and may adversely affect the washing shining and drying performances of the product The product is equipped with a water softening system which reduces the hardness of incoming water This system softens the supply water that enters into the product to a level that will allow washing the dishes with the required quality Adjusting the water softening system Washing performance will increase when water softening system is adjusted properly Adjust the new water hardness level according to the Water hardness level instruction in this booklet Ad
45. ter finishing the filling process Run the prewash programme to remove the Salt that spilled inside the 34 39 EN Dishwasher User s Manual Troubleshooting machine Since the salt granules that will remain under the lid will dissolve during prewash causing the lid loosen check the lid once again at the end of the programme There is a different odour in the machine 1 Anew machine has a peculiar odour It will fade out after a couple of washes e Filters are clogged gt gt gt Check if the filter system Is clean Clean the filter system regularly as illustrated in section Cleaning and Care e Dirty dishes are kept in dishwasher for 2 3 days gt gt gt If you are not going to start the machine right after you have put the dishes into It remove the remnants on the dishes and run the Prewash programme without detergent every 2 days In such cases do not close the door of the machine completely in order to avoid odour build up in machine You can also use commercially available odour removers or machine cleaners Rust discoloration or surface deterioration occurs on dishes Salt leakage exists gt gt gt Salt may cause deterioration and oxidation on metal surfaces Pay attention not to spill salt around the salt filling hole while adding salt Make sure that the salt reservoir lid is tightly closed after finishing the filling process Run the prewash programme to remove the Salt that spilled inside the
46. the Time Delay function key after selecting the washing programme and other auxiliary functions 2 Once you press the Time Delay key Display Information Line will show 0 30 and Time Delay indicator will start flashing 3 Setthe desired time by pressing the Time Delay key Time will increase with increments of 30 minutes up to 6 hours and after that in 1 hour increments up to 24 hours every time you press the key 4 Press Start Pause Cancel key to start countdown for the Time Delay Time Delay indicator and Start Pause indicator will light continuously until the end of the period Time Delay is displayed on the Display Information Line Selected programme will start as soon as the countdown is over Changing the settings while Time Delay function is enabled While the Time Delay function is activated you cannot make changes in the washing programme auxiliary functions or the duration of delay time G Programme and auxiliary functions cannot be set changed after the programme has started To cancel the Time Delay function 1 Press and hold Start Pause Cancel key for 3 seconds 2 When the Start Pause Cancel key s pressed and hold 3 2 1 appear on the Display Information Line Time Delay indicator will turn off at the end of the cancellation process and delaying process Is cancelled G You can select and start a new programme following the cancellation of Time Delay function
47. the nut Is tightened well upwards and then 9 turn left A B when installing the upper impeller To install the impeller seat it into its SS TEN AR 1 slot push slightly upwards and turn it riqhtvvards until it is securely tightened When the Impeller is released check if it rotates without any obstruction 32 39 EN Dishwasher User s Manual 7 Troubleshooting Machine does not start Power cable is unplugged gt gt gt Check if the power cable is plugged in Fuse is blown gt gt gt Check the fuses in your house Water is cut gt gt gt Make sure that the water inlet tap is open Door of the machine is open gt gt gt Make sure that you have closed the door of the machine On Off button is not pressed gt gt gt Make sure that you have turned on the machine by pressing the On Off button Dishes are not washed clean Dishes are not placed orderly in the machine gt gt gt Load the dishes as described in the user manual Selected programme is unsuitable gt gt gt Select a programme with a higher temperature and cycle time Impellers are stuck gt gt gt Prior to starting the programme turn the lower and upper impellers by hand to make sure that they rotate freely Impeller holes are clogged gt gt gt Lower and upper impeller holes might be clogged with food remnants such as lemon pips Clean the impellers regularly as illustrated in section Cleaning and Car
48. u are using well water than it is recommended to use filter and water purification devices Ifthe hardness level of the water that you use is below 8 dF French standard for water hardness there is no need to use Salt in your dishwasher If this is the case Salt Indicator if any illuminates continuously on the panel of your machine If the water hardness is set to level 1 the Salt Indicator will illuminate continuously although it is not necessary to use Salt If you use salt under this condition salt will not be consumed and the lamp will not illuminate Regeneration Adjustment Switch 14 39 EN Dishwasher User s Manual Preparation G If you move your house it IS very important to make the water hardness level adjustment of your machine according to the new location you move to In order to preserve the washing efficiency If the water hardness level of your machine Is adjusted previously your machine will display the most recent hardness level adjustment Adjust the new water hardness level of the machine based on the water hardness level of the tap water Since different salt brands in the market have different particle sizes and since the water hardness may vary dissolution of the s
49. ug must not be used until a replacement fuse cover has been fitted Colour of the replacement fuse cover must be the same colour as that visible on the pin face of the plug Fuse covers are available from any good electrical store 10 39 EN Dishwasher User s Manual Installation Fitting a different plug As the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals on your plug proceed as follows 1 Connect the green yellow or green earth wire to the terminal in the plug marked E or with the symbol Or coloured green and yellow or green 2 Connect the blue neutral wire to the terminal in the plug marked Nor coloured black 3 Connect the brown live wire to the terminal in the plug marked Tor coloured red Green and yellow or green Blue or ack Brown or red With the alternative plugs a 13A fuse must be fitted either in the plug or adaptor or in the main fuse box If in doubt contact a qualified electrician Initial use Before starting to use the product make sure that all preparations are made in accordance vvith the instructions in sections Important safety instructions and Installation Before using the product Till the salt reservoir with 1 litre of water add salt see next page and stir to dissolve Run the Dishwasher without dishes on a short programme with a small amount of detergen
50. ulUSEA jqeyns qo 5 Bulysem JO lqeq ns Anyi so Bjqeyns s usip 104 ajqeyins Bulysem Ajieq Ajiaeay 40 ajqeyins JSOW U 51 y SOUIWI9 98q 621 1SOVN Q o USE M Lci 0 IUIN HEO SSEV uea gyno AISU JU x l Ienbvy ony ulpu O O ajqey ululp Bold 25 39 EN Dishwasher User s Manual Operating the product Auxiliary functions Washing programmes of your dishwasher are designed to obtain the best cleaning effect considering the type of the soil soiling degree and properties of the dishes to be washed Auxiliary functions are provided in order to enable you to save time water and energy and to perform a more comfortable washing with conditions specific to you Indicator will light on the display in the Function Selected indicator 4 Close the door of the machine to start the programme i With the Half Load function you Auxiliary functions may cause duration Auxiliary functions are not Suitable for all washing programs Indicator of the auxiliary function that is not compatible with the programme will not be active changes In the programme To add auxiliary function to the programme 1 Select the desired washing programme by pressing the programme selection key 2 Inthe selected washing programme if auxiliary function is selected its symbol will be displayed on the scree
51. ying effectiveness of your machine Water cut off warning If mains water is cut or water inlet tap is turned off the machine cannot take water in and E 02 icon will flash on the programme indicator As long as the problem continues washing programme is paused and the water inlet is checked regularly by the machine when the water is restored E 02 icon will disappear after a while and the washing programme resumes Overflowing warning If the machine intakes too much water or there is leakage at any of the components then the machine will detect this and E 01 icon will flash on the Programme indicator As long as the overflowing continues safety algorithm will be active and try to discharge the water If overflowing stops and safety is assured E 01 icon will disappear If E 01 does not disappear there is a permanent fault In this case the authorised service should be contacted Dishwasher User s Manual 29 39 EN 6 Maintenance and cleaning Service life of the product extends and frequently faced problems decrease if it is cleaned at regular intervals fl Unpluq the product and turn off the tap before attempting any Do not use abrasive substances for cleaning cleaning procedures Clean the filter and impellers at least once a week to ensure the machine operates efficiently Cleaning the outer surface of the product Clean the outer surface and door gaskets of the product
Download Pdf Manuals
Related Search