PS6S1800M User Guide - Pdfstream.manualsonline.com
Contents
1. Mobility Electronics Inc 9918 Via Pasar San Diego CA 92126 USA Phone 858 880 2225 Fax 858 530 2733 www invisioncradles com O e iud WISIOn PS6S1800M User Guide MOBILITY ELECTRONICS INC Serial Modem Charging Cradle MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Copyright 2005 Mobility Electronics Inc All rights reserved The information in this document is subject to change without notice Disclaimer Mobility Electronics Inc assumes no responsibility for any damage or loss resulting from the use of this user guide Mobility Electronics Inc assumes no responsibility for any loss or claims by third parties that may arise through the use of this product Mobility Electronics nc assumes no responsibility for any damage or loss caused by deletion of data as a result of malfunction dead battery or repairs Be sure to make backup copies of all important data on other media to protect against data loss First Edition September 2005 Rev A Trademarks Symbol is a registered trademark of Symbol Inc PalmOS and HotSync are registered trademarks and Palm is a trademark of Palm Inc or its subsidiaries Third party products and brand names may be trademarks or registered trademarks of their respective owners Microsoft Windows Window ME and Windows NT are either registered trademarks or trademarks of Microsoft Corporation in the United States and2. The serial cable is not connected Check to make sure that the serial cable is properly connected to the cradle and to the host computer correctly The terminal is not fully seated in the Remove and re insert the terminal into the cradle cradle Make sure it is firmly seated Communications software is not installed Perform setup as described by the terminal or is not configured properly manufacturer Modem Serial switch is not set correctly Check to be sure the Modem Serial switch is set to Serial Mobility Electronics Inc p MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Symptom Attempt by the cradle to HotSync the terminal through the modem failed Possible Cause Action O O The terminal was removed from the Place the terminal back in the cradle to allow the cradle while the HotSync was in cradle to make another HotSync attempt progress Terminal or cradle was disconnected from Unplug the modem cable for 30 seconds to allow the telephone line while the HotSync was the local telephone connection to hang up Be in progress sure to close any open windows on the terminal and any modem connections Terminal s battery is dead Wait for two 2 minutes before trying a HotSync again to allow the battery to recharge Active Error dialog box on terminal The Error dialog box on the terminal must be cleared Use the stylus to press OK on the terminal s touchscreen Mod
3. advance that Mobility Electronics Inc 11 MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide temporary discontinuance of service may be required Also you will be advised of your right to file complaint with the FCC if you believe it is necessary e The telephone company may make changes in its facilities equipment operations or procedures that could affect the operation of this equipment If this happens the telephone company will provide advance notice in order for you to make necessary modifications to maintain uninterrupted service e If trouble is experienced with this equipment the Serial Modem Charging Cradle PS6S1800M then contact Mobility Electronics 858 880 2225 for repair or warranty information If the equipment is causing harm to the telephone network the telephone company may request that you disconnect the equipment until the problem is resolved e his equipment must not be used on party lines e f your home has specially wired alarm equipment connected to the telephone line ensure the installation of this modem does not disable your alarm equipment If you have questions about what will disable alarm equipment consult your telephone company e No user repairable parts are contained within this equipment Canada This equipment meets the applicable Industry Canada Terminal Equipment Technical Specifications This is confirmed by the registration number on the product label The abbrev
4. REEN when the battery is fully charged approximately 3 hours MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Product Technical Support Mobility is committed to providing its customers with first class customer service and technical support For your convenience a few troubleshooting techniques are provided below that might help you fix your problem quickly and easily If you have a different issue or if you have tried these and they didn t resolve your problem please feel free to contact Technical Support at Mobility Electronics 9918 Via Pasar San Diego CA 92126 Phone 858 880 2225 Fax 858 530 2733 E mail handheld connectivity o mobl com Web www invisioncradles com o S If you use the website please select the Cradles Adapters JIOWISIOTL menu option from the Support menu MOBILITY ELECTRONICS INC Products Support Nev Presentation Solutions Product Registration OA A product registration card is included with your PS6S1800M product Please fill out the registration card and drop it in the mail so that we will know who you are if you ever need to call While registration is not required to resolve warranty claims it will help make any warranty claim easier to complete For your convenience you may also register online at www invisioncradles com Troubleshooting Symptom Terminal cannot communicate through the serial cable Possible Cause
5. and or remote location must be correctly configured and the cradle and phone line or serial cable must be plugged in as previously described See the Product Reference Guide provided by the terminal manufacturer for more information on configuring the SPT terminal computer or remote location for HotSync operations MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Charging the SPT Terminal Battery The cradle may also be used to charge the SPT terminal lithium ion battery To charge the terminal s battery 1 Ensure the cradle is powered on i i Symbol 1700 1800 2 Insert the terminal in the cradle as shown a The Terminal Battery Charge LED will turn RED to indicate that the terminal is charging b When the terminal has completed charging the light will turn GREEN to indicate the battery is fully charged approximately 3 hours Spare Battery Charging Terminal Battery Charge LED turns RED while charging and GREEN when fully charged To charge the terminal s spare battery Symbol 1700 1800 l Compatible Battery 1 Orient the battery so that the charging contacts are facing down and toward the back of the cradle 2 Insert the battery in the spare battery charging slot in the top of the cradle as shown Then gently press down on the battery to ensure proper contact peig The Spare Battery Charge LED turns RED to indicate the battery is charging The LED turns G
6. bject to Mobility Electronics Inc s existing restocking policy MOBILITY ELECTRONICS INC WARRANTS THAT THIS PRODUCT IS NEW OR HAS BEEN REMANUFACTURED TO MEET NEW STANDARDS USING NEW OR SERVICEABLE USED PARTS MOBILITY INC MAKES NO OTHER WARRANTY EITHER EXPRESSED OR IMPLIED WITH RESPECT TO THIS PRODUCT MOBILITY INC SPECIFICALLY DISCLAIMS THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE Some states or provinces do not allow limitations on how long an implied warranty lasts so the above limitation or exclusion may not apply to you THE REMEDIES PROVIDED HEREIN ARE CUSTOMER S SOLE AND EXCLUSIVE REMEDIES IN NO EVENT SHALL MOBILITY INC BE LIABLE FOR ANY LOST PROFITS DIRECT INDIRECT SPECIAL INCIDENTAL OR CONSEQUENTI AL DAMAGES WHETHER BASED ON CONTRACT TORT OR ANY OTHER LEGAL THEORY Mobility Electronics Inc 14 MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide MOBILITY ELECTRONICS INC Mobility California Inc 9918 Via Pasar San Diego CA 92126 USA Phone 858 880 2225 Fax 858 530 2733 Email invisioncradles mobl com www invisioncradles com Part Number 190086 000 Rev A
7. ectronics jiddikjara li dan modem jikkonforma mal htigijiet essenzjali u ma provvedimenti ohrajn relevanti li hemm fid Dirrettiva 1999 5 EC Estonian Kaesolevaga kinnitab Mobility Electronics seadme modem vastavust direktiivi 1999 5 EU p hin uetele ja nimetatud direktiivist tulenevatele teistele asjakohastele satetele Alul rott Mobility Electronics nyilatkozom hogy a modem medgfelel a vonatkoz alapvet k vetelm nyeknek s az 1999 5 EC ir nyelv egy b el r sainak Mobility Electronics t mto vyhlasuje Ze modem spl a z kladn po iadavky a v etky pr slu n ustanovenia Smernice 1999 5 ES Czech Mobility Electronics t mto prohla uje Ze tento modem je ve shod se z kladn mi po adavky a dal mi p slu n mi ustanoven mi sm rnice 1999 5 E iuo Mobility Electronics deklaruoja kad is modem atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas iuo Mobility Electronics deklaruoja kad is modem atitinka esminius reikalavimus ir kitas 1999 5 EB Direktyvos nuostatas Latvian Ar so Mobility Electronics deklar ka modem atbilst Direkt vas 1999 5 EK b tiskaj m pras b m un citiem ar to saist tajiem noteikumiem Italian Hungarian MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Appendix B Warranty Mobility Electronics Inc warrants this product against defects in materials and workmanship to the original purchaser or the first pu
8. em or telephone lines being operated Modify init string in US Canada to AT amp F N5 in an electrically noisy environment forcing MNP error correction or AT amp F MS V32B forcing B32bis 14 400 bps connection For International operation use ATS amp F N5 GCl 2xx forcing MNP error correction or AT amp F MS V32B GCl xx forcing V32bis 14 400 bps connection Mobility Electronics Inc MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Symptom Terminal cannot communicate through the modem Possible Cause Action e The modem cable is not connected Check to be sure the modem cable is properly connected securely to the cradle and to the analog telephone jack The cradle is not getting power Check to be sure the power cable is connected securely to both the cradle and to the AC power The terminal is not fully seated in the Remove and re insert the terminal into the cradle cradle Make sure it is firmly seated Communications software is not installed Perform setup as described by the terminal or is not configured properly manufacturer Configuration parameters are lost after a Perform setup as described by the terminal cold boot hard reset is performed manufacturer Connection method for the modem is set Perform setup as described by the terminal incorrectly manufacturer Problems in the telephone lines that Connect a conventional telep
9. ephone cord that used to be the Line In Jac in the Standard Wall Outlet into telephone cord that on the rear of the cradle the Line Out Jack on the cradle used to be in the wall before step en above into the Line Out jack on the back of the cradle Set the Modem Serial switch to Modem for modem operations Standard Analog Single Line Telephone Not Included MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Operating the Cradle The Sync Select switch on the back of the PS6S1800M cradle can be set in either of two positions MODEM SERIAL Move the switch to the Move the switch to the left hand position for right hand position for serial modem communications SERIAL communications While in this position the While in this position the cradle automatically DA cradle automatically wakes wakes up the SPT the SPT terminal if it is terminal if it is asleep asleep and performs a initializes the modem MODEM SERIAL serial HotSync when electronics and performs the HotSync button a modem HotSync O is pressed when the HotSync button is pressed You will be able to hear the modem working while it is dialing and making the HotSync connection O If the terminal has been previously configured for these HotSync activities there is nothing left to do but Push the HotSync button In order to properly perform a HotSync the SPT terminal computer
10. hone to the phone prevent communication line and dial the remote modem to verify that the telephone lines are working correctly If you do not hear the remote modem answer your call and issue the modem connect signal contact the Remote System Administrator If you do hear the connect signal the problem is with your setup or equipment Check your cables cords connections and configuration setup before trying again Modem Serial switch is not set correctly Check to be sure the Modem Serial switch is set to Modem Mobility Electronics Inc 9 MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Symptom Terminal has successfully connected through the modem but no data is being transmitted over the connection Data is being transferred over the S24 To temporarily disable the radio link and force radio link the data transmission to use the modem connection follow the instructions provided by the manufacturer for communicating with radio links If you plan to use a wireless connection later don t forget to re enable the radio link Other HotSync Problems If you require more information on the HotSync process please refer to the HotSync chapter in your SPT Product Reference Guide For help with other technical issues contact Mobility Technical Support using the contact information provided at the start of this chapter MOBILITY ELECTRONICS INC invision Serial Modem Charging C
11. iation I C before the registration number signifies that registration was performed based on a Declaration of Conformity indicating that Industry Canada technical specifications were met It does not imply that Industry Canada approved the equipment The European Economic Area Mobility Electronics hereby declares that this device is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC A Declaration of Conformity may be obtained from http www mobilityelectronics com hh cradle support The modem is designed to work with the following Public Switched Telephone Networks Belgium Netherlands Luxemburg Germany France Italy Finland Sweden Norway Switzerland Denmark UK Ireland Spain Austria Portugal Greece Estonia Latvia Lithuania Poland Czech Republic Slovakia Hungary Cyprus Malta and Slovenia English Hereby Mobility Electronics declares that this modem is in compliance with the essential requirements and other relevant provisions of Directive 1999 5 EC Finnish Mobility Electronics vakuuttaa t ten ett modem tyyppinen laite on direktiivin 1999 5 EY oleellisten vaatimusten ja sit koskevien direktiivin muiden ehtojen mukainen Dutch Hierbij verklaart Mobility Electronics dat het toestel modem in overeenstemming is met de essenti le eisen en de andere relevante bepalingen van richtlijn 1999 5 EG French Par la pr sente Mobility Electronics d clare que l appareil m
12. ital apparatus complies with Canadian I CES 003 Cet appareil num rique de la classe B est conforme la norme NMB 003 du Canada Telecom Compliance Warnings and Notices United States The applicable regulatory notices for the United States include e This equipment complies with Part 68 of the FCC rules and requirements adopted by ACTA On the bottom of this equipment is a label that contains a product identifier in the format US AAAEQZ ZTXXXX If requested this number must be provided to the telephone company e The Ringer Equivalency Number REN determines the number of devices that may be connected to a telephone line Excessive RENs on a telephone line may result in devices not ringing in response to an incoming call In most areas the sum of RENs should not exceed five 5 0 The REN for this product is part of the product identifier that has the format US AAAEQZZTXXXX The digits represented by are the REN without a decimal point e This equipment must be connected to the telephone network or premises wiring using a compatible modular jack RJ 11C compliant with the applicable FCC Part 68 rules and requirements adopted by ACTA A compliant telephone cord and modular plug are provided with this product It is designed to be connected to a compatible modular jack that is also compliant e If this equipment the Serial Modem Charging Cradle PS6S1800M causes harm to the telephone network the telephone company will notify you in
13. l communications port on your computer E Change the Modem Serial Switch to the Serial position Your PS6S1800M requires a dedicated port It cannot share a port with an Caution internal modem or other device If you are unsure about the location of the serial port on your computer refer to the user s manual supplied with the computer Invision Serial Modem Charging Cradle User Guide Plug the RJ 45 connector into the Serial Jack on the rear of the cradle Connect the DB 9 pin female connector to the DB 9 pin male connector on the SER1 SER2 ports on the back of your computer Standard desktop or laptop computer with at least one male DB 9 pin connector Not Included MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide HotSync with a Remote Location To HotSync your terminal with data at a remote location follow these simple steps Connect one RJ 11 end of the included telephone cord into a v Standard Wall Outlet with standard analog amp RI 11 Telephone Jack telephone wall jack Modem 5erial Switch Connect the other RJ 11 end to the Line In jack on the back of the PS6S1800M cradle e i you plan to share your telephone line for VOICE Plug one end of the communications RJ 11 Telephone If you plan to share the Cord into a Standard c nice cz comecheRUAT Sei T end of the anal OQ and p the cha T into tel
14. le PS651800M P Rear View Use the power adapter supplied with your Symbol terminal Connect the barrel end of the power adapter into the 9VDC jack on the rear of the cradle If you need another power adapter contact Mobility US users may use the Mobility Power Adapter PN 170182 002 for US Standard 110V use only The PS6S1800M cradle is compatible with the power adapter used by your Symbol 1700 or 1800 terminal If replacing the power adapter US users may Leal use the Mobility Power Adapter PN 170182 002 a universal auto switching Important power adapter This product ships with a detachable US Standard 110V power cord that might be changed to match other power receptacles if you have a different power requirement You might also use a power cord converter to allow the power adapter to plug into other power receptacles If you have any other questions contact Mobility HotSync Connection Before you prepare the PS6S1800M cradle for HotSync communications you must decide which type of HotSync communication you desire 1 HotSync with the computer or 2 HotSync with a remote location MOBILITY ELECTRONICS INC HotSync with the Computer To HotSync your terminal with data on your computer follow these simple steps O Plug the RJ 45 Moden Serial connector into the TW Serial Jack on rear of the PS6S1800M cradle Turn off your computer and plug the DB 9 connector into the seria
15. odem Serial Switch corporate databases and other host computers There are four connection ports on the rear of the PS6S1800M OV 2A Power Port RJ 11 RJ 11 RJ 45 Phone Line In Phone Line Out Serial Port Used to connect to a handset in a loop through fashion Line Out use with standard RJ to allow voice communications when the cradle is not 11 connectors being used for HotSync communications to other computers Used for direct connection to your computer using the supplied RJ 45 to DB 9 cable Serial RJ 45 Serial Port Only use this port and cable if you intend to HotSync your terminal directly to your computer A standard barrel port used for connecting the Power SDE POWER Adapter This power adapter is not included MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Setting up the PS6S1800M Setting up your PS6S1800M is easy and includes only these simple steps l Power Connection 2 HotSync Connection a Connect the serial cable to the computer if you want to HotSync with the computer or b Connect the modem if you want to HotSync with a remote location via the modem Power Connection Plug the US Standard 110V power connector To connect your PS6S1800M to your computer into a grounded wall outlet O Connect your Symbol s power ob adapter into a US standard 110V wall outlet Connect the barrel end of the power adapter into the 9VDC jack on the rear ofthe crad
16. odem est conforme aux exigences essentielles et aux autres dispositions pertinentes de la directive 1999 5 CE Swedish H rmed intygar Mobility Electronics att denna modem star verensst mmelse med de v sentliga egenskapskrav och vriga relevanta best mmelser som framg r av direktiv 1999 5 EG Danish Undertegnede Mobility Electronics erkl rer herved at f lgende udstyr MM modem overholder de vaesentlige krav og vrige relevante krav i direktiv 1999 5 EF German Hiermit erklart Mobility Electronics die bereinstimmung des Ger tes modem mit den grundlegenden Anforderungen und den anderen relevanten Festlegungen der Richtlinie 1999 5 EG N Mobility Electronics Inc MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Greek ME THN TIAPOYZA Mobility Electronics AHAQNEI OTI modem oe 2YMMOPQOONETAI NPO TIZ OYZIOAEIZ ATIAITHXEIZ KAI TIZ AOINE 2XETIKE2 AIATAZEIZ TAX OAHTIA2 1999 5 Con la presente Mobility Electronics dichiara che questo modem conforme ai requisiti essenziali ed alle altre disposizioni pertinenti stabilite dalla direttiva 1999 5 CE Spanish Por medio de la presente Mobility Electronics declara que el modem cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 1999 5 CE Mobility Electronics declara que este modem est conforme com os requisitos essenciais e outras disposic es da Directiva 1999 5 CE Hawnhekk Mobility El
17. or other countries All other registered trademarks trademarks service marks and or logos are the property of their respective companies Mobility Electronics Inc ii MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Contents CONTENTS 55225233523352535838 4852 ana IlI INTRODUCTION aan anna aa ne ana er aan nee 1 Setting up the PS65 L800M an ec ern 2 Produc Technical SUDDOWE van een nee 7 Appendix A Regulatory Information zs2222sssnsnnn nennen meme 11 Appendix B Warranty MOBILITY ELECTRONICS INC invision Serial Modem Charging Cradle User Guide Introduction The invision PS6S1800M serves as an essential data communications device enabling you to synchronize the information on your Symbol SPT 1700 or SPT 1800 terminal and the Palm Desktop software using HotSync technology It also charges both your terminal and a spare battery all while performing HotSync operations via modem or serial connection Using the P5651800M the SPT 1700 or SPT spare Battery 1800 can HotSync with a host computer Charge LED either directly through the serial cable or remotely through the phone lines HotSync Button Spare Battery Charging Slot Terminal Battery Charge LED A switch on the back of the cradle controls which type of sync the cradle is to perform With customized or third party software it can also be used to synchronize your M SPT 1700 or SPT 1800 terminal with
18. radle User Guide Appendix A Regulatory Information Radio Frequency I nterference Requirement FCC Statement This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to FC Tested to comply Part 15 of the FCC Rules These limits are designed to S with FCC Standards provide reasonable protection against harmful interference in a residential installation This equipment FOR HOME OR OFFICE USE generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio or television technician for help Changes or modifications not expressly approved by Mobility Electronics could void the user s authority to operate the product Radio Frequency I nterference Requirement Canada This Class B dig
19. rchaser in the case of the remanufactured product being sold for a period of one 1 year from the date of shipment This warranty is limited to a repair or replacement of the product To obtain warranty service the purchaser must first call Mobility Electronics Inc for an RMA number then return the product to Mobility Electronics Inc for repair or replacement Purchaser shall prepay shipping charges for products returned to Mobility Electronics Inc Mobility Electronics Inc will pay for return of the products to purchaser except that purchaser shall pay all shipping charges duties and taxes for products returned to Mobility Electronics Inc from a country other than the United States Mobility Electronics Inc makes no other warranty of any kind with regard to this material Mobility Electronics Inc shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this material Within thirty 30 days of receipt should the product fail for any reason other than damage due to customer negligence purchaser has the right to return the product for a full refund of the purchase price If the purchaser wishes to upgrade or convert to another Mobility Electronics Inc product within the thirty 30 day period purchaser has the right to return the product and apply the full purchase price toward the purchase of the other product Any other return will be su
Download Pdf Manuals
Related Search