Royal Sovereign THINFLEX RSH-380 User's Manual
Contents
1. RSH 380 5 CONTROL PANEL lt TEMPERATURE gt This button is for changing the temperature of upper and lower rollers Press the up button to increase temperature or the down button to decrease temperature range 20 C 68 F through 150 C 302 F lt SPEED gt This button is used to change the speed of the rollers Settings 1 9 lt T CHECK gt To Check current upper and lower roller temperature Display automatically returns to previous settings after 5 blinks lt REVERSE gt This button is used to reverse the rollers to undo jams and correct misfed documents lt RUN STOP gt This button is used to Run and Stop the machine RS seve A Sovereign 6 FILM LOADING amp THREADING lt Thermal Film Loading amp Threading gt Loading Film 1 Remove the upper and lower film shafts from the machine and load the films do not tighten the core screws at this time 2 To load the top film insert 1 core as shown on Figure 1 Note the direction of the film wound Figure 1 3 Insert the shaft as shown in Figure 2 Figure 2 4 Insert the core plug on the left hand side Figure 3 5 Align and center the film and tighten the two core screws Figure 4 Figure 4 6 Repeat steps 2 through 4 to load the lower film Please note the direction of the film wound for the bottom roll Figure 5 7 Load the upper and lower film shafts on the machine Figure 52. lt Film Threading gt oar WwW PY Idler Laminating Direction Turn the power switch on I position The Power switch is located on the rear the unit Complete the steps in the Loading Film section Set the desired temperature Remove the Front Feed Table Pull down the upper film over the Safety Shield to the lower film align and center the lower film to the upper film and tighten the 2 lower bolt core screws Figure 1 Rewind the upper film until it aligns with the safety cover Thread the film over the Lower Idle Bar and underneath the safety shield until the film rests on the upper roller Figure 2 Put the Front Feed Table back on and close the Safety Shield Figure 3 Press the Run button and thread the film using the Laminating Threading Card Figure 4 RSH 380 Figure 1 Figure 2 Figure 4 E Hove ZRS CS eacien RSH 380 7 BEFORE LAMINATING 8 OPERATING INSTRUCTIONS 1 For High Quality Lamination 1 Turn the laminator on the power switch is located Refer to the Recommended Temperature and Speed Settings section before on the rear of the machine m laminating 2 Adjust the tension of the upper and lower films i The Upper and lower film tension must be same Clockwise to tighten and Counter j 2 Changing Roll film Clockwise to loosen gt GP While laminating if the roll film needs to be replaced press the RUN STOP
3. 13 WARRANTY Royal Sovereign International warrants the equipment sold is free from defects in material and workmanship for a period of One 1 year for Parts and Labor from the date of installation excluding lamination rollers which are warranted for Six 6 months This warranty is extended only to the original purchaser This warranty is the only warranty made by Royal Sovereign International and cannot be modified or amended Royal Sovereign s sole and exclusive liability and the customer s sole and exclusive remedy under this warranty shall be at Royal Sovereign s option to repair or replace any such defective part or product These remedies are only available if Royal Sovereign s examination of the product discloses to Royal Sovereign s satisfaction that such defects actually exist and were not caused by misuse neglect attempt to repair unauthorized alternation or modification incorrect line voltage fire accident flood or other hazard R S H 3 8 0 L am i nator The warranty made herein is in lieu of all other warranties expressed or implied including any warranty or merchantability or fitness for a particular purpose Royal Sovereign will not be liable for personal damage or personal injury unless primarily caused by its negligence loss of profit or other incidental or consequential damages arising out of the use or inability to use this equipment This warranty specifically does not cover damage to laminating rollers
4. 3 Set the pressure lever to the Laminating mode a A button 4 Choose appropriate laminating temperature by gt tip 5 Once the rollers stop cut the upper and lower film remove and replace with new pressing te SA DOWN button E 7 rolls of film 5 When desired temperature is met an alarm will ST ae sound and READY will appear on the ya 3 After lamination f T on eee display i C Hot Spots on the rollers may occur when the machine is idle To help prevent 6 Press the RUN STOP button If rollers don t run T Hot Spots check that the safety shield is completely you must run the sample paper between the front rollers and stop the machine closed while the sample paper is in between the rollers You must leave the sample 7 Position the item to be laminated on the Front Feed Table paper in this position until you laminate again 8 Adjust the film tension or laminating speed if necessary After laminating with Thinflex use Cleaning Paper to clean the rollers 9 Press the RUN STOP button when your amination is finished 10 After finishing your work set the pressure lever to the Hard Board 6mm 11 Turn the Power switch off NOTE Stand by mode If no activity is made within 30 minutes after each use the machine will automatically switch to stand by mode Auto power off mode If the machine is in standby mode and no activity is made for 90 minutes the machine will automatically power off 1
5. The cross cutter is located on the rear exit table of the machine 2 After lamination move the cutter approximately to the center of the application at the desired point of detachment 3 Grasp film with one hand press the cutter downward into he application and slide it first to one end of the application then to the other end to complete the cut Paper speed Temperature 9 RECOMMENDED TEMPERATURE AND SPEED SETTINGS Function 80 g m2 Paper both side can be used 120g m2 100 110 C 212 230 F 200g m2 color paper 25 38mic 1 1 5mil 80g m2 Paper both side can be used 120g m2 200g m2 color paper 100 110 C 212 230 F 75mic 3mil 80g m2 Paper both side can be used 120g m2 100 115 C 230 239 F 200g m2 color paper 100mic 4mil 80g m2 Paper both side can be used 120 125 C 248 257 F 120g m2 200g m2 10 color paper 130 135 C 266 275 F 250mic 5mil 11 A2 ZRS SoN 2 Do not clean rollers with sharp objects use adhesive remover to clean resin off the rollers 10 MAINTENANCE 1 Do not apply any cleaning fluids to the rollers certain fluids may cause damage 3 Use a damp cloth with only water to clean the body of the machine 4 Store machine in a dry clean area 11 TROUBLE SHOOTING GUIDE Problem Possible Caus
6. eet 3 2 PACKAGE Contents sirinin aaa aaa a aaa aaa a ea iaaiiai 3 3 Salety Preca tionS menns rriren enn iaiaaeaia aeaaea Eai aA de 4 A PaSa a a a aE E a E E 4 So GOMUOL Pane yesi air cout cheb eteeeates ceyas eebeaceitardtiatts eared eevaeeeeteateaeb de Taataa 5 6 Film Loading and Threading ccccccceeceeseeeeeeeceeeceeeeeeeeaesaaesaeseeseeseeenaeeeeaees 6 7 ABetore Laminating va is inate ieee lk aan nian 8 8 Operation INStrUCTIONS 2 2 cee ceteeeeecteeeeeeeeeeeeeeeeeeecaeseeeseeesaeesaesaeeseseeetaeeeeeees 9 10 9 Recommended Temperature and Speed Settings ceceeceesereeteeeeeeeees 11 10 MAIMGN ANCE sinna a a Ea 12 11 Trouble Shooting Guide s seseseesesneeneeeeseessesnnenssnensstnsnsnnsnnnnsnnnnnensnnennsnnnnenn 12 12 SPCCHICALIONS siver anak aiia a a EE RA EEA A NEER 13 VS Watra myeusi esien eraud aaia a daade aae adaa 14 2 1 INTRODUCTION Thank you for purchasing a Royal Sovereign RSH 380 Table Top Laminator It has been designed and manufactured to provide years of continuous service For complete operating and maintenance information please read this instruction manual thoroughly Upon receipt of your laminator thoroughly inspect the box machine and all other contents It is imperative that any shipping damage is reported and a claim is filed with the delivering carrier immediately upon receipt 2 PACKAGE CONTENTS Owner s Manual oD ZRS A 3 SAFETY PRECAUTIO
7. NS Failure to comply with any of the following safety procedures could result in serious injury Please read the instructions carefully and keep for future reference 1 2 3 NOOO A 00 10 11 12 13 4 PARTS Only a licensed electrician should install wiring and outlet for the laminator Ensure the unit is plugged into a properly grounded outlet with the correct voltage Keep hands and clothing i e Neckties away from rollers The rollers are pinch points that can trap body parts or clothing and cause serious injury Keep flammable and wet objects away from the machine Place machine on a level surface Avoid excessive sunlight humidity and extreme temperatures Ensure the unit is turned off cooled and unplugged from the outlet prior to moving and or repairing Keep out of reach of children Only Royal Sovereign authorized maintenance and service technicians should make repairs Do not attempt to laminate items that exceed total recommended material thickness for the unit When cleaning the machine don t use flammable sprays or materials Do not touch the rollers when they are hot or place foreign objects inside the machine Do not cover the surface of the machine until the machine has completely cooled 1 FILM UPPER 2 FILM LOWER 3 TENSION CONTROL KNOB 4 TOP HOT ROLLER 5 FRONT FEED TABLE 6 CONTROL PANEL 7 SAFETY SHIELD 8 PRESSURE LEVER br y 3 i X SS a
8. caused by knives razor blades or any sharp objects or abrasives or failure caused by adhesives or damage caused by lifting tilting and or any attempt to position the machine other than rolling on the installed castors or feet on even surfaces or improper use of the machine Warranty repair or replacement by Royal Sovereign or its authorized Reseller s does not extend the warranty beyond the initial one year period from the date of installation Unauthorized customer alterations will void this warranty CORPORATE HEADQUARTERS Royal Sovereign International Inc 2 Volvo Drive Rockleigh NJ 07647 U S A TEL 1 800 397 1025 FAX 1 201 750 1022 E mail info royalsovereign com RS Holland B V Royal Sovereign Inc lt oversea Sales Office gt Columbusstraat 25 3165 AC Rotterdam 1001 World Meridian Il 426 5 Gasan dong The Netherlands Geumcheon gu Seoul 153 759 KOREA E mail paulchoi royalsovereign com TEL 82 2 2025 8800 FAX 82 2 2025 8830 henryabrahamian royalsovereign com E mail sales royalsovereign com RS Canada Inc RS International Australia PTY LTD 164 Oakdale Road Toronto Ontario M3N 2S5 30 Prime Drive Seven Hills NSW 2147 Australia CANADA TEL 61 2 9674 2127 TEL 1 416 741 8400 FAX 1 416 741 8185 FAX 61 2 9674 2027 E mail info royalsovereign com E mail salesaust royalsovereign com 14 TABLE OF CONTENTS TOPIC PAGE Te MFO GUCUION sisarena inenen aa E aa ated eet a
9. e Possible Solution Rollers do not operate after the RUN STOP button is pressed 1 Safety coveris opened 2 Power cord is not plugged in 1 Check to make sure the safety shield is closed 2 Check the power cord Roller is not heating Call your authorized dealer Call your authorized dealer Result of lamination is waved 1 Film tension is unbalanced 2 lower idler bar is not located in proper position 1 Adjust film tension by rotating tension handle 2 Push idler bar up Result of lamination is not clear 1 Temperature is lower or speed is higher than recommended 1 Adjust speed and temperature 12 RSH 380 12 SPECIFICATIONS RSH 380 AC 100 200 220 240V 50 60Hz 120V 60Hz Description Power supply Power consumption 1500W Max laminating width 380mm 15 25 250 mic 1 10mil 5m min 16 4ft min Film thickness Max laminating speed Ready time 8min Heating method Hot roller DC geared 150 C 302 F Speed control 9 settings Driving motor Max Temperature contro Transport type 4 Roller Film core size 1 2 25 3 Cross cutter es lt Hot lamination es Mounting thickness 6mm 0 24 Reverse Yes 550 x 690 x 605 mm 21 5 x27 x24 45kg 99 Ibs 800 x 750 x 650 mm 31 5 x 29 5 x 25 5 57kg 126 Ibs Unit dimensions w x d x h Unit weight Carton dimensions w xd xh Carton weight 13
Download Pdf Manuals
Related Search